Reviews
Is ServiStool easier to use?
Purchased due to lack of OEM Product adjustment Wrench.
The YZF-R3 adjustment Wrench I used to use is sufficient for my needs.
I tried Universal Product as a test.
Half of the Wrench is movable, so you have to hold the tip of the Wrench by hand each time.
It is a Universal Product, so there is no choice.
Other than that, I have no complaints.
View detail
Cheap, but not easy to use.
[How is it used?
Used for Engine O/H of TZr50R.
In particular, a universal holder like this product is needed to remove the fixed nut of the Clutch.
Was the one you received as per Image?
We selected this product because it had the lowest Gold amount.
To be honest, I thought the cheap price would make the product quite poor, but it was not as bad as I expected.
The supplier may be the same as the ones offered by other Manufacturers because the pictures are the same.
How was your experience with it?
The ease of use is not all that great.
In the case of TZr, the fixed pin is hooked to the clutch housing, but the fixed pin is short and easily comes off,
I cannot apply force well. I have the impression that the size is not right for 4EUEngine, although it may be just the right size for other Scooters.
[Points to note]
Be careful not to put the fixed Pin in the wrong place.
I used it on two engines and accidentally put a pin on the bolt hole of the clutch, destroying the bolt hole.
How did it compare to other products?
Similar products are lined up at similar Gold prices, as if the suppliers are the same.
Once you buy one, it will last a lifetime, so you might as well get something a little more decent.
View detail
MINIMOTO Minimoto Tappet Adjustment Tool 3-Size Set
Fine-tuning of Valve clearance is more convenient than using ordinary tools
The accuracy of the tools is low and I would like to see the system a little more precise.
View detail
Can't hold the nail open.
[How is it used?
I used this to replace the Clutch boss on my MT-07.
Was the one you received as per Image?
This is a general Clutch holder. There are several companies that sell the same shape.
How was your experience with it?
The pawl tip format is bad, and when Torque is applied, the Y-shape spreads and the pawl comes off. There is a screw type stopper to control the spread, but it is defeated by Torque.
The reason it spreads is that the tip of the nail is cut at an angle to fit easily into the groove of the Clutch boss.
I had to tighten the Stopper with a water pump ply shop to get it to work. I don't think that's the way it should be used.
[Points to note]
The Clutch boss has a high fastening torque, so if it comes off you could get hurt.
View detail
The strength of the product is reliable.
The price may be a little cheaper, but for the appearance, it is strong and durable. You can pull the hard spring and prevent the exhaust system from being scratched and you can use it safely. View detail
Can be used without problems
Function and workability are fine, but
The part that suppresses Piston is Knurl by the genus Gold, so it scratches the inside of Piston.
If you are worried about it, you need to take measures such as putting Dustcloth in between.
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA
At least it works for now
I used it on a vehicle that was purchased new and is now a year old
There was no rust or anything like that
I struggled a lot
Either the tool will break or the Flywheel will come off
It was a close call
I managed to get it off
View detail
Can be used for low torque parts, product accuracy is decent
Used to install the StemLock nut on the LITTLE CUB
After replacing the Stem bearing, it was useful for initial tightening during installation
Because of its construction, it cannot withstand high torques and is limited in its use
The downside is that the pivot is too loose and makes the task a bit cumbersome
If you think of it as an auxiliary tool, it's a passable grade
View detail
MINIMOTOMinimoto Clutch Holder Fook-Type
MINIMOTOMinimoto Clutch Holder Fook-Type Commercial Product No : It is 1900. We purchased TZr 250 for Clutch disassembly. OEM purchased because there was no stock. Especially served without problems. View detail
I bought it for Maintenance around Steering.
Since there are two Motorcycle, Size It is possible to use it steplessly. With the thickness of the moving part, the tool does not enter with the Top Bridge attached. After tightening with this, tightening Nut of Top Bridge was too hard and could not be adjusted easily. Once it was tightened, loosened, tightened, it became in a condition that it was convinced by delicately adjusting it the first time after tightening the Top Bridge.
The tool itself is solid and easy to use.
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA
Watch Impre
I watched Impre, I bought it for reference and saw it.
Very easy to use, I'm very happy.
For those who are considering purchasing, I'd recommend that.
I think that it will not break easily.
View detail
Good for using for the time being ....
Although Cost is cheap, it is attractive that it is cheap, but because Firefox moves, it does not engage well and it is not easy to use. It is convenient to use for a while because I wanted to use the adjustment of Rear suspension of XL 1200 C SPORTSTER 1200, but if you know the Size to use, it would be better if you purchased that Size's.
However, because it is not a frequently used tool, I think that this Cost is a good product if it can be used widely. In my case, I do not even know Size and I did not like it if I could not use it after purchasing, so I bought such a worried one.
View detail
I bought it at a price
I thought about buying it by looking at the opportunity from before
Previously I was listing products from other Manufacturer
I found this item this time and purchased it because the price was cheaper than the previous one
Because I have not used it yet - - -
View detail
It is a nail type Universal holder. Since an Impact also carries out Torque management with the last Torque wrench at attachment when removing, the surroundings stop of a Clutch center requires this Type of Holder. If a 1-time limitation
It is a nail type Universal holder.
Since an Impact also carries out Torque management with the last Torque wrench at attachment when removing, the surroundings stop of a Clutch center requires this Type of Holder.
If a 1-time limitation or -- is thought since it is too cheap, anticipation is betrayed and it can use perfectly.When carrying out a Friction-plate addition by Clutch strengthening of Scorpa, it used, but there are likely to be other uses.
View detail