Reviews
Cheap, but not easy to use.
[How is it used?
Used for Engine O/H of TZr50R.
In particular, a universal holder like this product is needed to remove the fixed nut of the Clutch.
Was the one you received as per Image?
We selected this product because it had the lowest Gold amount.
To be honest, I thought the cheap price would make the product quite poor, but it was not as bad as I expected.
The supplier may be the same as the ones offered by other Manufacturers because the pictures are the same.
How was your experience with it?
The ease of use is not all that great.
In the case of TZr, the fixed pin is hooked to the clutch housing, but the fixed pin is short and easily comes off,
I cannot apply force well. I have the impression that the size is not right for 4EUEngine, although it may be just the right size for other Scooters.
[Points to note]
Be careful not to put the fixed Pin in the wrong place.
I used it on two engines and accidentally put a pin on the bolt hole of the clutch, destroying the bolt hole.
How did it compare to other products?
Similar products are lined up at similar Gold prices, as if the suppliers are the same.
Once you buy one, it will last a lifetime, so you might as well get something a little more decent.
View detail
Universal but...
I was looking for a Universal Oil filter wrench and found this one.
Compared to other companies' products, we chose this one because it can accommodate a large diameter.
In fact, I used it for Oil replacement and found it very nice that the Socket is compatible with 9.5 and 12.7.
However, the part that grips the Filter is still bare steel, so it will scratch the Filter when tightened.
The Oil Filter is basically out of sight, which was a little disappointing.
View detail
That's about it
I used it for the first time and was able to adjust it. It would have been easier if the tip was cut thinner to make it easier to get into the gap. View detail
Grom JC92 can't be used as it is, but I was able to get the Piston Pin out with ease.
Piston Pin Puller, very useful.
I bought it because it was listed as having a compatible Piston Pin Size of 12mm to 25mm, but I need to take a moment to pull out the 12mm Piston Pin of the Grom JC92.
The construction of the product is very good, the grips are anodized, and it is not cheap.
Four types of attachments are included for pulling out the Piston Pin, which may be used on Large Motorcycle.
In the case of the Grom JC92 Piston, the smallest attachment has an outside diameter of more than 12mm, so the attachment is caught on the Piston perimeter and does not reach the Piston Pin.
So I pulled it out by biting a Spacer with an outside diameter of less than 12mm and about 5 cm, as shown in the photo.
The Curve on the Piston contact side of the Grip section was also fit to the Piston.
The Piston ring acted as a good buffer to prevent damage to the Piston, so there was no need to protect it with Dustclothetc.
View detail
MINIMOTO Minimoto Tappet Adjustment Tool 3-Size Set
Fine-tuning of Valve clearance is more convenient than using ordinary tools
The accuracy of the tools is low and I would like to see the system a little more precise.
View detail
For cleaning the fins of air-cooled engines!
[How is it used?
I use it for the engine wash for Vehicle of XJR1300C of MainMotorcycle which is an air-cooled engine.
Surprisingly, I've been looking for a longer, stiffer Brush like this and it's been very helpful for Engine washes.
Was the one you received as per Image?
I thought the hair was a little shorter than the Image. There was no Scale, so you can use the Keyboard as a guide.
The tips of the bristles are quite stiff and scrape out the dirt well.
How was your experience with it?
It's got a wooden handle, very easy to use! I would recommend this to anyone with another air cooled engine!
If you use it too roughly, the brush can get rough, bent, and loose, so I think it's more than worth the price, but I'd be happy if it was more durable!
[Points to note]
The bristles are hard, so if you wash too hard, you may damage the paint on the Engine, so it's better to be gentle when using it.
It is also not recommended for scratches on the body, etc. It is recommended for stubborn stains on the wheels and undercarriage, off cars, etc.
How did it compare to other products?
The bristles are longer than the other brushes, so you can scrape out the dirt and grime. This brush is recommended for those who want to scrape out fine dirt from deep inside.
I also bought a Brush from Motorun, but it was still not long enough for my Engine fin.... It is just the right length and is very useful.
Also, the fact that the bristles are made of durable PVCNylon and are not affected by solvents is a GoodPoint!
View detail
Can't hold the nail open.
[How is it used?
I used this to replace the Clutch boss on my MT-07.
Was the one you received as per Image?
This is a general Clutch holder. There are several companies that sell the same shape.
How was your experience with it?
The pawl tip format is bad, and when Torque is applied, the Y-shape spreads and the pawl comes off. There is a screw type stopper to control the spread, but it is defeated by Torque.
The reason it spreads is that the tip of the nail is cut at an angle to fit easily into the groove of the Clutch boss.
I had to tighten the Stopper with a water pump ply shop to get it to work. I don't think that's the way it should be used.
[Points to note]
The Clutch boss has a high fastening torque, so if it comes off you could get hurt.
View detail
The strength of the product is reliable.
The price may be a little cheaper, but for the appearance, it is strong and durable. You can pull the hard spring and prevent the exhaust system from being scratched and you can use it safely. View detail
Can be used without problems
Function and workability are fine, but
The part that suppresses Piston is Knurl by the genus Gold, so it scratches the inside of Piston.
If you are worried about it, you need to take measures such as putting Dustcloth in between.
View detail
It's not a problem
MINIMOTOMinimotoThe MinimotoPiston ring compressor has arrived, so I'm going to give it to you I'd like to give you a quick in-play of how it feels to use it
I think the quality of the product is reasonable for the price range
It's safe to say that you won't be disappointed by the amount of gold you buy, which is Large
I bought the product and I don't feel like I'm losing money
As far as shopping goes, I felt like it wasn't a loss
It is a product worth the Gold amount
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA
At least it works for now
I used it on a vehicle that was purchased new and is now a year old
There was no rust or anything like that
I struggled a lot
Either the tool will break or the Flywheel will come off
It was a close call
I managed to get it off
View detail
Can be used for low torque parts, product accuracy is decent
Used to install the StemLock nut on the LITTLE CUB
After replacing the Stem bearing, it was useful for initial tightening during installation
Because of its construction, it cannot withstand high torques and is limited in its use
The downside is that the pivot is too loose and makes the task a bit cumbersome
If you think of it as an auxiliary tool, it's a passable grade
View detail
So so
Harley is pretty heavy on the car body so Jack-up, I am concerned about stability, so I will not up too high, but I can use it normally. View detail
Easy to exchange with Tray
Because the capacity is 2 L, Oil quantity such as ~ 125 cc is for 1 L small Engine Displacement Volume for cars.
The mouth for waste oil folds back Small and flat, so it is easy to spill when throwing away as they are squeezed in order.
View detail
slide
It is quite slippery and clip slips and it is hard to remove.
Just thinking about the price makes Cost performance satisfactory.
You can use it enough if you devise how to use it.
View detail
MINIMOTOMinimoto Clutch Holder Fook-Type
MINIMOTOMinimoto Clutch Holder Fook-Type Commercial Product No : It is 1900. We purchased TZr 250 for Clutch disassembly. OEM purchased because there was no stock. Especially served without problems. View detail
I bought it for Maintenance around Steering.
Since there are two Motorcycle, Size It is possible to use it steplessly. With the thickness of the moving part, the tool does not enter with the Top Bridge attached. After tightening with this, tightening Nut of Top Bridge was too hard and could not be adjusted easily. Once it was tightened, loosened, tightened, it became in a condition that it was convinced by delicately adjusting it the first time after tightening the Top Bridge.
The tool itself is solid and easy to use.
View detail
In cospa
Oil It was used during replacement. Oil Since it is about one exchange every 3 times it is not expensive, but it was cheap so I bought it all together. I'm satisfied because I can save the trouble of using the water-resistance paper to familiarize the surface and use it again. View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA
Watch Impre
I watched Impre, I bought it for reference and saw it.
Very easy to use, I'm very happy.
For those who are considering purchasing, I'd recommend that.
I think that it will not break easily.
View detail
Good for using for the time being ....
Although Cost is cheap, it is attractive that it is cheap, but because Firefox moves, it does not engage well and it is not easy to use. It is convenient to use for a while because I wanted to use the adjustment of Rear suspension of XL 1200 C SPORTSTER 1200, but if you know the Size to use, it would be better if you purchased that Size's.
However, because it is not a frequently used tool, I think that this Cost is a good product if it can be used widely. In my case, I do not even know Size and I did not like it if I could not use it after purchasing, so I bought such a worried one.
View detail