Reviews
Fits: HONDA ZOOMER(Ruckus), HONDA GORILLA, HONDA APE 50, HONDA APE 100, HONDA Live DIO Series, HONDA MONKEY, HONDA MONKEY, HONDA XR50 MOTARD, HONDA XR100MOTARD
Very easy and a little high Solo
Used for HA02-180 to square-grained CUB No. 90Custom.
I saw other people's impressions and gave it a try myself.
It is about 5mm shorter than OEM. This is unavoidable since the fitment is MONKEY and APE series and CUB Cas is not included.
The handlebar protrudes 2mm when mounted on the handlebar, but there is enough room for the grip length, so this is not a problem.
Silicon spray was applied to the protruding bar and grips where they might come in contact with each other. So far, no snagging.
Unlike OEM cones, this one is a Pierced Type, which is a good thing.
The product itself is recommended, but there is a possibility that the cone length may not be long enough for other than compatible car models. It is not recommended for safety reasons.
By the way, my CUB No. Grip is for Handlebar diameter Φ22.2, total length 120mm, inner length 118mm.
Quality is a bit cheesier than OEM.
The thickness is slightly thinner, and perhaps because of this, the grips can be inserted and removed without parts cleaner.
This is also not a problem, since Wire is fixed at the end anyway.
Throttle wire play was OK without adjustment, but it was difficult to ride when the operation was severe in town driving, so we increased the play a little, which was originally set to a small amount.
Now SHIFT UP is 15% faster. v
I'd like to see a medium to Large type for Vehicle made.
View detail
Fits: HONDA Super Cub 70, HONDA Super Cub 90, HONDA little cub, HONDA little cub
Don't let others make the same mistakes2
Used for square eye CUB90Custom HA02-180,.
I couldn't do it.
The size doesn't fit at all. The overall length is too short and the inside diameter is too small to fit at all.
The manufacturer's website says "Custom" is not available, even though CUB90 was listed as compatible. I made the same mistake as when I bought Grip before. Another waste of money.
There are so many types of CUBs that it's hard for a CUB novice to find the right one.
The product looked good Large change. It has a good rating and is inexpensive.
I would like to see the size indication.
View detail
Fits: YAMAHA SR400, YAMAHA SR500, YAMAHA SR400, YAMAHA SR500
For Grip heater installation
I bought this one because it is variously Large strange to divert OEMThrottle.
I am not sure about High Solo conversion.
View detail
Fits: HONDA Super Cub 70, HONDA Super Cub 90, HONDA little cub, HONDA little cub
OEM ratio up 10
It is a good product that is affordable and can be made into High Solo.
High Solo effect is further enhanced with Barrel Style Grip.
It is difficult to know at what stage to install the Grip thrust washer just by looking at the instruction manual.
Other manufacturers have products that can be made to High Solo, but they are too expensive for us to afford.
This is a Recommendation to PetitCustom.
View detail
Fits: YAMAHA SR400, YAMAHA SR500, YAMAHA SR400, YAMAHA SR500
For now, I'm happy with it
I was a little disappointed that there was some BALI left on the product It is easy to install However, I thought the change would not be as much if it wasn't a bit more High Solo-like View detail
Fits: YAMAHA Remote controller jog, YAMAHA Remote controller jog, YAMAHA Remote controller jog
It is not High Solo for JOG
I previously purchased this Manufacturer's Throttle for my CUB and DIO
Both of those items were slightly High Solo, so I'm going to take a slightly High Solo as well I bought it with high hopes
When I put it on, it had the same pull as NORMAL
When I checked, the product description said "High Solo" It was a misunderstanding based on our assumptions, as there was no mention of
You have listed the OEM Parts part number NORMAL same etc., not High Solo I would have appreciated it if you had clearly stated that
High Soloization was not achieved, but the product itself is very accurate and the OEM product is very good I think it's good enough for Repair
View detail
Fits: YAMAHA SR400, YAMAHA SR500, YAMAHA SR400, YAMAHA SR500
Good product
I bought two products because the original was broken. Good quality plastic and finish, acceptable price. This is a very good alternative to genuine one. View detail
Fits: YAMAHA SR400, YAMAHA SR500, YAMAHA SR400, YAMAHA SR500
This is for PenetratingGrip
Since the Accelerator Wire attachment part of the OEM cone worn out, it was exchanged for this.
The reason for choosing this product
1. Being Pierced Type
2. Being Flat face
Two points.
If SR replaces Handlebar with Other Company Product, hands are numb with vibration. In order to prevent it, we have installed Bar End Weight, but of course it will be a Penetrating end.
Until now I was cutting and using the end of the OEM cone, but since this product is Penetrating it can save time and effort to scrape and it is cleaner than I can.
Also, because the OEM is an octagon, corners will appear on the surface in the case of a thin Grip, but this is not bothersome with the Flat face. (Because it is a slippery, I think that it can be a bit slip-free Pattern fit)
Since the color is Black, the Grip end is also beautiful. (When it is an OEM, White appears from the end and Parenthesis is bad)
Adaptable GripLength is 120 mm and choices of Grip are many more good.
For High Solo, I uploaded photos so that I can compare hole positions with OEM. Throttle does not become heavy with High Solo which is slightly out of position of hole position and it is nice feeling.
Installation is Seat - Remove Tank, loosen AxelWire, then open Throttle holder and replace, then add Grip to restore all. Even if you lubricate Wire, you can replace it for 2 hours.
View detail