Reviews
Maintenance of Chain, which I am not good at, could be easier.
I've only done simple cleaning when I sprayed oil in the past, so I think I can do it a little better from now on. View detail
Spring Detachable
I purchased this product to use for removing and installing springs when removing and maintaining the Exhaust System.
The length is just right, no slippage or pain at the grips, and they are easy to use.
I don't use it that often, but it would be useful to have 1 pc.
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA
AF24Giorno
Used for AF24Giorno.
Coil was easily removed.
View detail
For Scooter.
I purchased this product to replace the drivetrain on my Scooter.
However, I used it first for bore up work on a friend's SUPER CUB.
It works without any problems.
View detail
no problem
[How is it used?
To remove the center nut of the clutch
Was the one you received as per Image?
Yes
How was your experience with it?
It can be used with no problem, but you have to apply it firmly and straight.
Easily slanted
[Points to note]
Centrifugal for Clutch Band holder required
It said not to use Impact.
I used Impact when loosening lol.
It is only used when ClutchRose is used, so it is not likely to be used anymore.
View detail
cheap
OEMClutch holders are expensive, so we purchased this one.
Unlike OEM, it is not fitted into a hole, so although it is unstable, it can be substituted adequately.
View detail
Reasonable
OEM clutch holders are expensive, so we used this one instead.
This is sufficient for use.
View detail
I chose it for the cospa.
I bought this in a hurry because the Piston Pin was very dirty.
I chose it for its price, but after using it, I am satisfied with its workability and functionality.
View detail
MinimotoBrake Piston Pliers
Purchased because I am replacing the pad with Self. It is inexpensive and easy to use. View detail
It is easy to use
This was the first time I rode Brake's Piston, and I was pleased with how easy it was to use. However, since I have an air compressor, I don't think I needed it. View detail
To disassemble the Clutch
[How is it used?
TZr250R (3XV) I bought this to Rose the Clutch of
Universal's Clutch holder is available from several manufacturers, but I chose this product which was relatively inexpensive.
Was the one you received as per Image?
It's no surprise since it keeps the Clutch down, but it was much bigger than I imagined.
There was no deformation, and the production seemed to be good.
How was your experience with it?
I used it for the first time so I had to watch and learn, but it was surprisingly easy to fix.
I was worried because there was an imprecation that it could not be fixed, but I did not have any problem.
However, I was a little worried because the hook was shallow, probably because of Universal.
[Points to note]
It is important to note that depending on the motorcycle, there is a possibility that the hook may be shallow or not hooked.
【Review】
The tool is only used to hold down the Clutch, but it made the job easier.
It's not that expensive, so it's handy to have one if you're rooting an engine.
View detail
What? You don't have it yet?
Chain polish, it's fun, isn't it?
Thanks to the Chain lube, the dirt sticks to the surface quite well and is worth removing.
If you use a normal brush, you will have a hard time because there are many places to polish, but with this, you can wash the whole surface in no time if you stop thinking and just jerk and jerk. It's impossible to clean the Chain without this.
Let's buy this one together.
https://www.webike.net/sd/67726/
If the stain is hard to remove, spray it with Degreaser and let it sit for a bit, then rinse it off with hot water while jerking it around with this brush, and it usually comes off beautifully.
View detail
Lock Function is very useful!
The night of 15 when I thought that all Piston Extractors were the same.
Piston polish that was convenient to use the lock mechanism this time
BlueMagic is seriously awesome!
Well, what I'm trying to say is, congratulations on your marriage, Gacky!
View detail
Wound goes into Piston.
Used for Caliper piston rub.
It is impossible to pull out the piston without this, unless the piston is in a good mood right after assembly.
There was no hesitation in using it, and it was strong enough to be used for a 250cc single push Single.
The drawback is that the lock to keep the tool open is applied by itself when you notice it, and Stress may boil. It's not a fatal problem, but the Lock Function is not really needed.
In addition, because the edge of the tool bites into the inside of the piston structurally, the piston will be scratched to a small extent. This is unavoidable, but if you are a nervous worker, you must take measures such as biting the Dustcloth.
View detail
Takes some getting used to?
I tried to replace Seal because I removed the Caliper, but it was on the way. "Oh, that's easy! . But I couldn't pull out the whole thing because I couldn't spread it out and lift it up. View detail
Fits: KTM Hydraulic ClutchSpec. car
Pretty handy.
Time-consuming air removal is very efficient and convenient with this. It was easier to handle inhalation than injection. Work time is definitely reduced. View detail
Fits: HONDA CROSS CUB, HONDA SUPER CUB110, HONDA glom, HONDA SUPER CUB 50
If it's the right size.
Used to remove the Outer Rotor on a BANDIT250gj74
Size and Pitch will fit, but it will come off if you prepare a longer one or if you devise a little method because the length of the bolt is short.
It was pretty hard, but I was able to get it off without breaking.
View detail
It's not something you'll use more than once, which is enough.
I was trying to replace the Generator that was no longer generating power, and at the same time, I was trying to replace the StarterClutch that was showing signs of slippage poof.
I bought it because I needed to detach the Magnet rotor.
The price of the Kawasaki OEM SST is too high, so I made an Adapter for this Fly Wheel Puller to fit the Pitch.
It is important to use the air impact to turn the car all at once and to degrease the crank end thoroughly when assembling it.
The texture of the tool was not particularly cheap, and the normal hardened tool steel was used with no problems.
However, considering the fastening torque, I don't think you should think of it as a tool that will last forever once you buy it.
I wonder if I should buy a new one after 3-4 uses.
View detail
I think the grip could be a little thicker
I bought it to try Caliper cleaning and used it immediately after receiving the product
There are many similar products, and if you look at the reviews, you'll often see that the inside of the Piston is damaged It's often reviewed, but so is this one
I used Vinyl Tape wrapped around it as appropriate
It is not so hard to turn the Piston, but it is still a little hard, so the Grip can be thin It was there and it was easy to get tired
It's a cheap part of the market if you think about it including points, so it's just right for those who are interested in it
View detail
Fits: HONDA GORILLA, HONDA MONKEY, HONDA MONKEY BAJA, HONDA MONKEY R, HONDA MONKEY RT
Clutch disassembly essentials
These tools are essential for replacing the Clutch on the HondaHorizontal TypeEngine
I have seen some people making their own sockets by cutting off the sockets, but when you consider the price and quality, you need to buy a special tool to make it I think you should
The Material seems to rust easily, but..
View detail