Reviews
Measures to prevent hard to enter Neutral of Grom.
The Neutral on the Grom does not fit well, so I installed it to try it out.
I also exchanged the shift link at the same time, and what used to feel like a clunk every time I changed the shift, now goes in with a snap.
If we wanted, it would be better if the seals of the bearings were made of rubber seal (6902LLU) instead of gold (6902ZZ) to prevent rainwater intrusion.
I will use it for a while longer, and if the bearing is still stuck, I will replace only the bearing with one made by Rubber Seal.
View detail
Mounted on a return-type GORILLA
I did not want to damage my shoes when changing gears, so I attached them to the return-type GORILLA.
I feel some awkwardness in the foot placement of gear changing and footpeg, but I have no problem at all with this Change Pedal.
Thanks to you, Shoes is satisfied with the quality of the product without any damage.
View detail
Shift is now TIGHTLY
Shift is now TIGHTLY and easier to get into N.
There were instructions for installation, but there was no explanation of the parts to be removed, so I was a little confused.
It is also used with KITACO's Shift link.
View detail
Recommendation
The shift change is said to be a defect of the Monkey 125.
Especially after 1000km from the new car, it becomes harder and harder to enter Neutral.
It became Stress around 2000km.
When I put this product on and adjusted the Clutch a little farther, it was easier to get the GEAR in.
I don't have the Shift link and so far it hasn't been inconvenient.
View detail
I think it works.
I don't think that Shift feel has changed dramatically, but the state of not entering into Neutral has been reduced drastically, so I think it is effective. View detail
Easy DIY installation and safe for your wallet
Required tools are
・8,10mmRatchet
Extension bar of about 10cm
・5mmHexagonal Wrench
Drivers and radio pliers for removing split pins
1 pc of Pin2Φ12mm split with additional parts (Unnecessary if you want to reuse it)
Basically, only the Arm on the Shaft side and the ROD part on the Lever side need to be removed.
Loosen the 10mm bolt on the Arm side, and on the ROD side, flip the rubber cover and remove the split pin.
Remove the entire ROD from the Arm and remove the Bolt from the Crankcase (8mm) To Quantity:Remove 2pc
When installing the reinforced plate, it should be removed because it interferes with the Sprocket cover.
If you loosen the bolt on the bottom side of the cover installation, the plastic cover will bend to fit.
After that, just thread the PlateBody through the Shaft and fasten the supplied Bolt with holes with a 5mm HexaWrench and put it back together!
When you put the Arm back, the position is marked on the Shaft, so just put it back in line with the Arm cutout.
If you are familiar with the work, you can install it in about 30 minutes.
Shift feeling itself is not a bad unit to begin with. (Except for N) It didn't change that much.
If you want to have a Snap and Fee Ring, you may want to put it on as insurance.
View detail
A good, cheap product
Changed MONKEY's engine from 6V centrifugal clutch to 12V manual clutch I bought it from Timing, who put it on the market
Due to the cost of Engine and other Custom, I was looking for cheap parts and bought this one I did
There are many other expensive ones, but they are perfectly fine for a normal ride
The Hexagonal bolts that are tightened at the time of installation do not have a washer on them, and when you tighten them up, they are not attached to the bolts Wound will be attached
I have a separate Washer and use it together
It's a good, inexpensive product
View detail
Fits: HONDA GORILLA, HONDA MONKEY, HONDA CRF50F
It was used for the Chinese Minimoto of a CRF Copy with the retractable Kick pedal of the company.The quality of structure or a Plating is not good.It will be comfortable if it uses for a Chinese Motorcycle well.Since it is this price, there is no complai
It was used for the Chinese Minimoto of a CRF Copy with the retractable Kick pedal of the company.The quality of structure or a Plating is not good.It will be comfortable if it uses for a Chinese Motorcycle well.Since it is this price, there is no complaint! Some could be protected by this although a Shift pedal may hit and change into a rock or a tree during a run. View detail