Reviews
Fits: HONDA DAX, HONDA MAGNA50, HONDA Jazz, HONDA CD50, HONDA LITTLE CUB, HONDA SUPER CUB 50, HONDA MONKEY, HONDA GORILLA
Tune to Normal piston.
I used it to try to match a KITACO High-compression Piston, but the Tappet sound was so bad that I changed it to a …Normal piston and it was back to normal.
Apparently, it should be considered for Normal piston.
good point
Normal engine can be used for higher RPM.
It is not as good as KITACOSPL, but it turns okay.
Hill climbing performance is also good.
Cheap.
A bad point
Cannot be used for High-compression Piston.
The width of the Engine Spec. is narrow.
I think it is good parts if you want high rpm and high speed with normal engine.
View detail
Fits: HONDA BENLY50CD50, HONDA APE 50, HONDA MONKEY
Caution.
Purchased for HISATank for nsr50. At first it was good with no initial defects, but I took it off and stored it to repaint the tank. I asked a friend of mine who is familiar with motorcycles to take a look at it, and he said that the rubber packing inside was deflated by the gasoline when it was first used. I asked a friend who knows about motorcycles to look into it, and he said that the rubber packing inside had probably swelled up with gasoline when it was first used, and when it was removed and stored, it shrank more than when it was shipped. I ended up having to buy a new one. This was the first time I had ever had a cook that became unusable once the Gasoline was removed. View detail
Fits: HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
It leaked.
It started leaking 2 months after purchase. If it is bad, it will be a vehicle fire. I would like to have it replaced or returned Gold. View detail
Pilot Jet
I forget the number, but the hole was plugged. View detail
I can't install it
The position of the Bracket to the Frame is not right at all
Also, the intake is in a bad position and obviously not going to work
It's going to be just a decoration
View detail
It was no good
Quantity:Quantity in 1 Set of 6pcs:Set, but I was able to install Quantity:2pc. Set only. screw mountain defective. quantity:No sense buying it as a set I opened the package and even checked the installation so I couldn't return it I will repurchase another Manufacturer's one I learned a lot View detail
Fits: HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA dachshund, HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA dachshund
The quality isn't bad, but the adjustments are too Large strange
The quality is not as bad as what I imagined
As soon as you change the main jet and so on, you'll see the change in an easy to understand carburetor I think there is a
Also, if you say you're going to run even if it's appropriate, it will run, so you can make adjustments to your zebra
But the good thing is that there is not much adjustment which is the advantage of the carburetor's top-load only in Sole I can't
The reason is that it's not very well made in some places and it's a pain in the ass to adjust
The person who thinks about buying this considers the adjustment of the Air Screw to be troublesome, and considers the purchase of the thing with the resolution of being troublesome I think I'm doing it
It's true that the Screw from Takekawa makes it easier to use, but it's a little too tight to turn with your fingers It's not going to be a cakewalk adjustment
(A little more than $2,000 to go.)
Also, if you don't take the latest precautions when replacing the Slow Jet, the head can get twisted off in the the carburetor becomes Garbage in an instant
I will now Garbage 2 VM22's and waste the Gold amount that PB16 can buy and I did
I've only been playing with motorcycles for less than a year, so I thought there was the possibility of an installation error However, the #30 Jet goes in easily and the #27.5 etc. small stuff doesn't go in Considering, Screw may not be very accurate
It may be a problem with Jet, but I can't buy a third VM22, so I can't say for sure I can't say
I wouldn't recommend it, but if you still want to buy it, be careful with the Slow Jet replacement!
And don't buy the Minimoto Jet
I'm pretty sure it came from Posh, so you might want to use Solee
View detail
Fits: HONDA SUPER CUB 50Custom, HONDA LITTLE CUB
It was not necessary.
I was sorry..
Explanation I have read it properly,
Engine rotation does not rise, Bokoboko
It sounds like it is not more than 10 kilos just by being sounding.
I was afraid of abnormal appearance, so I immediately removed it.
What is it?
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA
I wore it but I got back to NORMAL with no good
Purchased for use with 12 V MONKEY Z 50 J.
I was exchanging various Parts at the same time, but after a while for a while (When Engine warms up) Idling is unstable and signal wait etc. The phenomenon that it stops at frequent occurrence.
Although I thought that setting of carburetor first though I tried variously, I came to be able to ride normally as I returned this Ignition coil to NORMAL, and I am relieved to understand the cause.
The price is less than half the OEM's price and Red is also good because it stands out, but I was stupid who I chose in appearance.
Perhaps it was Parts that happened to be out, but I will not purchase it anymore.
View detail
Fits: HONDA APE 100, HONDA APE 50, HONDA MONKEY, HONDA MONKEY, HONDA APE 100, HONDA BENLY50CD90, HONDA BENLY90 S, HONDA GORILLA, HONDA GORILLA, HONDA CUB-based Engine CL, HONDA CUB Engine CD
A different item arrived
This item was with Fuel Cock M 14 of MONKEY but things of M12 reached and could not be used
The bag containing the product was broken and it was not returned
There seems to be a problem such as other products also containing different products with respect to the middle goods
View detail
MINIMOTOMinimoto Magnet for MONKEY Engine
Oil At the time of replacement, I installed it, but if I do not make the tightening force considerably weak, it will be broken with a single blow.
Is it feeling to lock it loosely and secure with Wire lock?
Where there is a limit to weight saving ...
View detail
Mounting not
The one of the most standard Type arrived like the picture but the position of the Bracket in the attachment part with the Body is weird or the position of the suction Pipe can not fit in the fixed position properly.
It seems that there is no choice but to give up as it is not Gap that can be done with some processing ....
View detail
Turn half turn and finish - - -
I bought it to adjust the Pilot screw of NX 125.
Adjust as half turn "O, will it work?" I thought that the Driver did not rotate, and as I looked it,... Failed to buy. It is one word of.
View detail
When attached for the time being, the cut of the spline by the side of a kick was coarse, and it did not suit with the engine side spline and did not enter smoothly. Since it was unavoidable, a spline was united to some extent and equipped by a rubber ha
When attached for the time being, the cut of the spline by the side of a kick was coarse, and it did not suit with the engine side spline and did not enter smoothly. Since it was unavoidable, a spline was united to some extent and equipped by a rubber hammer. The pedal position of the kick did not become a right angle to the car doby this time and leaning to the front side about 20 degrees when a kick was opened in order to kick, since it was attached somehow... For the time being, I could kick and step on, but I had a sense of incongruity. I'm thinking to replace to the rusty kick attached before. Therefore, evaluation is one star severely. View detail