Reviews
Fits: HONDA ST90 (ST90), HONDA CHALY 70, HONDA DAX70, HONDA CUB, HONDA CHALY 50, HONDA DAX, HONDA GORILLA, HONDA MONKEY
I use it to compare with KITACO's
Half the price compared to KITACO's.
I installed it on my other Bore up CUB and
We are comparing the effects.
The color is good, the texture is good.
View detail
Fits: HONDA MONKEY, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
I can use it normally.
DAYTONA's Bore Up Kit (HYPERHead series 88cc) I use it in conjunction with 。 I can use it normally but I am not sure how durable it is. View detail
Fits: HONDA CUB, HONDA MONKEY, HONDA GORILLA, HONDA DAX
just right (time, size, length, etc.)
I used it on my MONKEY with Initial ModelDAX70Engine.
The diameter is not too large and not too small, so it is very good.
However, because it interfered with Fuel Cock when I installed it, I used Light Manifold Set for pc20 of KITACO which I had left over without Indicator.
Main jet and Pilot Jet standards are
Main jet MikuniRound Type Special Large
Pilot Jet For MikuniTMR
can be used.
Setting will be adjusted later.
I hope this is helpful
View detail
Fits: HONDA MONKEY, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
It's up and running, but...
I consulted with a motorcycle shop because my Maguna 50, which is a very beautiful car with 8,000km on the clock, was not running well (cause unknown), and they pointed out that the cause was a bad Tappet, Pilot, Main jet, and CDI. So I changed each jet, replaced the carburetor packing, cleaned Plug and Element, and tried to change CDI by the way, I was looking for CDI, but OEM is expensive, and famous manufacturer (Posh, etc.) Other Brand Product is around 7000yen. And because it cannot be said that it is cheap, I search for a cheap Chinese product though I do not trust it much. The price was about 20% of the other products of 1100 yen in this shop of the MotorcycleParts handling shop which is often seen, and because the Review was also good though only two cases, I bought it at the risk. "Does it apply to MAGNA 50?" I was expecting to be able to install it because I read in the review that it was possible to install it in the same kind of Jazz as MAGNA. The MAGNA50 had a 6Pin and a Pink Wiring, but the product did not. I had no choice but to replace all the other concerned parts and started with one extra Pink wire. As a result, it went well, but I don't know if it was the effect of the CDI or the problem with the other parts. Besides, what worries me now is that I haven't connected the Pink's wire. Is this a good thing as it is, or will it hinder me in some way if I don't? I am very worried in addition to the fact that it is a Chinese product. View detail
Fits: HONDA MONKEY, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
It is as good as OEM Parts.
Replaced because it didn't rotate more than Idling and got bumped.
Compared to the price of OEM Parts CDI, the price is much lower and the performance is the same.
The Coupler shape was also OK, and it became very good condition by exchanging with Plug at the same time.
I was under the illusion that the Carburetor setting had suddenly changed, and I tried everything, but it just didn't work.
I found a hint on the net that the cause was the CDI and replaced it. If you have the symptom of not turning up to the top for some reason, why don't you suspect the CDI?
View detail
I can finally put it on Reserve while I'm driving.
I used it on my '01 MONKEY.
The position of the Fuel Cock has changed 180? since the engine was bored up and the carburetor was replaced, so I used to reverse the Normal cook, but when I reverse it, the cook buffers the carburetor, so I shortcut it. I had to get off once and then switch to Reserve.
MONKEY has only half the GS capacity of GORILLA, so I was running with trepidation when I ran more than 120km, but finally I was able to put it in Reserve while running. This will save me from having to stop alone while touring with a group.
The Cook is not OEM Parts, but I used the Cook of Ki*co for GORILLA before, but the packing in the Cook was bad and did not last half a year.
View detail
Fits: HONDA hunter turnip, HONDA cub, HONDA cub, HONDA cub, HONDA cub
Good product at an affordable price.
This is a replacement for an old CUBC70Z2 from around 1970 that leaked gasoline when moved from the RES position. I am satisfied with the product. View detail
Fits: HONDA SUPER CUB 50, HONDA SUPER CUB 90, HONDA monkey, HONDA monkey
Dress-up effect and heat dissipation effect.
I damaged the cylinder head cover with a tool when I overhauled the engine.
Material to make it look as good as possible.:I bought this one from Aluminum.
good point
Just replace with OEM cylinder head cover.
Lighter than OEM.
Gasket is also included for easy replacement.
■Material:Aluminum is also a good conductor of heat and can be expected to dissipate heat.
It's aluminum, so it's not polished.
A bad point
If you don't need it, you don't need it.
I bought it for the dress-up effect and the appearance, but when I thought about it, there is also a lot of Merit in this part.
I'm glad I bought it personally, because I want my Engine to be clean inside and out.
View detail
Fits: HONDA Mighty Ducks (ST90), HONDA Shirley 70, HONDA Dax 70, HONDA Shirley 50., HONDA cub, HONDA dachshund, HONDA monkey
Used for assembly from Frame
I'm a little concerned about the rattle when the KICK is closed. View detail
Fits: HONDA ST90 (ST90), HONDA CHALY 70, HONDA DAX70, HONDA CUB, HONDA CHALY 50, HONDA DAX, HONDA GORILLA, HONDA MONKEY
Replacement for OEM drain bolt.
The head of the Bolt on the OEM Drain bolt was blistered, so I replaced it with a magnetic one.
good point
Iron powder will be caught properly.
I think it's cheap if you think of it as this kind of product.
●Washer is also included.
A bad point
Internal environment parts and replacement in Engine is recommended.
In my case, I bought and replaced the Bolt because of the problem of the Bolt caused by the aging of the car body, and I am glad I changed it.
It's not about running better, it's about always being better.
View detail
Is the initial performance a hit?
LITTLE CUB which had Engine Displacement VolumeUp to 108? I purchased Bullet TerminalKit, but I had a little trouble because the wiring color of Instruction Manual was slightly different. The carburetor uses KEIHINPC24φ which was originally used. MJ is #100, SJ is #35, Air Screw 1 turn back. I finished the break-in of 300km with the Chinese Plug and ran 45km now. The amount of OIL is less than 1L. According to the explanation, Gasoline is Regular, 7.75ps/7500rpm, and it drops about 1ps from CT110 HUNTER CUB8.8ps/7000rpm of the same Engine Displacement Volume. There is no instruction manual, just a seal on the surface of the engine that says "run under 50?/h for the first 300km" in English version.
The Idling stabilized after the break-in period, and it starts with a single chalk even on cold mornings, and the low-speed torque is strong and stubborn enough to withstand TRIAL play. I have run up to 80?/h on level ground, but I think there is still room for more. This engine does not have an internal oil filter, so it would be better to change the oil every 1000 miles. I don't know about the durability of this engine as it is only 450 miles old. The clutch feels a little heavy, but if you change to a hydraulic lever, you should have no problem. Chinese products seem to be hit or miss, but this engine may have been a hit when it comes to initial performance.
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
6VGORILLA.
Postscript.
I won't be able to keep it up!
Need to remove long holes and interfering parts of the frame.
I don't know about the 12VFrame.
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
6VGORILLA will be used for
G-Cla-Minimoto has a similar product and I've already experienced the effects.
I bought it this time because it is the cheapest one at
Nut is not attached, so you need to get a long one.
I will add the accuracy after I install it.
View detail
It was better than I expected.
Stick with NORMALSpec.
I made this carburetor.
I'll just pimp it out for now.
The Engine has been started.
With a few tweaks, so does Idling.
It's stable.
The problem started to occur while the machine was in use.
I might get it.
I think it's a good purchase.
View detail
Fits: HONDA MONKEY, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
Cosmo.
Installed on JAZZ. I was able to install it without any modifications. It has been about 2 months since I installed it and it is running great. The only thing left to do is durability. View detail
Fits: HONDA MONKEY, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
Well done, sir
It is the same shape as OEM parts, so it was easy to install. It has been 2 months since I replaced it. The cost performance is excellent. View detail
abstinence from consideration
Used in the interim until the Fuel Cock on MONKEY R is repaired. Quantity in Bolt as per prior web information:I can't stop 2pc, even though it's just a little more. I also took it apart and found that it has a cup type filter like OEM Product. There are no leaks and the packing can be replaced from the beginning because it is Screw stopper. If only the hole pitch was correct, I could have used it as is. 。 This is a great price for this quality. View detail
Even with a pontoon and screw adjustment, it's not good.
I bought the ASSY because it's cheaper than buying a packing set.
There were dents on the air cleaner side of the first carburetor that arrived, so I replaced it.
The next one I received was also a ding in the same manner, so the inquiry response was fine.
I'm not sure by which criteria you can say it's okay, but I'll take it.
I installed it on the MONKEY, but it's not in good shape at all, and I'm not sure if I can adjust the Pilot screw or not.
When I opened the Throttle instead of the Level, it came with Rose, and I thought it was just a defective product.
I reverted to the Normal cab that I had on.
It was a disappointing product, though I can't judge it by looks alone.
View detail
Fits: HONDA ST90 (ST90), HONDA CHALY 70, HONDA DAX70, HONDA CUB, HONDA CHALY 50, HONDA DAX, HONDA GORILLA, HONDA MONKEY
Chinese Engine Essentials
I installed it on my Loncin 125.
When you change the oil, you can see the effect of iron filings on it.
It's a must-have for the Chinese Engine.
View detail
Fits: HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA dachshund, HONDA Shirley 50., HONDA cub, HONDA Dax 70, HONDA Shirley 70, HONDA Mighty Ducks (ST90), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA dachshund, HONDA Shirley 50., HONDA cub, HONDA Dax 70, HONDA Shirley 70, HONDA Mighty Ducks (ST90)
Hmmm…
It looks, Cost, and I think it's pretty good, but
The accuracy of the Screw thread is poor.
Even if you turn the Screw by hand, it stops on the way, and it seems to go in if you force it in, but I quit because the Engine side seems to be painful.
I think there is a hit or miss Gap, though.
View detail