Reviews
![Steel Long Swingarm [10cm Long] (with Stabilizer)](https://img.webike-cdn.net/catalogue/images/44098/574_TS.jpg)
Fits: HONDA GORILLA, HONDA MONKEY
It's not a good look.
Good product at a glance.
It is a product that should not be bought by anyone who cares about the fine appearance of the product.
Paint is thick, but peels easily when Gold genus parts rub against it.
Some of the iron used in Large land rusts quickly.
It would be better to always have a Rust protection such as Spray or Touch up paint.
The weld marks are as clean as JAPAN products without any strange stubbers.
More eye-catching than that.
Is it for the chain line? Maybe, Stubby has a strange shape.
Large to the Left Side.
Distorted to the Left Side to the extent that it may interfere with the Side Stand.
It is so large that you may wonder if it is reused for Wide Stubby that was left over from other products.
I mean, you're recycling." It's so oddly shaped that it nods to the opinion that determines
Even images of stores other than webike use the oblique illusion to make them unrecognizable.
Since MONKEY itself is designed with very short swing arms, the pivot position is in an impossible position for a normal motorcycle. Therefore, if you use Long Swing Arm, the chain itself will sag when you ride due to the bad combination with Rear Suspension. If it is a Stubby to avoid the sagging, it may be acceptable, but the appearance is very bad.
I'm sure Stubby won't interfere with Chain if we leave this much space open, right?" (grin)" It is so crooked that one can almost hear the voice of
Stubby is not suitable for the low &long ride height that Japanese people like.
If the Swing Arm is almost horizontal at 8Inch, it'll scrape on the sidewalk steps at the entrance to the store.
It was about 2-3 inches off the ground visually when adjusted with Jack without suspension.
I was expecting a Swing Arm with Stubby that had a sports taste.
The product that arrived was a Swing Arm with a perverted Stubby, which is a straight line of colorful things......orz
The strength itself is steel + Stubby reinforcement, so it's pretty pushy.
When putting the hubs in, if they went in at a slight angle, it was quite difficult to fix.
It seems that there is no strange rustling even if it is loaded with luggage and carried on its back and ridden over 100 km overall on mountain passes and elevated bumps.
Because I feel comfortable seeing images of people working together on social networking sites, etc.
Once assembled, it's a discreet object.
If you're like me, you're looking for a "Quantity:Pair (for Left and Right) For those who prefer "symmetry and firm symmetry", this is a very uncomfortable part!
However
"Look." Than "real" (i.e. not "actual") I can recommend it to those who take
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
Lowest quality
(Note:WeBig has been good to us. It's about the item itself.
Distance Collar is lowered by its own weight and Axle does not enter from the side.
Through Mr. WeBig. Funny, isn't it?" I said.
"It's the part that keeps Bearing from getting inside, so it's not a
It is slightly movable before installation 。 "
He was kind enough to tell us about the body structure.
（The OEM has a flange that is press-fitted into the pipe so that it fits almost in the center while still wiggling around. However, this one does not have a flange and is just a Pipe. Of course, there are some models that have only a pipe, but in those cases, the inner diameter of the hub is narrower so that there is not much gap from the center even though it is a pipe shape.
When you install it on the car body, of course it is in this direction (the bottom side of the image is the ground), so I guess it means that you should insert it after putting out the Center by inserting a Driver from the opposite side….
The most surprising thing is this. It's Spec. This is Tanaka Shokai, which says
You have to do a lot of them to know if it's too Gap (too Large). （I'm sure you can't tell that this is too Gap (too Large to play with) unless you play with a few units.
I wonder if they would be able to push through with that (Spec. ), I guess I'll be able to push through with that (Spec.
View detail
Fits: HONDA Dax 70, HONDA cub, HONDA monkey, HONDA dachshund, HONDA Mighty Ducks (ST90)
Not compatible with MONKEY.
Although it is said to be compatible with the MONKEY, in reality, it interferes with the chain case cover of the STD of AB27 and Z50J and cannot be installed without additional processing with a grinder or milling machine, etc. although it mates with the spline of the shift shaft. It is a terrible thing. View detail
Fits: HONDA MONKEY, HONDA GORILLA, HONDA DAX, HONDA CHALY 50, Others , HONDA DAX70, HONDA CHALY 70, HONDA ST90 (ST90)
It is not usable
First of all, the Material is too hard and seems to be Plastic, not Rubber
It looks slippery on a rainy day
Besides, it's guaranteed to fit, but I couldn't install it on my GORILLA 6v
View detail
It's not working
Pedal welding is crude and the hole diameter of the Pedal is Large in relation to the body's mounting shaft Kikki If you install it as it is, the Pedal is rattling and cannot be used
If you are an amateur who cannot process or adjust the product, you can't pimp it is a good idea
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
inferior goods
5LMONKEY's Dust Boots for Normal stem, Inner's thick hydraulics I bought it because I thought it would be NORMALInner-compatible, but it's not The diameter was not useless because of a governor with a large diameter than NORMALInner
When you install it, there will be a gap between the inner and the dust boots and a lot of grease will come out I'll come back to you
The OEMs are made with a proper Guide, but this one is just thin and soft Rubber cover
The diameter is no good, the Material is no good, and the construction is no good
It's so bad that I'm not even going to ask for a return or return Gold
It's just a parody product, it's not a motorcycle part
Tanaka Shokai, thank you very much for your humorous products
That's what I'm talking about
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
Terrible quality and unsafe for use.
This brake pedal is worse than the photo supplied. It’s poorly made just like the quality of alloy used to produce this product. Wouldn’t recommend to use this pedal as it bends when pressure is applied to use the rear brake, due to it being soft. I would return it if webike would allow. Don’t purchase as it’s not even worth a few dollars. Very disappointed. Will not buy tanaka parts again. View detail
Fits: HONDA DAX70, HONDA CHALY 70, HONDA MONKEY, HONDA GORILLA, Others , HONDA CHALY 50, HONDA DAX, HONDA ST90 (ST90)
Sorry!
I did not notice when goods were sent, but installing Quantity : Pair (for Left and Right) It was confirmed that one had a beautiful Color : It was Yellow but the other faded Color : It was Yellow..
I thought about replacing it, but after I installed it I gave up..
Because I understand it by appearance, I'd like you to check it before shipping!
View detail