Reviews
Each person has his/her own preference.
I prefer it without the Bikini cowl, but I finally installed it because I could not stand the wind pressure when driving at high speeds.
I chose this product because I thought that if I was going to put it on, it should be a proper one, not a Universal or something like that.
As expected of an exclusive product, the color and fit are perfect.
And the Style after installation is not bad. I guess it's a matter of taste, but I thought this was the way to go.
The windproof effect is quite good. The area below the chest and shoulders is almost free from wind, so high speed driving is possible.
It became easier. However, the wind is now concentrated near my face, so it depends on the Jacket I am wearing.
Wind Cutting noise has become louder.
I wish it had One point, Line, etc. because the colors are monochromatic.
View detail
It's still good!
Installed on a 2023 SpeedTWIN1200.
I had no choice but to purchase a 2019 MODEL Bikini cowl, as there were none available on the market that corresponded to the 2023 model year.
The quality and style of the product after installation are satisfactory, although additional work is required to cut out some parts for installation due to the different year. However, I am satisfied with the quality and the style after installation.
View detail
For cold weather, a little.
I bought it because I don't want to use an electric heating system. I drove on a normal road with little traffic at the speed limit with an outside temperature of 5 degrees Celsius (I felt 0 or −1 degree Celsius?!!!). I drove at 5 degrees Celsius (0 or −1 degree Celsius?!) on a normal road with no traffic, but my fingertips started to feel cold after about 15 minutes and it was limited to about 1 hour. I thought that the square shape of the underside of the Shield would keep my fingertips cooler. I thought the shape of the underside of the Shield could be improved.
I thought I also needed a Grip heateretc. as it is impossible to run in winter with just this.
Also, it is better to tighten the screws on the Shield a little with a tool. The Instruction Manual says to just tighten it by hand to the point that there is no wobble, but when I was running, I started to hear a banging noise and noticed that the screws were loose and Oversized, so I stopped and tightened them.
Because it is not a Type that is attached to the Bar End, it could be operated without Stress when releasing the hand from the Handlebar when stopped.
View detail
CHIC DESIGN Road Comet Head cowl
About quality and texture Soild plastic made with the cowl itself and the wind shield About the feeling of use Looks great as I bought the Diablo black paint. The paint is similar as my yellow ball SE version I'm able to fit my Doremi Z2 signal lights. Difficulty of installation Less then 20 mins. Easy to install. I do not need to change my brake bracket as I'm already using Galespeed brake pump. Cost performance and comparison with other products. Great price with painting. Plastic is soild too for the price. About shipping and packaging Shipping is expensive as the item is big but it comes with its own box well wrap. Any concerns, cautions, or advice when purchasing. The top wind screen will be a bit vibranting if traveling in high speed. But bearable and stable enough. I went to a decal shop to install the similar design as the brand to save a bit of cost. Not perfect but still looks great View detail
I tried to be a human pillar.
I just installed it.
It is still too hot to ride.
I was sweating just installing it.
I thought this one was cooler than the Bikini cowl by the same manufacturer, which has many reviews, so I bought it even though there are no reviews of the product.
I didn't mind the SIDE design etc. and thought it was definitely better looking in person than in the Site photo.
To install, remove the light lens, and then fasten it by playing with the bolt that supports the light case?
Here, when the Bolt is tightened from the outside of the Cowl, the Cowl is slightly dented, but I think it is Spec.
Next, fasten the bolt on the back side of the Horn, which is a challenge unless you have good dexterity.
I will post photos for your reference if you are considering it.
View detail
It was not bad.
The Instruction Manual was a little confusing, but I managed to put it on.
Luggage Hook and Fender holes did not match and had to be cut out with File.
The finish is perfect.
I like it.
View detail
I still like Design!
Purchased with FFender.
Just by attaching this Series, the old car feeling is heightened, so the satisfaction is high.
Difficulties during installation - use are as follows.
Paint surface is thin
→milliOrder is not thick enough, so it peels off quickly. beware of Bagetc. gapping and hitting.
Made by FPR
→ I'm a little scared of the crackling sound it makes during installation.
I would like to see something made of steel in terms of texture.
In addition, the Bolt mounting holes on the Engine side are removed from the molding die.
Due to the slight shrinkage, it was difficult to install.
Tail lampReverse side is scuffed.
→ It may not be a problem if you don't ride in the rain, but I think it may be the cause of water accumulation in the Lens.
At least a separate body or lid would give me peace of mind...
BlinkerWiring without Hole next to Number mounting
→Side bag is attached, so it could not be attached in the OEM position, so it was installed with the Small modification.
It is not that difficult, and the Blinker itself is matched with the Number in the Bracket.
Positioning can be done roughly, but it doesn't matter.
Wiring is fixed with Wiring Fixing Material for Vehicle.
View detail
Satisfied with windproof performance
Purchased because my hands get cold when the wind blows and it is hard to drive.
Since it is model-specific, installation was easy without modification.
View detail
It is highly functional as a windbreak.
[How is it used?
I purchased the car because I was often touring far away from home and often felt scared on the highway in strong winds.
Was the one you received as per Image?
It was larger than the Image and was well made.
Was the installation difficult?
The installation itself was easy, but fine tuning to prevent interference, etc., was difficult and took a surprisingly long time.
How was your experience with it?
It is excellent as wind protection. On windy days in particular, I can now ride so stably that I can hardly believe it is the same Motorcycle.
[Included Parts:were they on?
Screws and Instruction Manual are included.
[Was there anything that disappointed you?
The Large Screen eliminates the old car look and makes it difficult to decide whether to go for functionality or style.
▼The angle can be adjusted to some extent, but due to interference, I felt it was not very flexible.
Note that OEMNavigation cannot be attached at the same time.
View detail
Rear Fender Short
I felt the CB1100 was a bit heavy in the back (I guess it depends on the Custom direction).
Generally I am satisfied, but the price is still too high.
The plating is uneven.
Installation was a snap and easy.
View detail
It is solidly built
Installation is also a simple matter of replacing the Headlight Bolt with the supplied Bolt and installing the Bracket next to the Horn to make it fit.
The position of the reserve tank was changed to a universal bracket because the handlebar had been replaced with a BEET taper handlebar and the included bracket would have come in contact with the cowl.
Cowl has no complaints at all, the paint is in good condition.
No rattling and no chatter noise at high speeds.
However, there is some tampering from wind pressure, but it is acceptable.
View detail
L size was chosen although it wavered in medium size and L size.
L size was chosen although it wavered in medium size and L size. View detail
Road Comet
I ordered one for my Z900RS and it took me 4 months to get it, the design is perfect but some of the details are a little rough, which is a little disappointing. I made it by myself. The windproof effect is limited, but it makes a LARGE difference. I am looking forward to long touring in summer. View detail
Performance is adequate.
I bought it for winter protection in the Kanto area and never froze when used with winter Gloves, which are not that thick.
Installation is also easy, as long as the RightMirror is co-tightened with the Mirror and the RightMirror has an Opposite Thread Screw.
The Bracket is solid and the Screen is strong enough to touch.
As is the fate of the SR400, the engine vibration is fine but shaky.
View detail
Fits: その他 , YAMAHA SR500, YAMAHA SR400, SUZUKI ST250, SUZUKI VOLTY, KAWASAKI W650, KAWASAKI W400, KAWASAKI ESTRELLA
Used for MeguroK3
Classic fenderFront from the same manufacturer (WW-FF1GEL) It was used in conjunction with
Holes were drilled using a method that came up in a Net search, using masking tape.
The gap between the thickness of the Plate and the Bracket is not Exactly, so the Plate moves around when assembled properly.
If you are concerned about this, you should twist the Bracket to assemble it, or adjust it by collapsing the gap between the Bracket.
Plate will peel off color quickly during assembly.
View detail
Fits: KAWASAKI W800, KAWASAKI W400, KAWASAKI W650
Used for MeguroK3
Made of FRP.
The position of the mounting holes is correct, but the width from RightFork to LeftFork and the width of Fender are not Exactly, so it can be installed as it is, but it may be necessary to put a Spacer in between.
The top of the Fender hits the Fork, so if you are concerned about this, you may want to use a hit stop.
View detail
Fits: KAWASAKI W800
Used for MeguroK3
Made of FRP.
It can be assembled as it is, but the fender orientation will not match and there will be a gap in the mounting area.
If you want to install it securely, you need to temporarily assemble the later Bolt, align the Fender orientation, and then check the position of the holes in each section before expanding the holes.
Also, a gap of about 3mm will be created in the upper mounting area, so a spacer is required.
As you can see in the product image, there is only Fender and Tail lamp.
We need to think about Blinker.
View detail
I think Quality is great!
I bought it on the spur of the moment because only Surfacer paint was in stock.
As expected from a manufacturer famous for its Bikini cowl, the quality is good. I was able to put it on easily and efficiently.
Since there is no bracket where the screen extends, I was worried that it might flap at high speeds, but it was no problem at around 100 km/h.
I didn't have any problems using it, but I removed it because I preferred a round shape with more rounded corners, so I thought something was different.
View detail
Fits: HONDA Rebel 500, HONDA Rebel 250, HONDA Rebel300, HONDA Rebel300
It does not catch the wind.
I was worried about how it would look when I put it on my SE because the only product image I could find was the Normal version of the Rebel, but it matched without any discomfort.
As for performance, I used it with Warm Gloves and Grip heater on my winter commute to work, and I didn't feel any wind hit me while driving, so I think it is effective.
Also, the lack of wind did not reduce the efficiency of the Grip heater, so it felt warmer.
View detail
CHIC DESIGN Masker Load
It fits perfectly.
There is no difference between the paint and the body color, and there is no sense of discomfort.
As for aerodynamic issues after installation, I haven't driven on the highway.
I don't know the effect, but I think the wind hitting the Helmet is less.
Total and it is a very good product.
View detail