Reviews
Fits: HONDA DAX, HONDA CHALY 50, HONDA MONKEY, HONDA GORILLA, Others , HONDA DAX70, HONDA CHALY 70, HONDA ST90 (ST90)
Commonly usable
Blinker relay of 6VMONKEY was broken, so I replaced it with this one. There is no particular problem, but the unique clinking sound of the blinker is gone, which is Minus. View detail
Fits: HONDA DAX, HONDA CHALY 50, HONDA MONKEY, HONDA GORILLA, Others , HONDA DAX70, HONDA CHALY 70, HONDA ST90 (ST90)
Blinker with excellent cost performance
Orange colored sphere on transparent Lens with good visibility of reflector.
Wiring is also made easy with a Bullet Type Terminal attached to the tip.
You may need to be a little careful about how much you tighten the fixing nut.
View detail
Fits: HONDA ST90 (ST90), HONDA CHALY 70, HONDA DAX70, Others , HONDA GORILLA, HONDA MONKEY, HONDA CHALY 50, HONDA DAX
Parenthesis is nice in chic shades, but …
[How is it used?
I wanted to change to an old car style headlight, and on the other hand, I wanted a multi-reflector type headlight, so I purchased this headlight, which was also inexpensive.
Was the one you received as per Image?
As you can see in the Image, the Headlight is a Beauty.
Was the installation difficult?
Just by replacing the original Headlight, the Lens can be removed with 2 Screws and the Body can be removed with 2 Screws on the Bracket, but it is Large strange to have to redo the Wiring.
I am patient and persevering, thinking that I won't have to change it so much.
How was your experience with it?
First, it is clearly brighter than the NORMAL and KITACO Headlight.
Visibility is good and I can drive safely at night, partly because I switched to a high-efficiency Valve.
[Included Parts:were they on?
Valve included.
[Was there anything that disappointed you?
There are three disappointing Points.
The first is that Light case is Material:Since it is plastic, vibration shattered the holes in the Rim mounting Screw.
Second, the light lens is turning yellowish due to sunburn.
Third, the plating part is prone to rust, and if you do not keep polishing it, you will not be able to remove the rust.
I ended up replacing the light case, but I am thankful that there are Repair Parts for the case only.
View detail
Thank God Repair Parts is there!
[How is it used?
I wanted an old car style Multi Reflector Headlight, so I bought a Black Type Headlight, but the Screw hole in the Rim was shattered by vibration, so I bought it as Repair Parts.
Was the one you received as per Image?
I changed to Plating for a change of pace, but it is shiningly good and parenthesis is good.
Was the installation difficult?
No way, no way, no way. After redoing Wiring many times for the third time, I was able to connect Wiring without having to leave a picture of it anymore.
Please do not imitate if you are a first timer. (Lol)
How was your experience with it?
It is a good Headlight, brighter than the NORMAL and KITACO Headlights.
However, I think the Case is made of plastic and is weak.
[Included Parts:were they on?
Unlike the HeadlightAssy, nothing is included.
[Was there anything that disappointed you?
There is an unfortunate Point that has not changed.
The first is that Light case is Material:Plastic, so it will eventually crack from vibration.
Second, the quality of the plating on the case is poor and will become dull after use, so it must be polished.
▼ So far, but I have managed to keep it without cracking. If it cracks next time, I'll switch to something made of Gold, although Rust will continue to plague me…
View detail
Diversion to 6VCHALY
Used to convert 6V square eye CHALY to round eye.
There was a gap between the OEM Meter and the Meter, so you may be able to use the Meter Rubber from Minimoto to hold the Meter in place. I used 3DPrinter to make the color.
The Valve of the Headlight is a shape that I have never seen before, and I built in Marshall's Headlight because both Reflector and Lens are Plastic. I made a bracket with 3DPrinter and fixed the bottom two points with screws.
CaseBody was solid, not Plastic.
View detail
Fits: HONDA LITTLE CUB, HONDA Super Cub 50, HONDA Press Cub 50
well bought
I bought it overseas for repairing my love Little Curve, which I have had for nearly 10 years. I had all the parts I needed, and various parts are also on sale, so it was very tasty. I am still installing, but the picture and product are the same~ It's also very fast^^ I bought it overseas for repairing my love Little Curve, which I have had for nearly 10 years. I had all the parts I needed, and various parts are also on sale, so it was very tasty. I am still installing, but the picture and product are the same~ It's also very fast ^^ View detail
Fits: HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA SUPER CUB 50PRO, HONDA SUPER CUB110PRO, HONDA SUPER CUB110, HONDA SUPER CUB 50
without a problem
Because it is only Coupler and the electric wire, I thought that even if I choose an expensive commodity, I chose this commodity which was cheapest. It is OK to install without processing, and I can use it without a problem. View detail
I bought this to install my Mini Blinker.
Installation is very easy as long as you have the Bolt and Nut to hold the Bracket in place. It would be great if the mounting holes were long enough to allow you to adjust the width a bit! View detail
Fits: HONDA MONKEY, HONDA GORILLA
Is good
Chosen to build MONKEY from scratch
Here are my thoughts on the assembly
The Rubber cover of the Light back is quite large and hard
This pushes the meter cable considerably and makes the meter itself float
It doesn't look good as it is "Cut the bulb wiring terminals short and re-solder them The "Rubber
I "Cut the bar short" and it fit in nicely
The meter is installed in the form of pulling and holding the meter at one point with spring, so the inside of the meter can be used The non-drawn side may float, as it is vulnerable to the force pushed from
(Not in comparison, as I don't know if the OEMs do.)
Harnesses fit neatly and there was plenty of space for them
If you can modify it yourself, it's a good cosmetic and first choice ; I think
View detail
Fits: HONDA Shirley 50., HONDA Shirley 70, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA Dax 70, HONDA Dax 70, HONDA dachshund, HONDA dachshund
I think it's cost effective
I bought it because I was taking care of my GORILLA and I was concerned about the rust in the rim section Some structures are different compared to the Product (upper inner Rim, lens positioning) Plating is beautiful and I like it! View detail
Fits: HONDA GORILLA, HONDA MONKEY
Quality is what it is
Although I removed the vinyte between Harness to extend part of the wiring, the Earth branch is not a good idea Crimp in RoseRose is now sweet and RoseRose
It doesn't matter if you don't do any extra processing
Also, it would be helpful to have a Wiring diagram, but the CDI⇔Engine Wiring color is wrong
View detail
Fits: HONDA round-eyed turnip, HONDA little cub, HONDA round-eyed turnip, HONDA little cub
OEM Shape and easy to read
If you are an OEMMeter, you can't read the meter because it's Bore up It's very easy to see, but since it's an OEM shape, you have to look at it carefully to see that you've replaced it It is View detail
Fits: HONDA Super Cub 50, HONDA Super Cub 70, HONDA Super Cub 90
For CUB ...
I put it on CUB 90, but it is normal and it is normal without permission.
If you do not do Clear blinker, you do not need Orange balls ...
Rather, I wonder if there is an ordinary ball of VERSION.
I have a ball I did not use as Spare.
View detail
Fits: HONDA SUPER CUB 50, HONDA SUPER CUB 90, HONDA SUPER CUB70
It arrived quickly. Purchase with CUB 90 reserve
I have not used it yet, but I think Cospa is good.
It is put in the Rear box with entering PetitPetitVinyl as it is sent.
Reliable feeling increased.
View detail
Good quality headlight
Very happy with this headlight. It's bigger than the Dax 6V type and I think it fits the bike perfect. The metal and paint-job is still flawless after a Norwegian winter. I changed the bolts and added a visor to make it a little more fancy. View detail
Fits: HONDA Shirley 50., HONDA Shirley 70, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA Dax 70, HONDA Dax 70, HONDA dachshund, HONDA dachshund
3.6
When fixing Rim and Case, the position of the Screw hole did not match a bit.
I could install it with a little processing.
As a result, I think it was good.
View detail
Diversion to PCX 125
I diverted Blinker of PCX 125 and Horn to reverse it. It was a bit small, but it worked. I cut off the rotation stopper's patch. Starter, Stop-lamp Wiring remains intact. View detail
Diversion to PCX 125
I diverted it to reverse the position of Blixer and Horn of PCX 125. It was a bit smaller than OEM's, but it went well.. I also searched for other things, but I think that it is easy to divert this unnecessary Wiring. View detail
Fits: HONDA little cub, HONDA Super Cub 50, HONDA Super Cub STD-92 (12V model), HONDA Super Cub STD-92 (12V model)
Pon attachment, but no overstock is a thing
Please remove the OEMHead and see it for a while and check the structure.
For some reason I replaced the headlights with ChicaChica in a week and touched poorly!
Lock ConnectorASSY as soon as it is removed (Y-shaped groove) It seems that Hayato was sweet.
It was the cause of failure that I bought it and put it as it was.
The way to buy from now on, once you remove ConnectorASSY and Valve & Head, restart and lock it again I think that there is no mistake like me.
Since Harness is hard, care must be taken not to pull Wiring when removing OEM or when replacing it.
CUB Why should Harness be made sturdy, but once.
The appearance is Blue eyes and it is a good feeling.
View detail
A key set can be exchanged at a low price
Very satisfied because you can exchange a set of keys at a low price. Construction is not bad, installation pitch etc is no problem. There is a bit BALI in the resin part of the key, but it can be reworked with Cutter. Overall very satisfying. View detail