Reviews
Fits: HONDA CBX400F, HONDA CB400SF, HONDA CBR400F, HONDA CB400FOUR, HONDA CBX400F, HONDA CB400SF, HONDA CBR400F, HONDA CB400FOUR
Exhaust manifold Gasket
I chose the cheapest one and it was perfect - no problems and no gas leakage. View detail
Fits: HONDA CBR1000RR, HONDA CB1000 SUPER FOUR (Big One), HONDA CB1300 Super Four, HONDA CB1000 SUPER FOUR (Big One), HONDA CB1300 Super Four
When replacing the Exhaust System of CB1100etc!
[How is it used?
When we replaced the Exhaust System, we had to replace the Gasket as well, otherwise it would leak and cause power down.
How was your experience with it?
It is designed for CB1300, but can be installed on CB1100 without any problem.
Of course, the quality is fine and can be used without disposal leaks.
How did it compare to other products?
The cost performance is good because it is cheaper and of higher quality than OEM Product and KITACO's same etc. products.
[Points to note]
Note that if it has not been replaced for a long period of time, it will stick to the Engine side and scratch it if not carefully removed.
To prevent waste leakage, replace the exhaust system with a new one even if it is troublesome.
View detail
Fits: KAWASAKI GPZ750R, KAWASAKI GPZ900R, KAWASAKI ZRX1100, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZX-12R, KAWASAKI GPZ750R, KAWASAKI GPZ900R, KAWASAKI ZRX1100, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZZR1100/ZX-11, KAWASAKI ZX-12R
Posh Exhaust Gasket
I used it on my GPZ900R.
The price was low and it worked fine.
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
Beautiful nuts
I bought these nuts on the Honda SuperCub and Monkey - they fit both motorcycles. They are not expensive, but they protect the screw from harmful influences from below. The quality is good. I bought these nuts for a Honda SuperCub and Monkey - they fit both motorcycles. They are not expensive, but they protect the screw from harmful influences from below. The quality is good. View detail
Used for Exhaust System production
Used to make an exhaust system for a YamahaXV750E.
I used to use the ones NeoFACTORY handles, but when I bought the CFPosh ones to try out, I felt the quality of the bending process was better, so I decided to use CFPosh ones again this time.
As the description says, this Pipe has a high roundness rate regardless of the angle.
The Pipe itself is just a steel pipe, but the quality was good.
Also, although it was a cheap semi-automatic welder, it was able to weld without any problems.
I would like to have the opportunity to create another one next time and to purchase a Bend pipe with the Pipe diameter & bend angle I want.
View detail
For Exhaust System production!
It was used for the production of the original Exhaust System.
It is a 750cc 2-cylinder, but it is not such a sporty Engine, so we decided to make it with 38mm just below the Flange.
In the case of VTWINEngine like I am doing, I could easily make a front bank by buying a Pipe with a 180 degree bend and a 60 degree bend, and cutting and stretching it well.
The one I purchased this time is for Rear bank.
Rear banks have to be twisted into tight spaces, so they end up having to be chopped up.
The Pipe itself is frankly just a 1.6mm-thick steel pipe, but it is bent almost as a new circle.
Last time I bought BentPipe, which is handled by NeoFACTORY, I felt that CFPosh was better in terms of new circularity at the beginning of bending.
By the way, the product image looks about 100 degrees, but please be assured that what you will receive is a proper 90-degrees bend.
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
Long Exhaust Nut
I purchased silencer attachment pins to the cylinder on my Honda monkey for corrosion protection. In terms of quality, everything is fine, they are well loaded, the appearance is gorgeous. I recommend to purchase ... View detail
Wrapping around exhaust pipe
There was a concern about heat when converting to Atech-SPL, so it was installed in the OEM exhaust pipe.
Result 3. Quantity:I used it for 5pcs. It was easy to roll with good color and little fluff.
It is fully baked but still has a sweet aroma.
View detail
For Heat Protection and Fashion
I don't want to touch the exhaust pipe that just ran and get sizzling.
I thought of various reasons why it would be dangerous for children to touch it.
I love the Parenthesis with the cloth wrapped around the Motorcycle!" was wound up with the real story!
While it gives a sense of custom at once, it also gives a sense of raggedness.
I think it looks unbearably tacky to some people.
I think it's cool! I think it's cool, so I'll pass.
When rolled up, the insulation performance is good, and it appears to provide a slight sound insulation.
I'm personally pleased with Large!
Yes, I also diverted this one to repacking sound deadening material inside the Exhaust System.
Ordinary Glass Wool would fly away, so I thought this would be a good choice.
The result was a Large success.
View detail
DF200 DJEBEL Used at Rough & Road RSVSilencer
I purchased a used RSVSilencer and installed it because it was too annoying.
BoltQuantity for installation:They said 2 pcs, but we decided to TRY with 1 pc.
The rear end of the Silencer is gradually enlarged from 3, 4.5, to 6.5mm to allow the attached M6 bolt to penetrate.
"Okay" and put it against the Silencer exit... I can't get in!"
Caliper's actual measurement was 47mm, so I bought 47mm, but 46mm seemed to be the right choice.
I inserted it by tapping it as hard as I could with the wooden handle of the plastic handles.
After the installation, the exhaust sound was very loud. Slightly more energetic NORMAL?" Ranked first.
When Idling "Chica Chica." and the Tappet sound is so good that it sounds like a HUDDRILL. This is good.
I immediately performed a test run and did not feel any extreme power down, even when I turned it as hard as I could.
Also, totally unexpectedly, the low-speed Torque was enriched.
I am satisfied with the Large change because it is quieter and easier to ride.
I found this in someone else's Review, but the Hexagonal Wrench was not attached.
View detail
Fits: HONDA ZOOMER(Ruckus), HONDA ZOOMER(Ruckus), HONDA TODAY, HONDA TODAY, HONDA SMART DIO, HONDA SMART DIO
When replacing the Exhaust System
[How is it used? Used for ZOOMER
Was the one you received as per Image? Yes
How was your experience with it? no problem
[Points to note] There is none
How did it compare to other products? I think it's a good product.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
Fits: KAWASAKI EX-4, KAWASAKI W400, KAWASAKI W650, KAWASAKI W800, KAWASAKI EX-4, KAWASAKI W400, KAWASAKI W650, KAWASAKI W800
no problem
I used it on a W650 assembly pipe and it installed without any problems. View detail
Aluminum is dirtier and less rusty
Material:I chose this one because it is aluminum and seems to be rustproof.
It is not cheap, and the precision is perfect.
View detail
It'll be quieter than you think.
I installed it on my KSR110 Nassat RR with an external exhaust system, and even though it is a JMCA Certified exhaust system, I bought it to avoid disturbing my neighbors because of the heavy bass sound. It is quieter than I expected. I don't think I'll have any complaints about this. View detail
Used for SUNDANCE HYPEROrange
Used for SundanceHYPEROrangeExhaust System for XL883.
I installed this product to reduce the volume at the time of vehicle inspection. (Required processing)
The car passed inspection with no problems.
View detail
Fits: HONDA livudio, HONDA livudio, HONDA diocesan, HONDA Livudio SR, HONDA Livdio ZX, HONDA livudio, HONDA diocesan, HONDA Livudio SR, HONDA Livdio ZX
For Refresh
I bought it because I replaced the exhaust system for the refresh of LIVE DIOZx.
This is a necessity for Exhaust System replacement.
It's a few hundred dollars, so use it, don't use it, and make it new.
Since the mounting part is pointing downward, I lightly used all-purpose grease to scratch it and then put in the exhaust system.
View detail
Fits: HONDA ZOOMER(Ruckus), HONDA ZOOMER(Ruckus), HONDA TODAY, HONDA TODAY, HONDA SMART DIO, HONDA SMART DIO
It was carefully crafted.
After purchasing it, I lost it temporarily and had no choice but to purchase another Manufacturer's and a liquid Gasket at the Shop, but found it soon after.
Thanks to this, I recognized the quality of the Posh ones when I saw that both sides of the Gasket were pre-coated with liquid Gasket.
View detail
Best way to keep the volume down!
Our new addition to the family, the NINJA Exhaust System, was a blast.
For me, living in a housing complex, it's a Large problem.
So I bought this product to quickly turn down the volume.
If you put it on, it has a significant sound deadening effect.
However, the exhaust air pressure may be too high, or it may be too high at mid-acceleration.
When I open the Large Available Axel, the Engine won't turn with a buzzing sound.
In a straight tube, it blows up good...
It was a choice between volume or performance, and which was the priority.
The answer I came up with was to buy a new Silencer! next to (esp. to)
This product has been discontinued.
The product itself has high machining accuracy, 2-point stop, HexaWrench included, and is a good example of a good quality product.
I think it's a high cost product.
View detail
Fits: KAWASAKI GPZ400, KAWASAKI GPz400F/F2, KAWASAKI GPZ400R, KAWASAKI Z400FX/Z400J, KAWASAKI Z400GP, KAWASAKI Zephyr 400, KAWASAKI Zephyr X, KAWASAKI Zephyr 750, KAWASAKI GPZ400, KAWASAKI GPz400F/F2, KAWASAKI GPZ400R, KAWASAKI Z400FX/Z400J, KAWASAKI Z400GP, KAWASAKI Zephyr 400, KAWASAKI Zephyr X, KAWASAKI Zephyr 750
Good!
I used it to replace the external exhaust system!
Installation was no problem
It will be a necessity for an oil change and I'll be buying it again!
View detail
Essential for Full Exhaust System
I had previously purchased a CB250R'19 exhaust system from OEM. I had the opportunity to change to Yamamoto racing's Full Exhaust System Used.
I am using it to great effect.
I've been able to use it for about 6 months with no problems with the exhaust etc. and the product is perfectly fine.
It seems to be able to use it because it is the same engine though it is with CBR250R in adaptation.
No CB250R compatible Gasket available? It is possible to use this product without any problem. It's also available in the Exhaust System, so please use it!
View detail