Reviews
Secondary Air Cancellation
This is a Kit to do secondary air Cancellation.
It is easier to work with if the Radiator is shifted.
Be careful to check the orientation and Gasket of the Valve you removed.
When you take it off and put it back on, what?
I thought I was in the clear, but I had the Manual.
I was able to install it.
It seems that removing Wiring causes an error, so I removed Hose.
Coupler remains connected.
The only weight reduction is the Hose part. I hope the exhaust efficiency will be improved!
Race vehicles and cannot be driven on public roads.
View detail
Fits: YAMAHA WR250 R, YAMAHA WR250 R Reverse, YAMAHA WR250 X, YAMAHA WR250 X Reverse, YAMAHA WR250 R, YAMAHA WR250 R Reverse, YAMAHA WR250 X, YAMAHA WR250 X Reverse
Sub computer
The stalls stopped even with a one-piece installation. View detail
I liked Black.
I don't know the feeling of use frankly because I put it on the used car which I bought suddenly.
It's good because you can hardly see it, but my personal preference would have been Black.
The Instruction Manual says to put the removed Lead Valve back in place, but if you want to assemble it with the Bulb Not Included, you need to buy the Bolt separately or it will be too long.
The warning light comes on, so I leave the AXIS cheater and connect the Connector to it, but I wish it came with something like the CanSeraR so I could remove it.
View detail
It's not something you can really feel, but...
This part shuts off the introduction of secondary air.
The installation itself is easy, but it is quite Large strange to that point.
I have to remove the tank, air cleaner box and flip the rubber cover for heat shield.
The back side is threaded through the throttle body, so you can flip it from the front side.
In order to do so, the Ignition and Sensor connectors connected to the cylinder head must be disconnected.
If you remove the fixed Bolt of Radiator and set it to Free, you can flip the Cover.
Rubber cover has to be cured Throttle etc. because of the sand and dust on it.
The product itself is Cut-out of Aluminum, and the texture is high.
After all, it is expensive for the parts and a bit heavy compared to OEM.
It's a shame because weight reduction is a very simple task and I would like to gain more value with external parts like this. (Although it is lighter in terms of the whole system)
As for the effect, in the case of Racing Exhaust System of AKRAPOVIC
The bobbing that happens just before I fully revert the Axel has improved.
It's not completely fixed. It seems to have an effect on After Fire of a common popping sound, but it doesn't know because it doesn't have it originally. Probably, it will be effective for that one.
As for the OEM, there is no change at all.
I've heard that it weakens the embrasure, but no there either.
(I'm not sure about Mechanism on this one)
View detail
The actual AIS block-off plate is good. Not sure about the airbox cap though.
The K&T AIS block-off plate for the exhaust side works perfectly. That said, I cannot stress how happy I am with this purchase. As for the airbox cap, it's the complete opposite. It just wont fit my bike so I ordered my own set of silicon vacuum caps. Build quality of both items along with the hex screws are great though - no doubt about that. There's no need for manuals too since it's a plug and play device. View detail
Good for a bit of commitment
Other AISCancellationItems are also sold at cheaper ones. The lid on the engine side of K & T was made fancy so select this. I wrote to cover the Hose in the Instruction Manual, but I wanted to lid directly on the Air cleaner Box side, so I closed it with the Pipe end cap 13 mm of Home center. Would you like to make the lid on the engine sticky? I think that you want to consider purchasing depending on whether you want to make it a simple Plate. View detail
To secondary air Cancellation!
WR250R 2015MODEL
I bought it for secondary air Cancellation.
Installation was easier than I thought.
However, as I forgot to prepare the Engine side Gasket, I used it only there but it was not a problem.
It is even better to have such fine parts included.
It was supposed to cover the last Pipe of Valve if it was an instruction manual, but since Pipe to Air cleaner is long, it is unbelievable, so Cut it in the immediate place and closed the lid.
We also removed the secondary air valve body and made EngineLeft Side clearer. Wiring also handled Waterproof and so far there is no problem.
View detail
The After Fire was uncanny when WR250R carried out Muffler exchange.After that was as uncanny as it thought whether the Muffler broke attached and carried out the clean cut, the After Fire was completely lost.OK and anyone can do attachment.AI system
The After Fire was uncanny when WR250R carried out Muffler exchange.After that was as uncanny as it thought whether the Muffler broke attached and carried out the clean cut, the After Fire was completely lost.OK and anyone can do
attachment.AI system picking outside carried out after clean cut attachment.The Blind of the Air cleaner box left the Hose of Ai System by the side of a VOX, and used the Blind lid which was attached to the Hose at the clean cut.After removing
Ai System, since Engine left-hand side felt it refreshed, the phon was attached backward, and also it was felt refreshed.
View detail
It attached together on the occasion of Muffler exchange. attachment is dramatically easy. It is a Recommendation at the beginners. However, since A.I. Artificial Intelligence equipment remained as it is, it was set to three.
It attached together on the occasion of Muffler exchange.
attachment is dramatically easy.
It is a Recommendation at the
beginners.
However, since A.I. Artificial Intelligence equipment remained as it is, it was set to three.
View detail
being NC shaving and coming out, although there are a direction made on one's own and goods same from several companies -- merit [ processing accuracy ] -- since that was right, it purchased. Actual goods are also made carefully processing of the accuracy
being NC shaving and coming out, although there are a direction made on one's own and goods same from several companies -- merit [ processing accuracy ] -- since that was right, it purchased. Actual goods are also made carefully processing of the accuracy of a clamp face, and a Bolt hole, etc. Although a little high mind was also carried out, since time and effort was taken, it was thought that it was an appropriate amount of money. View detail