Reviews
Fits: HONDA DAX, HONDA CHALY 50, HONDA MONKEY, HONDA GORILLA, Others , HONDA DAX70, HONDA CHALY 70, HONDA ST90 (ST90)
Commonly usable
Blinker relay of 6VMONKEY was broken, so I replaced it with this one. There is no particular problem, but the unique clinking sound of the blinker is gone, which is Minus. View detail
Fits: HONDA MONKEY, HONDA CHALY 50, HONDA DAX70, HONDA DAX, HONDA GORILLA, Others , Others 4-pole terminal RegulatorSpec. It can be widely used for vehicles.
Voltage increased slightly when running.
I bought this Regulator to review the ignition system because the MONKEY was malfunctioning. It was not the direct cause of the problem, but the original one was so old that it seemed to be worn out. After replacing it with this product, the voltage when driving went up a little. It is a little bit larger than the OEM product, but I had no problem installing it. View detail
Fits: HONDA little cub, HONDA Super Cub 50, HONDA Super Cub STD-92 (12V model), HONDA Super Cub STD-92 (12V model)
Don't expect quality.
I had a headlight unit from another company attached to my LITTLE CUB, but after more than 10 years of use, the plating was peeling, so I replaced it.
The installation itself was not a problem, but the Socket does not seem to be durable.
I installed it at the end of September 2023 and from the beginning of December 2023 the Headlight started flickering occasionally and a few days later the Headlight disappeared while driving and became completely unusable.
I suspected that the Valve was out of ballast and tried to remove it, but for some reason it would not come off. When I pulled it out by forcibly turning it with pliers, I found that the Socket had melted. The melted valve had lost contact with the valve, and the resin was further burnt.
Since the price is reasonable, I think it would be better to use OEM products like Large for Socket and Valve, with Socket and Valve as extras.
View detail
It does not fit into the other 250 models.
I purchased this for use with Blinker relay, but it does not fit into Relay's Connector.
The shape is 250 type, but it does not stick to Male terminal because the direction of the terminal is 180° opposite to Connector.
It has no use as a Connector.
This ConnectorSingle Body can be used as a Harness, but I don't think that is what a Connector is.
View detail
Fits: HONDA APE, HONDA CUB, HONDA MONKEY, HONDA MONKEY
Poorly made, poor contact
I have used it several times and it is almost certain to have poor contact.
Spring is weak, Lamp side contacts are poorly made, and terminal height is different between hi and lo.
Do not buy this product as it is completely useless and cannot be reworked.
HondaOEMSocket also has many defects, but OEM is better.
View detail
Fits: HONDA round-eyed turnip, HONDA little cub, HONDA round-eyed turnip, HONDA little cub
Please sell more solid products.
[How is it used?
I was going to order HondaOEM Product for C90 because I wanted to have a meter over 60km/h since I replaced 90ccEngine in my LITTLE CUB that I got. Discontinued. I was told that the product was not rated highly by Webike, so I purchased this product, even though I thought it was not rated highly by Review.
Did you receive the item as per the Image?
It looked OEM-like and nice...but not this.
I'm going to write udderly below, but in a way. As per your Review. The product was not good at all.
Was it difficult to install?
In the era of pure Japan production Iron CUB The wiring around the handlebar is a mess, except for the Second Type Model, which is the most common Injection, and it looks terrible.
The difficulty level is low, so please be patient and follow the Wiring and install it! (And I wrote, but I don't think you should buy it) 。
How did you like it?
Listed in Review Meter stopped working." I have not experienced any symptoms of ... I don't use it that much." It would be more accurate to say that the "new" is a "new".
First, to attach the needle Gold to fix the Meter The claw-shaped part." If you understand the role of this part, even if it is a copy product, you would understand that such a flimsy material is not good enough....
The bulbs that illuminate the inside of the meter are dark & burn out quickly, and are rarely sold at Motorcycle supply stores because they are a different size bulb than the size used in OEM meters since at least the 1990s.
Even before the bulb went out, the Meter was too dark to see at night.
I was so brokenhearted at this stage that I returned to the Normal meter, as I knew from the review that the meter was likely to stop working even more...
Was "Included Parts:" attached?
OEM Product Speed Meter Assembly Similar toQuantity:The Meter is in a Set, with the Meter content bulbs and Wiring built in.
Were there any disappointments?
All of the above is true, and it's more than half the price of what the OEMMeter cost when it was sold, but it's not a product, so it's not a product. Dumping the Gold." I used a Point that I had received in this Review section, so I didn't have to pay for it, but it left me with a feeling of emptiness that all the hard work of typing the text had been lost...
Other items that would be helpful
Point and hang of installation
As I mentioned above, the nails to stop the fixing needle Gold do not function properly, so it will be difficult to install.
[Availability and clarity of the Instruction Manual
No, if you don't know what you're talking about, don't buy it.
However, some may be confused because the color of the wiring is different from that of the OEM Product.
[Notes]
Everything I've written so far. Better not to buy." That being said, I would caution that if you are still interested in purchasing the product, good luck.
[ITEMS TO BUY TOGETHER
A used OEMMeter that you can buy for a price you won't mind paying if it fails."
Disassemble this product and OEMMeter and Quantities:2pc. Set1 (Nicoichi) If we can combine the good points of each other, we may be able to turn it into a good product. (skill & knowledge & willingness to work)
[Opinions and requests to Manufacturer
Now that the Meter for OEMC90 has been discontinued, Don't sell this product! I will not say. I don't care if the price doubles. A product that works well." to the
View detail
Fits: HONDA APE, HONDA CUB, HONDA MONKEY, HONDA MONKEY
there is a problem
However, the base material of the contact point with the Valve is the same transparent resin as that around the Connector, so there may be a problem with the heat resistance of that part, or it may have melted into a sludge and deformed, making it unusable.
The period of use was about six months for weekday commuting use.
Since the OEM was a Black resin material only in that area, I assume that a heat resistant material was used there.
I assume that this product has a delicate Spring function that presses the contacts together or the contacts attach and detach, generating heat, which the material could not withstand.
Just before the damage, the Light was on and off due to vibration.
The contact point on the Valve side had also been cut off in the shape of the Socket side terminal at the Center contact point, probably due to poor adhesion caused by the Spring function.
The spring was stiff at the time of installation, and after installation, it was as if the spring had shrunk to the point of having no stroke.
We are now using OEM and have no problems, so we have decided that OEM is the way to go, even if it is more expensive.
View detail
Recommended
Buy Plating
It's not in bad condition and I recommend it!
View detail
Fits: HONDA ST90 (ST90), HONDA CHALY 70, HONDA DAX70, Others , HONDA CHALY 50, HONDA DAX, HONDA GORILLA, HONDA MONKEY
Recommended
Inexpensive. Well made.
Recommended!
View detail
Fits: HONDA DAX, HONDA CHALY 50, HONDA MONKEY, HONDA GORILLA, Others , HONDA DAX70, HONDA CHALY 70, HONDA ST90 (ST90)
Blinker with excellent cost performance
Orange colored sphere on transparent Lens with good visibility of reflector.
Wiring is also made easy with a Bullet Type Terminal attached to the tip.
You may need to be a little careful about how much you tighten the fixing nut.
View detail
Fits: HONDA APE, HONDA CUB, HONDA MONKEY, HONDA MONKEY
No wonder the price is so low.
When I installed the OEM parts, the low beam light came on without any problem. I installed the OEM parts and the low beam lit up fine, but the spring inside was weaker than the OEM parts and the contact seemed to be faulty. I guess it is because the price is so cheap. View detail
Not exactly what it was originally intended for.
Although it is not the original purpose, the spring of the stand switch interferes with various external parts installed, so I bought it to let it go.
It can be used just fine when co-tightened in the Footpeg Bracket hole under the Engine.
View detail
Fits: HONDA dachshund, HONDA Shirley 50., HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA Shirley 70
quality for the money
I purchased this product to use as a multi-reflector, but when I received it, there was an error in the dimensions of the Rim and Lens, so the Lens was uneven and there was a gap between the Rim and Lens. Also, the positioning protrusion of the Valve insertion part has a gap, which seems to be fine for Halogen bulbs, but when the LED Valve is installed as it is, it is tilted against the pattern of the reflector.
So I managed to install it by modifying it in various ways. I think the quality is good for the price.
View detail
The entire Cylinder is out, so replace it with a new one!
OEMIgnition switch in tl50 is rotting away.
When you get it, Plastic in the Ignition switch is
It's cracked due to deterioration and the whole Cylinder is missing.
I have 4 Wiring, so I'm looking for a Honda4mini 4 Wiring.
I purchased this product
It will be diverted to →tl50 for CUB.
The shape of the coupler is different, so it's not a simple matter of just popping it on.
Kindly note that Wiring is the same color as OEM, so it's easy to tell!
I measured the length from the Ignition switch to the 6V MONKEY/GORILLA Main Harness, cut it off at the same length and installed it with Bullet terminal connection!
The feel when you turn the key with the pusher is brand new!
I'm so glad I'm not the only one!
Spare key is also included, so this will work for the time being (lol).
Useful for Repairing an old Honda4mini!
View detail
as necessary
I bought this to attach Meter to a CUB I am creating.
When I installed it, I wondered if the NLamp's wiring was +Control, but the CUB's wiring did not light up, so I used a quick output Conversion Harness to deal with the problem.
I was concerned that the high beam lamp was too bright. The trip meter knob fell off and went missing during the test run, but I don't care.
View detail
Approximately six months after purchase, the
About six months after purchase, the Meter's display light stopped working due to poor contact.
Furthermore, during touring, the Knob portion of the mileage meter is removed and the meter number cannot be reset.
We plan to replace it with a new one from another Manufacturer.
Complete shoddy product, no recommendation.
View detail
I put it on cb400ss.
Is it a problem with Engine Displacement Volume? The actual speed and Meter are messed up. This will not pass inspection. I can't use it. View detail
Fits: HONDA Super Cub 50, HONDA little cub, HONDA Super Cub STD-92 (12V model), HONDA Super Cub STD-92 (12V model)
I'm just...
When first installed, Lo did not light up.
Switching Valve to something else did not help.
I switched back to the NORMAL terminal and it was perfect.
The rest of the Screw holes are slightly out of alignment.
Well, because it looks good.
View detail
Fits: HONDA APE, HONDA CUB, HONDA MONKEY, HONDA MONKEY
It was damaged after 8 months of use at 4000 km Meter.
I purchased it because it was less expensive than OEM Parts, and installed it. However, the gold material at the contact point with Valve melted, and I could not use it after 8 months. The cause is unknown, so I will purchase again. View detail
Fits: HONDA MONKEY, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
Three stars because I don't know the OEM.
I bought a used MONKEY, can't say for sure since I don't know the OEM shape of the color, but I thought it was well made. View detail