Reviews
Fits: HONDA GROM, HONDA MONKEY125, HONDA MONKEY, HONDA DAX, HONDA MSX, HONDA XRMOTARD, HONDA CHALY, HONDA APE, HONDA CT125CT110 HUNTER CUB
MONKEY125 beware.
Purchased for maintenance of MONKEY125, such as oil replacement.
Be careful when lowering.
If you lower it too vigorously, your hand may get caught between the Arm of STAND and the License Plate.
Hands get caught, License Plate gets bent….
but with great strength and stability.
View detail
Retro feel is good.
The material of the Key Holder is soft and will not damage the keyhole.
The design is also good with a retro feel.
View detail
Fits: HONDA MONKEY, HONDA GROM, HONDA MSX, HONDA APE, HONDA MONKEY125, HONDA DAX, HONDA CHALY, HONDA XRMOTARD, HONDA CT125CT110 HUNTER CUB
Lightweight and just right for groms.
It is tiny and ExactlySize for groms.
I just put Swing Arm on it, but it is stable.
(Caution!)
Normal rear fender will cut your finger on the License Plate if you are not a little careful.
I will try Fender Eliminator one of these days.
View detail
Cheaper than other companies' products.
It was easy to install, and most importantly, it is inexpensive. View detail
Fits: HONDA SUPER CUB110, HONDA CROSS CUB50, HONDA CROSSCUB110, HONDA SUPER CUB 50
Good value and easy to try
This product looks just like a certain Manufacturer's. I haven't compared them, so it's just my opinion. I didn't compare them, so it's just my opinion, but this one is half the price and probably the texture is the same. So, it is a good value.
The installation was a little off in dimension, but if you pull it by force, the installation went easily.
With NORMAL Suspension, there is a gap, but if you are changing to an external one, the gap may be very narrow.
I forcibly pulled it outward by force after installation to create a gap.
It is a little smaller than the Side bag, which is the Minus1Point of use. Other than that, I am generally satisfied.
View detail
Fits: HONDA GROM, HONDA MONKEY125, HONDA MONKEY, HONDA DAX, HONDA MSX, HONDA XRMOTARD, HONDA CHALY, HONDA APE, HONDA CT125CT110 HUNTER CUB
Perfect for the MONKEY125!
It is essential for maintenance. I'm glad it's cheap. Durability is unknown. View detail
Cost performance good!
I was looking for a Ladder to load my kid's QR on the Land Cruiser 60.
We decided that it was too tough to lift up on a car that was lifting up, so we bought this one.
First of all, Cost performance is the best.
The construction is not bad.
I'm so glad I bought it so I wouldn't hurt my back!
View detail
Fits: HONDA SUPER CUB110, HONDA CROSS CUB50, HONDA CROSSCUB110, HONDA SUPER CUB 50
I wonder if there's a reason it's cheap.
The product is excellent, I installed it on my CROSS CUBJA45, but the included screw didn't fit the CarrierBody hole (Screw diameter is too thin and rattling), so I bought the Spacer 30mm Spacer for M6 at home center (4 pieces for about 100 yen). If you can remove the rear carrier, it will be easier to install. Removing the existing screw (using Hexagonal Wrench #5) from the body of the car may have some individual differences, but it's hard to remove the existing screw (using Hexagonal Wrench #5) from the body of the car with a very hard and short Hexagonal Wrench. If you combine the Hexagonal wrench with the eyeglass wrench, it will come off unexpectedly easily. To fit the screw hole of the car body, you need to construct while raising the rear cowl, but if you can grasp the hang, you can install Firmly. The appearance is also Parenthesis good, and I do not know the information of the method of installation and bracket made by KI●●MA, but if it is similar, I think that this is a buy because there is a price difference. The installation time was about 20 minutes after removing Rear Carrier. View detail
Used for MONKEY, DAX, CHALY, etc.
The vehicle is so light that I don't think it would be a problem without the Roller.
I didn't care for the color so I went with Red, which is in stock.
I'll have to wait and see how the moving parts of the receiver hold up.
In the meantime, I don't regret my purchase.
View detail
Assuming you make changes
I bought it with the intention of using it to replace the XR100MOTARD's Shock
Because it's an imported product, I thought Wound was inevitable, and the Touch up paint for rust prevention was prepared So it was Large sturdy But, however, the hole through which the Front wheelStopper Pin is threaded seems to be a spatter of welding Accident occurred on BALI that the paint got on and the pin wouldn't go through I stripped it off with Graver and touched up paint immediately
It's an international product, so I guess it's worth the price I thought it was a good idea I'd hope for a warranty replacement if it's a solid product with a high price and quality, but I'd rework it at my own risk If you are a scheduled User, I recommend it
Since it is the WheelStopper with the widest Inch adaptation
The vehicle is nice and calm I've been wanting one of these products for a while now
It's like a lie that I was struggling with wheel stops, chain blocks, and MotorcycleJack It is
View detail
A little more quality control;
First things first
The construction is solid and normal
Cosmetically, rave reviews
Just paint & hellip;
There were places where it looked like the paint had been partially over-sprayed and cured in a foamy state, and I inadvertently My hand hurts when I grab it there
I thought I had to apply Paper to the paint from new to even it out
The part of Swing Arm ride, the paste is yellowish GBond The glue of the
Is there any other way, or at least don't stick out?
The Handlebar part that can be held by hand when standing is also a good idea, but it's a bit pricey If you think it's appropriate
View detail
Safe during maintenance!
I used to use two Uma for Vehicles, but they were not as stable as they could be
I have been able to maintain this STAND with peace of mind since I purchased it I should have purchased it sooner!
When you are not driving your car, you can put it on this STAND and look at your car to see the atmosphere in the garage I think the first time I saw it, I was able to buy it I can buy it for 1299 yen in real terms because I used webike's Point, and it is very I was grateful for the
This STAND is a mini type, so you need to lift up your rear and put it on STAND So the body of GORILLA is light, but the body of the GORILLA is caught in Smooth You may not get on the
View detail
To attach a vertical carburetor to MONKEY
I used it for 5LMONKEY at 12V
Down draftcarburetor (commonly known as the vertical) used in the old SUPER CUB (carburetor) I really wanted to try it on, and when I tried it, the gap between the Frame and I bought this one because I have very little and I can't physically attach a Power Filter or anything else to it!
The performance of SPTakegawa's Sponge type is more important than the performance of a short funnel It's like I bought it to put an Air Filter on
Therefore, it's not like the power went up dramatically or the high RPMs came around because of this I don't know
Still, it performed the function I needed it to perform well
I also thought the machining accuracy was high
I chose Gold alumite due to stock availability, but Black Anodized and regular It would be nice to have Silver anodized as well
It also has a split collar for the connection to the Carburetor It was, but not necessary for the vertical carburetor
Will it be necessary with a PC20 or something like that?
View detail
Oh well
I use it on the Grom 1 and it hits the bottom part of the headlight a little as it is It is not impossible to use it, but I extended it by welding the insertion part of the headlight It's ready to be used in a batch View detail
Price 〇!
I bought this for the Monkey engine replacement schedule in the spring.
I think that it is also a big success in the future Maintenance.
The last point price was also a little cheaper and the shipping cost was cheap and it was profitable.
View detail
Fits: Others
The price is cheap!
It's cheap! It's a bit heavy, and the finish is stubborn.
Well I do not mind the price is the price. I think that it is probably for mopeds, but there is also a little uneasiness in strength.
I feel that the Large type is strict.
View detail