Reviews
It is easy to use
I bought it for Point and Tappet maintenance.
The 0.02mm was crumpled. It seems to be able to stand up to use somehow, but I wondered if this was a bad idea, even though it is a cheap one.
The oil-covered point is also annoying because it takes some time and effort to use.
Nevertheless, the cost performance is excellent, the measurements cover a wide area and the shape is very easy to use.
It's worth the price. It seems to be a problem for simple maintenance.
View detail
To adjust valve clearance
I bought it to adjust the Valve clearance on my ELIMINATOR 250
The EX250 Engine, which is also used in the current NINJA and VERSYS, is a mature engine After 60,000km, it started to make a nasty noise when idling and clattering
Thanks to this Gauge, it's now perfect and in good shape The size you need is not exactly the same as the size you need, but if you stack them up, it's not a problem Not at all
If I had to say, it's a little bit wide, so it's hard to get into the narrow IN cams, etc I even had a thought
Even TWIN is like this, so when you fiddle with InlineFour and other products, a slender, separate product You might want to choose
View detail
It's cheap!
It is used for Tappet clearance of GORILLAetc.4CycleEngine and I have
The price is low enough to save me a lot of money because I can't use it to measure Clearance because it gets worn out gradually
The gauge is made of a large size, but the gauge is made of a fixed metal clasp GORILLA, it's hard to use for MONKEY, so Size is stamped on it, too, so I'm going to have to make a stop If I remove it and set it to RoseRose, I can use it by shifting the position 4 or 5 times I am!
View detail
good
It is cheap and has high Cost performance. 1pc. If there is one it is an organism. I think that it will not be damaged by buying it. Tappet adjustment etc etc. I tried to use it for purchase. There were 23 peas, even if the car type changed, I bought it without any problem and I thought it would work. View detail
Tapered shape is Good
Motorcycle's Tappet is in the back, and the usual rectangular Thickness Gauge is hard to use. This product is superior to that point. However, it was somewhat disappointing that the thicker thing is slightly out of the Size range I would like to use. (I felt that I wanted Shift to a slightly thinner side. ) Naturally, it is essential to choose a Set whose thickness you want to use is covered beautifully. View detail
It is a required tool
I bought it to make Valve clearance adjustment
It's easy to use because it is set finely
While paying attention not to rust, I would like to use it for the Large thing
View detail
Used for CUB90DX
Tappet sound has become considerable, so I tried to adjust and bought it.
Thickness Gauge was what I felt,
Tappet Looking at the site of the person who is adjusting, it was a tool to measure Clearance.
It was truly amazingly fluent and something like a plate, thought that I should use it like this.
This time 0. It is the use of 05 mm.
Since it enters in a bent state, it was easier to work than I thought, but since it is fluent at all, there are traces left when I tightened.
The price is not so expensive, I felt that Torque had uped when I adjusted Tappet, so I made a rating of 4.
View detail
[Webike Monitor] Since a product besides has not been used, the comment about ease of use is not made, but it can use ordinarily. It is a conclusive factor of purchase that there was 0.13 used by Motorcycle to own. Although there is much
[Webike Monitor] Since a product besides
has not been used, the comment about ease of use is not made, but it can use ordinarily.
It is a conclusive factor of purchase that there was 0.13 used by Motorcycle to own.
Although there is much
number of sheets, since there is 2 or 3 number of sheets used at present at most and there is, it does not think that it was profitable. [ much ]
It expects to be
, however to be useful some day!
View detail