Reviews
More than Bore up.
Swapped from SUPER CUB 50 OEMEngine
With Engine itself pon
The carburetor came with a 16π? The carburetor came with a 16&pi carburetor, but I used a pc20 funnel and a YOSHIMURA intake manifold. The rest is KITACO clutch wire and clutch lever.
FSprocket exchanged R for 15, or was it 38?
I'm not sure about Included Parts:as you don't mention it specifically,
I tried to use the Indicator and found that there are two in the box, one for the carburetor side and the other for what? I tried to use the Indicator and found two in the box, one for the carburetor side and one for what? Well, I don't need it because CUBOEM13π is obviously not enough for 86cc lol.
The original engine oil was replaced with G2Oil after warming up and breaking in salad oil.
I don't know about the attached carburetor, but after breaking in, full throttle, well, thanks to the pc20, the CUB is no longer a CUB. 60kmMeter is swept away in about 5 seconds.
Another AA01 centrifugal 3 speed 88ccHigh Camshaft18πcarburetorOthersSprocket uses the same size, well, Gold amount is more expensive to bore up, so it is still recommended for those who want Manual clutch.
Installation can be easily done by one person.
The difficult part would be to modify the terminals to match the Engine side when using OEMHarness.
I think it would be more of a hassle to replace even the Harness.
As you may have read in other sites or on our side, the first time GEAR enters the market, it is very reluctant to do so.
Neutral goes in for me, but I often have trouble returning to 1st gear from 2nd gear.
The wiring diagram in the Instruction Manual was Harnessfor MONKEY, but the color was the same in CUB.
I don't know how durable it is since it is currently just loaded, but I hope it was a hit.
View detail
Fits: HONDA CUB, HONDA MONKEY, HONDA dachshund, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA dachshund, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
Easy to change carb position
Casting seems very strong, however the casting port hole for the engine side is not perfect. I'll need to use a Dremel to tidy up the port as can be seen in the photo. Otherwise I feel it will not produce as good as power as it could. Installation is very easy on monkey due to being able to position the carb however you like. Product was priced well just a shame about the casting hole. Webike is always very quick with shipping A+ View detail
Fits: HONDA MONKEY, HONDA DAX, HONDA CHALY 50, HONDA CUB, HONDA DAX70, HONDA CHALY 70, HONDA ST90 (ST90)
Recommended
If you don't care about how it looks, why not?
There is a matter of taste.
It's cheap, so I'm happy with it.
View detail
Fits: Others Vehicles equipped with CUBetc. Horizontal TypeEngine, HONDA MONKEY
Communication failure? Repost.
If you are OEM with Cell motor, you don't need to buy CUB harnesses.
[How is it used?
I purchased this LITTLE CUB to improve its street riding performance while restoring the long-neglected LITTLE CUB that was handed down to me.
From a friend Cheap Bore Up Kit." recommended, but I wanted to save the Normal engine for the long run in case of an emergency. "What can we do to help?" I found this product while browsing Webike's site.
Was the one you received as per Image?
I decided to purchase the product after seeing the introduction image in the Site and the video of the person who installed the product in the Video Site, so the product was just as I had imagined.
Was the installation difficult?
Simply replace Engine Only." Then it is not difficult because it only requires 2 Bolts and Wiring removal.
However I can get on board with no problems." It requires some knowledge and Large amount of effort to bring it to the state.
How was your experience with it?
We have not been able to gain any distance since installation, but so far it is running fine for the amount of work we have put into it.
But if you look at the Review here and the video Site. Maybe it's not just a safe ride forever?" It's like...
I think I have a hit ha Gap. Bingo I just hope that we are pulling the
[Included Parts:were they on?
35,680 yen in bare bones with Engine (14 Driven Sprocket included) Body, Carburetor, Intake, Kick pedal, Change pedal, Relay and CDI etc...
I have added Harness for CUB with Option, "Elementary." I believe that a MONKEY type Harness will be included in the state of
If you are a MONKEY type. "Elementary." Kit may be enough to form a Large body (wishful thinking).
[Was there anything that disappointed you?
from the start Harness for CUB The Optionally purchased Harness is almost identical to the OEM Harness that originally came with the vehicle, and was a waste of money for a Harness that will not be used.
And to begin with, the Harness on the Engine side does not match the Harness for the CUB purchased with the Option.
I went all the way to this Engine. Harness for CUB What an Option if it is available! Harnesses the Wiring process to fit this Engine. The Harness side is the OEM standard Wiring & Connector, but the Engine side has a completely different Wiring process.
OptionHarness was never used at all because the Engine side Wiring process & processing had to be done.
Forced to think Positively No Cells. It may be good when installing in a CUB, but my CUB was with Cell motor, so it was a complete waste of Gold (of course, at the time of purchase, there is no mention of harnesses to make a Cell-less unit Cell-compatible).
Everything. Universal Type. So, in the CUB system, with the attached carburetor & intake manifold. OEM style." I can't get around the (is it Large sturdy if it's a MONKEY?). (Would MONKEY be Large sturdy?).
Other items that would be helpful
Point and hang of installation
The level of difficulty will increase unless you are able to see and understand the wiring diagram.
[Availability and clarity of the Instruction Manual
An Engine Wiring Diagram for Tanaka Shokai is included in the package, but it is not sufficient, so a Wiring Diagram for the vehicle you wish to install is also required.
Setting may not fit in a pontoon, and this is a product for those who can enjoy and adjust it.
[Notes]
Please check the introduction & description section of the product carefully.
I was fortunate to have a friend who was good at electrical systems, so I asked him to do the Wiring process (a whole lot of work).
If you are a beginner or not good at electrical stuff, as I am. "Decent friend." It may be better to rely on a professional or paid PRO.
[ITEMS TO BUY TOGETHER
If you want an OEM look. SUPER CUB90 If you want to create a custom look and feel, you should buy custom parts to go with it.
[Opinions and requests to Manufacturer
Even though it is an overseas product, it is very nice to be able to purchase Complete engine at this price.
In addition to the engine, the Honda Horizon TypeEngine vehicles have a wide selection of parts at reasonable prices.
View detail
Fits: Others Vehicles equipped with CUBetc. Horizontal TypeEngine, HONDA MONKEY
If you are OEM with Cell motor, you don't need to buy Harness for CUB, but Large sturdy (Wiring is required anyway).
[How is it used?
I purchased this LITTLE CUB to improve its street riding performance while restoring the long-neglected LITTLE CUB that was handed down to me.
From a friend Cheap Bore Up Kit." recommended, but I wanted to save the Normal engine for the long run in case of an emergency. "What can we do to help?" I found this product while browsing Webike's site.
Was the one you received as per Image?
I decided to purchase the product after seeing the introduction image in the Site and the video of the person who installed the product in the Video Site, so the product was just as I had imagined.
Was the installation difficult?
Simply replace Engine Only." Then it is not difficult because it only requires 2 Bolts and Wiring removal.
However I can get on board with no problems." It requires some knowledge and Large amount of effort to bring it to the state.
How was your experience with it?
We have not been able to gain any distance since installation, but so far it is running fine for the amount of work we have put into it.
But if you look at the Review here and the video Site. Maybe it's not just a safe ride forever?" It's like...
I think I have a hit ha Gap. Bingo I just hope that we are pulling the
[Included Parts:were they on?
35,680 yen in bare bones with Engine (14 Driven Sprocket included) Body, Carburetor, Intake, Kick pedal, Change pedal, Relay and CDI etc...
I have added Harness for CUB with Option, "Elementary." I believe that a MONKEY type Harness will be included in the state of
If you are a MONKEY type. "Elementary." Kit may be enough to form a Large body (wishful thinking).
[Was there anything that disappointed you?
from the start Harness for CUB The Optionally purchased Harness is almost identical to the OEM Harness that originally came with the vehicle, and was a waste of money for a Harness that will not be used.
And to begin with, the Harness on the Engine side does not match the Harness for the CUB purchased with the Option.
I went all the way to this Engine. Harness for CUB What an Option if it is available! Harnesses the Wiring process to fit this Engine. The Harness side is the OEM standard Wiring & Connector, but the Engine side has a completely different Wiring process.
OptionHarness was never used at all because the Engine side Wiring process & processing had to be done.
Forced to think Positively No Cells. It may be good when installing in a CUB, but my CUB was with Cell motor, so it was a complete waste of Gold (of course, at the time of purchase, there is no mention of harnesses to make a Cell-less unit Cell-compatible).
Everything. Universal Type. So, in the CUB system, with the attached carburetor & intake manifold. OEM style." I can't get around the (is it Large sturdy if it's a MONKEY?). (Would MONKEY be Large sturdy?).
Other items that would be helpful
Point and hang of installation
The level of difficulty will increase unless you are able to see and understand the wiring diagram.
[Availability and clarity of the Instruction Manual
An Engine Wiring Diagram for Tanaka Shokai is included in the package, but it is not sufficient, so a Wiring Diagram for the vehicle you wish to install is also required.
Setting may not fit in a pontoon, and this is a product for those who can enjoy and adjust it.
[Notes]
Please check the introduction & description section of the product carefully.
I was fortunate to have a friend who was good at electrical systems, so I asked him to do the Wiring process (a whole lot of work).
If you are a beginner or not good at electrical stuff, as I am. "Decent friend." It may be better to rely on a professional or paid PRO.
[ITEMS TO BUY TOGETHER
If you want an OEM look. SUPER CUB90 If you want to create a custom look and feel, you should buy custom parts to go with it.
[Opinions and requests to Manufacturer
Even though it is an overseas product, it is very nice to be able to purchase Complete engine at this price.
In addition to the engine, the Honda Horizon TypeEngine vehicles have a wide selection of parts at reasonable prices.
View detail
Fits: HONDA CUB, HONDA MONKEY, HONDA GORILLA, HONDA DAX
I put it on a 75cc GORILLA.
I put it on a 6VGORILLA that I bore up to 75cc.
The Fuel Cock had rotted out of the OEM and had been replaced with an external one.
Change the two Bolts on the Head side to M6 25mm.
I just replaced the Accelerator Wire for Big carburetor and it arrived as is.
Power Filter is KITACO's 35-pipe
I took it apart and reassembled it as it was and tightened the ThrowScrew a little.
When I took it apart again after running it for a bit, I found iron powder in the float chamber.
I just cleaned and assembled it and it is running well.
The Choke Lever is now on the Exhaust System side, and it is difficult to touch.
Other than that, I have no complaints.
View detail
Fits: Others Vehicles with 12vCDI ignition single-cylinder engine, HONDA MONKEY, HONDA GORILLA, HONDA LITTLE CUB, HONDA XR50R, HONDA CRF50F, HONDA Monkey Baja, HONDA DAX, HONDA MAGNA50
Starting and Idling are OK, now it's time to observe the durability.
Purchased because of problems with starting and Idling.
After installation, the above two points were immediately resolved.
The installation method is easy to find on the Net, so no problem.
No instruction manual.
1.Remove the leg shield
2.Remove the Right Side Cover, and then remove the Battery Cover and Earth?
3.Remove the Left Side Cover and remove the nut where the IgnitionCoil is fixed.
4.Replace IgnitionCoil
5.Remove the plug cap and thread the cord through.
6.Return Battery coverretc.
7.Turn in the plug cap and insert it into the plug.
8.Return the leg shield.
Now it's time to observe the progress of durability.
I'm a little concerned because of the low price, but ….
View detail
Fits: HONDA SUPER CUB 50, HONDA SUPER CUB 90, HONDA MONKEY
Wow that's cool
[How is it used?
OEM Oil cap was ruined and
Changed from OEM to this because of this.
Was the one you received as per Image?
Yes
Was the installation difficult?
It's easy
Just take it off and put it on.
Confirm that ORing is present
How was your experience with it?
The beautiful Plating has a strong presence.
To the One point of the Clutch cover.
[Included Parts:were they on?
[Was there anything that disappointed you?
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Fits: HONDA MONKEYetc.Horizontal TypeEngineUniversal
It's something we can use!
Used for DAX.
The Carburetor can be oriented anywhere in 360 degrees, so the Clutch Wire and
Fuel Hose etc. can be avoided.
The Carburetor can be installed in the position of your choice, so it is easy to install.
Very user-friendly product.
I was relieved to find that there was no secondary air suction, which was a slight concern.
Other Brand ProductImmani in general:・・・・
Since the inside process is Decoration bumpy, it was covered with 300-grit paper.
Finish by polishing with No. 800 for cleanliness.
But I think this area is also one of the fun parts of playing with MINI4♪
View detail
Fits: HONDA MONKEY, HONDA DAX, HONDA CHALY 50, HONDA CUB, HONDA DAX70, HONDA CHALY 70, HONDA ST90 (ST90)
Cheesy indeed.
As you would expect from a cheap product, the texture is incredibly cheap.
I thought it would rust quickly from the looks of it, but the fact that it does not rust unexpectedly is something to be appreciated.
View detail
I can finally put it on Reserve while I'm driving.
I used it on my '01 MONKEY.
The position of the Fuel Cock has changed 180? since the engine was bored up and the carburetor was replaced, so I used to reverse the Normal cook, but when I reverse it, the cook buffers the carburetor, so I shortcut it. I had to get off once and then switch to Reserve.
MONKEY has only half the GS capacity of GORILLA, so I was running with trepidation when I ran more than 120km, but finally I was able to put it in Reserve while running. This will save me from having to stop alone while touring with a group.
The Cook is not OEM Parts, but I used the Cook of Ki*co for GORILLA before, but the packing in the Cook was bad and did not last half a year.
View detail
Fits: HONDA hunter turnip, HONDA cub, HONDA cub, HONDA cub, HONDA cub
Good product at an affordable price.
This is a replacement for an old CUBC70Z2 from around 1970 that leaked gasoline when moved from the RES position. I am satisfied with the product. View detail
Is the initial performance a hit?
LITTLE CUB which had Engine Displacement VolumeUp to 108? I purchased Bullet TerminalKit, but I had a little trouble because the wiring color of Instruction Manual was slightly different. The carburetor uses KEIHINPC24φ which was originally used. MJ is #100, SJ is #35, Air Screw 1 turn back. I finished the break-in of 300km with the Chinese Plug and ran 45km now. The amount of OIL is less than 1L. According to the explanation, Gasoline is Regular, 7.75ps/7500rpm, and it drops about 1ps from CT110 HUNTER CUB8.8ps/7000rpm of the same Engine Displacement Volume. There is no instruction manual, just a seal on the surface of the engine that says "run under 50?/h for the first 300km" in English version.
The Idling stabilized after the break-in period, and it starts with a single chalk even on cold mornings, and the low-speed torque is strong and stubborn enough to withstand TRIAL play. I have run up to 80?/h on level ground, but I think there is still room for more. This engine does not have an internal oil filter, so it would be better to change the oil every 1000 miles. I don't know about the durability of this engine as it is only 450 miles old. The clutch feels a little heavy, but if you change to a hydraulic lever, you should have no problem. Chinese products seem to be hit or miss, but this engine may have been a hit when it comes to initial performance.
View detail
It was better than I expected.
Stick with NORMALSpec.
I made this carburetor.
I'll just pimp it out for now.
The Engine has been started.
With a few tweaks, so does Idling.
It's stable.
The problem started to occur while the machine was in use.
I might get it.
I think it's a good purchase.
View detail
abstinence from consideration
Used in the interim until the Fuel Cock on MONKEY R is repaired. Quantity in Bolt as per prior web information:I can't stop 2pc, even though it's just a little more. I also took it apart and found that it has a cup type filter like OEM Product. There are no leaks and the packing can be replaced from the beginning because it is Screw stopper. If only the hole pitch was correct, I could have used it as is. 。 This is a great price for this quality. View detail
We're in good shape
6VGORILLA Used for OEMTank
I've been using Kioco's Cook, but even with the Cook off, it's still leaking fuel I'm not sure if it's a good idea to buy another manufacturer's product, but I think it's a good idea to go to Ue-Big's page I bought it because it was available and the price was quite affordable
The tube structure inside is a little shorter than OEM parts and the position of the spare space is different It's not that much of a concern since it's not a 1-liter difference in reserve (Because GORILLA comes in 9 liters.)
And Cook's ON.OFF.RES. is stamped in a funny way, but it's where you always see it I don't care because it's not
Anyway, it's less than half the price of other Manufacturer's parts, so that's good
Even the rubber packing on the tank, even the torque-tightening torque is wrong If not, you can use it
View detail
Satisfied with the performance of the engine, but if you are prepared to process it, you can buy it from Recommendation
I bought it after hearing about it from a Chinese EngineOwner I met while touring I have driven 400km now and I am satisfied with the performance
There is no particular Trouble
When mounting on AB-27MONKEY, the Swing Arm side mount width is set to Normal Since it was wider than the engine, it shaved with File about 1mm
And because the head of the Bolt in the photo protrudes from Mount and interferes, the Honda OEMBolt I replaced it with
Carburetor is PC20 and Exhaust System is Takagawa's Exhaust System Up Type and Wiring is OEM Changed to the same type of Connector, Coupler connection to NORMALWiring, CDI It is also NORMAL, but the low-speed torque also turns smoothly to high rpm without complaint It is a characteristic that is easy to ride The fuel consumption is 50km/l if the speed is less than the legal speed, but if you use a lot of high revolutions, the fuel consumption is less than 40km/l The Oil uses Honda OEM G1 10W-30
I was prepared for it, but it's not going to be a pimped-out version, so it's a processing premise and a cosmetic purchase Recommendation
View detail
For those of you who are doing Restore, Recommends
It is almost the same shape as the OEM The shape is different, but the important part is almost the same shape
I put Float into PAcarburetor which I had originally, and it works normally I did
Performance is about as good as it gets as a normal Carburetor
I idled it by pontooning it to 6VMONKEY, but I noticed that it had a slightly darker burn to
It needs to be adjusted, but if you're into the OEM form, it's not a bad buy
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA CHALY 70, HONDA CHALY 50
Anyway.
By all means Carburetor setting did not go well, there was an add Vise with? In the ignition system, I bought it as soon as I exchanged Point.
Although it has not installed yet, Plug cap seems to be no problem especially when it is separately required.
I do not think Ignition coil is the cause, but since many obsolete numbers came, something, I will try to refresh once.
View detail
Fits: HONDA Shirley 70, HONDA Shirley 50., HONDA Shirley 70, HONDA Shirley 50.
CHALY a 2 to PC 20
It was for VM 22 and 16, but it is diverted to PC 20 by self-responsibility. Since the Carburetor installation pitch is the same 48 mm as VM type Insulator, Cost performance is also available and we introduced this.
It was a good shopping because Exactly and Carburetor fit in Limit Space of CHALY A and did not interfere anywhere. Of course, OEM Cover is removed. Although the caliber was modest, it was easier to set out on the PC system than the Large caliber as if it was stupid. I think that it is intended for people who can adjust the story with carburetor and Head with the degree of correction.
View detail