Reviews
Fits: HONDA CBX400F, HONDA CB400SF, HONDA CBR400F, HONDA CB400FOUR, HONDA CBX400F, HONDA CB400SF, HONDA CBR400F, HONDA CB400FOUR
Exhaust manifold Gasket
I chose the cheapest one and it was perfect - no problems and no gas leakage. View detail
Fits: HONDA CBX400F, HONDA CB400SF, HONDA CBR400F, HONDA CB400FOUR, HONDA CBX400F, HONDA CB400SF, HONDA CBR400F, HONDA CB400FOUR
Made by POSH for safety!
I always used KITACO but this was cheaper so I bought it.
Compared to KITACO, it is the same as KITACO Large and seems to work fine.
View detail
Fits: HONDA CBR1000RR, HONDA CB1000 SUPER FOUR (Big One), HONDA CB1300 Super Four, HONDA CB1000 SUPER FOUR (Big One), HONDA CB1300 Super Four
When replacing the Exhaust System of CB1100etc!
[How is it used?
When we replaced the Exhaust System, we had to replace the Gasket as well, otherwise it would leak and cause power down.
How was your experience with it?
It is designed for CB1300, but can be installed on CB1100 without any problem.
Of course, the quality is fine and can be used without disposal leaks.
How did it compare to other products?
The cost performance is good because it is cheaper and of higher quality than OEM Product and KITACO's same etc. products.
[Points to note]
Note that if it has not been replaced for a long period of time, it will stick to the Engine side and scratch it if not carefully removed.
To prevent waste leakage, replace the exhaust system with a new one even if it is troublesome.
View detail
Fits: KAWASAKI GPZ750R, KAWASAKI GPZ900R, KAWASAKI ZRX1100, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZX-12R, KAWASAKI GPZ750R, KAWASAKI GPZ900R, KAWASAKI ZRX1100, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZX-12R
Posh Exhaust Gasket
I used it on my GPZ900R.
The price was low and it worked fine.
View detail
difficult to install
It was difficult to install and tore during installation. View detail
Essential for maintenance and custom
[How is it used?
I used it to fix the hose and thermostat on my YAMAHA XJR400R. I also use it to put together the wiring of the electrical system and others.
How was your experience with it?
It comes in a 100-pack, so it is quite easy to use.
Also, a wide variety of colors are available so that you can use the color of your choice.
Personally, I don't like Custom's conspicuous in-hemp palmock, so I would choose Black, but I think it would be useful for electrical systems if you use a conspicuous color inside the car body or in other places where it is not visible.
How did it compare to other products?
You can buy them cheaply at 100-yen stores or home centers, but since weather resistance is important for motorcycles, you can trust POSH's products.
[Points to note]
Be careful not to cut them with a piece of paper.
View detail
useful
The material is soft and comfortable, and my fingers stay cool even in the middle of winter, so it is very useful. View detail
To combat the cold.
I use it every year to prevent my hands from getting cold from leever. View detail
Finger-friendly
The grom is Black and I wanted to add color.
Lever grip so it was a simple Accent.
I was just worried that the tip of the lever might shred when I installed it, but I was able to install it successfully.
It was Point to apply a generous amount of detergent when installing.
View detail
Fits: HONDA Super Cub 110, HONDA SUPER CUB 110
Recommendation to those with Small hands!
SUPER CUB110 (JA44) The OEMBrake lever is comfortable to hold, but the hand Small (short fingers) It is a somewhat distant position for me.
OEMLever is not an adjustable Type, so I was looking for one and found this product and bought it.
For the same reason, I installed it prior to the CROSSCUB110 and found it very easy to use, so I guess it would be a Repeat purchase.
Lever1 I am a little hesitant because of the price, but the quality of the product itself is very good, and above all, I am convinced of the comfort of the product after using it.
Since it is a part that is constantly touched while driving the Motorcycle, the cost per ride time is probably very small.
Installation is simple as a mechanism, but it takes a surprisingly long time, including removing the Cover on top of the Handlebar.
I broke my customary claw when removing the Cover:....
If you are clumsy like me, I think it is safer, cheaper and faster to leave the work to Shop ^ ^ ^.
In general, this is a very Recommendation product for those who complain that the Brake lever is too far away.
View detail
Fits: HONDA ZOOMER(Ruckus), HONDA ZOOMER(Ruckus), HONDA TODAY, HONDA TODAY, HONDA SMART DIO, HONDA SMART DIO
When replacing the Exhaust System
[How is it used? Used for ZOOMER
Was the one you received as per Image? Yes
How was your experience with it? no problem
[Points to note] There is none
How did it compare to other products? I think it's a good product.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
Effective for hand Small saiRider
Honestly, if the price of the Brake lever1 pc.
I think it is very expensive.
Still, I was right to replace it.
Brake lever of CROSSCUB110 because my hand is small
It was difficult to operate due to the remoteness of the
OEMs are levers that cannot be adjusted, and inexpensive for replacement
The OEMs are all in the same position as the OEMs.
The replacement work is simply to remove the Bolt and Wire that serves as the axis.
It is very simple:Wire on the front drum side.
It is best to do this after loosening the
After the replacement, the feel is Outclassing better!
Quantity of index and middle fingers:2pc seating in just the right position.
The following is a list of the most important items.
Not having an unreasonable hand position is the key here when driving.
I did not expect to feel as comfortable as I did.
Since it is an expensive lever, be careful not to fall and break it.
I would like to ride with it on!
View detail
Fits: KAWASAKI EX-4, KAWASAKI W400, KAWASAKI W650, KAWASAKI W800, KAWASAKI EX-4, KAWASAKI W400, KAWASAKI W650, KAWASAKI W800
no problem
I used it on a W650 assembly pipe and it installed without any problems. View detail
Power Filter Replacement
Installed on Z125PRO
The DAYTONA Power Filter had various problems, so we installed a new Duct and installed this one!
I am satisfied that there is no more noise to worry about.
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA Ape 50, HONDA Ape 100, HONDA Ape 50, HONDA Ape 100
Better than expected.
I bought it because I wanted something cheap and from a reliable manufacturer. View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA Ape 50, HONDA Ape 100, HONDA Ape 50, HONDA Ape 100
Install on PC20
I bought it to install it on my friend APE100 DAYTONA PC20 Carburettor, but now I can't install it because it has a lot of pollen and P.M25, so I'm thinking about installing it in the fall. ------------------------------------------------------------ ---- I bought it to install it in a friend APE100 Daytona PC20 Carburettor, but now I can't install pollen and P.M25, so I can't install it and I'm thinking about installing the season in the fall . Powered by Google Translator View detail
I like that the terminals are Straight.
[How is it used?
For Headlight H4 Harness processing
Was the one you received as per Image?
Yes
Was the installation difficult?
The terminals are Straight, so I was able to Crimp with the tools I had on hand.
How was your experience with it?
Satisfied
[Included Parts:were they on?
CouplerBody and terminals only
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Flag terminals, which are common on H4Couplers from other manufacturers, are difficult to crimp without a special tool, but these are Straight terminals and can be used with standard Electric Works Pliers.
View detail
Fits: HONDA GORILLA, HONDA MONKEY
It works normally
Used for Headlight of MONKEY.
It's this cheap but installs without any problems. Durability is also not an issue as I've been using it for a few years now.
View detail
Excellent oil resistance
I used this hose for the fuel line from the fuel tank to the carburetor. It has a thin green light look that gives it a custom look, and as a Fuel Hose it is oil resistant so you can use it with confidence. View detail
I've never had a Tie Wrap of this type before.
[How is it used?
Used for several days.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When I replaced the Exhaust System, I had to fix the O2 SensorHarness to the Swing Arm because the layout of the O2 SensorHarness changed, and I found this Double Type Tie Wrap by chance while I was looking for a good way to fix it.
Because it was troublesome to measure the circumference length of Swing Arm of the deformed section, the length uses L397mm with the idea that Large also serves Small. Because the longer was easy to work when I think of workability, although the result was considerably too much, no problem.
The amount of movement of the Tie Wrap itself is large because it cannot be tightened strongly because it is tied together with Harness if it is Single Type, and Swing Arm is not suitable for use because it is a part that operates.
Unlike the Single Type, the Double Type can tie the Swing Arm and Harness separately, which is Merit.
The Swing Arm is tied tightly and fixed, and the Harness is loosely looped so that it can be used as a guide.
[Points to note]
You can choose between White and Black, but Black is used for outdoor use.
How did it compare to other products?
Webike has no competing products and is the only choice.
[Opinions and requests to Manufacturer
I don't need 5 bottles, so I would appreciate it if you could make the price for 3 bottles about 250 yen.
View detail