Reviews
Damage Insufficient strength for Classic Bike and Large type Blinker
Used for Blinker relocation to install Side carrier on W650.
Blinker will be made by Inadme, a standard W-riding product.
Mountability
Instruction Manual is not included, but since it is Simple, it only attaches where it should as a shape.
If you have done electrical Custom before, there is no problem.
・Design
The reverse side is hidden by the bracket, but it is a nice, clean design.
Functionality
The Blinker root attachment is hidden inside the Fender,
For Type with a short Blinker length, care should be taken so that the Lens is not hidden by the Number.
Quality
Two months after installation, at a mileage of about 1000 km, the bracket bent part snapped off.
As it occurred while driving, a Blinker hanging by Harness was caught in the Tire,
I was sandwiched between Swing Arm and Tire.
Luckily, the Tire did not lock, but one wrong move could lead to a heavy Large accident.
If it is a Plastic lightweight Blinker, it may be no problem, but if it is a Classic type
If there is a possibility of installing a Blinker, this product is not recommended.
Since these parts are installed near rotating objects, component failure can lead directly to accidents.
Please be careful not to lose money buying cheap goods.
View detail
Mounted on Classic fender
It was installed on the company's Classic fender.
As shown in the image, the odd shape is due to the shape to match the Classic fender.
Unlike a typical blinker bracket that is co-tightened with the license plate, the blinker mounting part goes to the back of the number about 40mm on the One Side.
Care should be taken when installing short Blinkers.
In this case, we used the OEMBlinker as it is, so we are satisfied with the Refreshing attached more than we expected.
View detail
Fits: HARLEY-DAVIDSON Universal, HARLEY-DAVIDSON DYNAFamily, HARLEY-DAVIDSON SPORTSTERFamily
I was able to install it successfully.
Before my 883 Iron was delivered in April, I had been thinking of installing a Bikini cowl from CHIC DESIGN's TEERAEarly sometime after I bought the car. However, the price was too high and I was worried for 2 months, but I decided to buy it. I'm sorry, but because of the price, I bought the Body at another store instead of WEBIKE, and I only bought the Lowdown Kit because there was a Point here. I had to adjust a lot of things to install the body, and the instruction manual was not very well written, so it was hard to understand, but I managed to install it. I think the price is about half the price of the others. The stuff is good. View detail
Fits: KAWASAKI W650, KAWASAKI W400, YAMAHA SR500, YAMAHA SR400, Others
Beautiful modeling, it goes well with NORMAL.
The standard Tail lamp.
The Lucas tail lamp comes in two sizes, Large and Small, and I chose the Large.
You will need to drill holes in the Fender.
good point
It can be attached to Normal fender. Even if the other fender is Normal or Lucas tail lamp, you can get the atmosphere of old car.
Visibility is high. Also passes vehicle inspection.
Design that never gets old.
Since it is FRP, it can be repaired by Acetone even if it breaks.
A bad point
It's safe, so it doesn't show any particular personality.
I've also been using this Tail lamp for a long time.
I never get tired of it and it looks good in any Style.
Products that have been sold for years, products that everyone loves.
I think I'll keep using this for a while.
View detail
Fits: KAWASAKI W650, KAWASAKI W400, YAMAHA SR500, YAMAHA SR400, Others
The construction is crude
Tail lamp part's screw hole and FenderMounting Bolt hole are not horizontal No slant! It's disappointing that it looks like an amateur drilled a hole in it without taking measurements beforehand View detail
Fits: HARLEY-DAVIDSON Universal, HARLEY-DAVIDSON DYNAFamily, HARLEY-DAVIDSON SPORTSTERFamily
[a webike Monitor] -- -- any problem cannot be found -- the completion of wearing. Although it is Beauty goods, if a Cowl is attached, it will completely disappear.
[a webike Monitor] --
-- any problem cannot be found -- the completion of wearing.
Although it is Beauty goods, if a Cowl is attached, it will completely disappear.
View detail
Fits: HARLEY-DAVIDSON Universal, HARLEY-DAVIDSON DYNAFamily, HARLEY-DAVIDSON SPORTSTERFamily
It purchases in order to equip with the bikini cowl of a chic design. Although-izing of the headlight can be carried out [ lowdown ], even if this single article uses, there is no unusual impression in appearance. Since he would like to make KASUT
It purchases in order to equip with the bikini cowl of a chic design.
Although-izing of the headlight can be carried out [ lowdown ], even if this single article uses, there is no unusual impression in appearance.
Since he would like to make KASUTAMU others, the purchase purpose will be bought.
View detail
Fits: HARLEY-DAVIDSON Universal, HARLEY-DAVIDSON DYNAFamily, HARLEY-DAVIDSON SPORTSTERFamily
2006 model XL883L was equipped. Attachment is easy. The circumference of a change headlight feels appearance refreshed very well. He stuck together with the blinker stay of KIJIMA.
2006 model XL883L was equipped.
Attachment is easy.
The circumference of a change headlight feels appearance refreshed very well.
He stuck together with the blinker stay of KIJIMA.
View detail
WM bolt-on lucas type The tail lamp kit was equipped. The number plate is removed so that it may understand with a photograph. Although a rear blinker is pure, it is the touch which comes out outside a plate somehow. Even if it carried out sim
WM bolt-on lucas type The tail lamp kit was equipped.
The number plate is removed so that it may understand with a photograph.
Although a rear blinker is pure, it is the touch which comes out outside a plate somehow.
Even if it carried out simultaneous wearing with the above-mentioned kit, a fender was not contacted, but wiring will appear with CHIRATSU.
Stay is firm goods.
View detail
Since the blinker screw hole of stay suited the portion in front of the both ends of a number although the blinker was already transferred to the rear number portion, when the blinker was attached, the screw of blinker stay had protruded considerably hori
Since the blinker screw hole of stay suited the portion in front of the both ends of a number although the blinker was already transferred to the rear number portion, when the blinker was attached, the screw of blinker stay had protruded considerably horizontally.
Since are a thing of L shape purchased in the home center, it was able to substitute, and the lug was able to be suppressed, since it was slightly awkward, but right and left were not connected, it was sweet, and fixation also needed to retighten the screw thread frequently and was troublesome.
.
This stay was attached to the just right location, without the blinker which he is using protruding, since the screw hole was considerably settled inside from the number.
Since a number is fixable firmly by a bundle type, the blinker location was also stabilized and has been satisfied.
It is glad that the screw and the washer are also attached.
It purchased and was a correct answer.
View detail