Reviews
MINIMOTO Regulator from 6V MONKEY Silicon Rectifier
I installed it on my 6V GORILLA, I bought it to customize it with 6V, the voltage is very stable and the battery life is longer. I will continue to ride on the Large Cutter while maintaining it. It has been my partner for more than 40 years. View detail
MINIMOTO 6V MONKEY6V MONKEY/GORILLA Main Harness
I purchased the 6V MONKEY/GORILLA Main Harness for MONKEY/GORILLA last time and this time I purchased this one because it comes with Silicon Rectifier Fire and the price is reasonable. I purchased this product because I can do the wiring without any problem. 6V OEM product is discontinued, so I am very thankful for this product. View detail
MINIMOTO6VMONKEY Silicon Rectifier Fire to Regulator
I have two 6V GORILLAs, so I installed the first one and the voltage became very stable and the battery life improved dramatically, so I installed the second one as well. I did not want to change to 12V, so I bought it to keep driving with 6V. View detail
Pimping to 12V square eye CHALY.
Fit is perfect.
Small is not wired.
The fact that it is made of glass is also an added bonus.
Chinese LEDs are installed on these to ensure brightness.
We had a good shopping experience.
View detail
Recommended!
Inexpensive and recommended!
Lens has been replaced.
View detail
Used to convert 6V vehicles to Clear blinker
[How is it used?
[Color] I changed to ClearEuropean Blinker and needed Orange bulb.
How was your experience with it?
Works fine. Unlike the cheap Orange bulb, the paint was well done.
How did it compare to other products?
I'm afraid you don't have to worry about 6V Orange bulbs because there are very few options.
View detail
Fits: HONDA MONKEY [Monkey] 5L, HONDA MONKEY [Monkey] 5L
Recommended!
Inexpensive and recommended!
OEMs are expensive….
View detail
Battery depletion and bulb breakage countermeasures!
I have the impression that the 6vEngine runs out of battery fluid quickly and is prone to bulb failure…
I was looking on the Net and found out that the voltage is regulated by Lectifire and Battery?
And my own tl50 that I got used had dried up Battery fluid!
This is why I decided to buy it to make it Regulator like a modern Motorcycle.
For MONKEY parts, but there are only 4 Wiring, and even if the shape of the Connector is different, it is only necessary to modify the Wiring, so I guess the threshold is low in this area (laugh).
tl50OEM Lectifirer is vertical and horizontalQuantity:2 pcs of Connectors could be popped in.
View detail
Fits: HONDA MONKEY, HONDA DAX
Cost-effective!
Used for GORILLA!
Just what I was looking for WITHOUT Reflector on the SIDE!
It is well made.
View detail
Minimoto6V Regulator
It is easy to install. Now I don't have to change batteries so often. View detail
Convenient Quantity:Set
CT110 HUNTER CUBCT110, purchased for 12V conversion.
It is a very nice product because there is no need to examine them one by one.
View detail
Useful to have
[How is it used?
I have been using Bullet Terminal for all of my Harness tweaking. Sometimes, when I have the motivation, I use AutoBacks and Color:I used to go to YellowHat to buy Coupler sets made by Emon, but it was a hassle to go buy them & expensive to buy them one by one.
Was the one you received as per Image?
It is just like the Image. Or rather, the quality is better than I expected.
Was the installation difficult?
Just turn the Wiring with Electric Works Pliers, Crimp and plug it into the Coupler.
It is useful to have a tool like this (https://www.webike.net/sd/2084789/) in case you plug it in by mistake. If you can pull it out cleanly, you can reinsert it.
How was your experience with it?
I no longer have to go out and buy every single thing, and I can put Wiring together neatly.
The fact that it comes in its own container is also a plus, as it saves me the trouble of going to the 100-yen store to buy Case.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
You can find other couplers from MINIMOTO (https://www.webike.net/tab/parts/bm/1409/br/1384/?q=%22%22&scls=2).
View detail
Old CUB confirmed.
The speedometer did not perform well for the increase in engine power, so I suspected that the cable of the speedometer was cracked and had to replace it.
It is indeed 20 years old, so it is not unreasonable.
good point
No installation hassles since it is OEM compatible.
● Accuracy seems to be good.
The price is also easy to buy.
It seems to be durable.
A bad point
Installation is a little troublesome.
If the speed and engine rpm do not seem to match on an old car body, you should suspect the Speedometer Cable.
View detail
That's the exclusive product
4LMONKEYHeadlight's Spring for fixing the Meter.
Since the spring has a rather special shape and the mounting place is Tight, it is safer to buy a dedicated spring than to make one by yourself. I wasted a lot of time trying to make my own spring once.
View detail
Universal Bellows Boots for Cable added to Clutch Cable
The NC750X has many areas of reduction in cost.
The clutch wire cable (let's make it hydraulic!) Dust Boots are also not included.
Both the Lever and Mission sides are bare.
The Lever side is made from Offfor Vehicle's Boots, but the Mission side is made from Bellows.
I found just the right one at Universal Product.
Minimoto's UniversalBoots with a total length of 50mm and a hole diameter of 3mm on the thin side (Wire side) and 6mm on the thick side (CableScrew part).
It was Exactly. I plugged it in while spreading it out without any processing.
This will protect you from rain, dust, etc. You can use it with peace of mind. I recommend it.
View detail
To install the MechanicalSwitch
I used it to convert the Zr-7S to Rear Sets.
I had been wondering what to do with the OEM parts for the Rear Sets, but there was no mount for the brake switch.
I considered getting a Hydraulic Switch, but I was hesitant because they are known for their high failure rate.
Thanks to this product, I was able to install the NORMAL Mechanical Type Brake Switch.
It is for MONKEY, but you can buy it for less than 1,000 yen, so you can use it for other than MONKEY.
By the way, I found out later that Kawasaki's ZrX1100 also seems to have these parts separately.
Maybe I should have done that since it's a Kawasaki?
I'll try to find the OEM Product number next time lol.
View detail
The poor electrical components of the 6VCUB will be slightly better.
When the battery gets weak, the headlight and tail lamp, which are directly connected to the generator When the battery is weakened, the headlight and tail lamp, which are directly connected to the generator, get a large voltage and run out of bulbs.
When I put this product in the wiring, it seems to prevent the voltage from flowing beyond a certain level, and the Valve is no longer out of bulbs because the voltage does not flow beyond its rating.
View detail
Ignition lock for Super Cab
I bought this ignition lock instead of the old one. the old one sometimes lost contact when driving over irregularities, which led to the fact that the turn signals and the display were turned off. The lock itself fit very well and the workmanship is very good, but the wiring needed to be redone as I have an electric starter. Therefore, the pins themselves had to be redone.
I recommend taking it if you have a problem or you have lost your keys. An inexpensive way to solve these problems.
-------------------------------------------------- -------- I bought this ignition castle in return old, because The old one sometimes moved contact when driving at irregularities, which led to the turning and display turned off. The castle itself approached very well and the quality of execution is very good, but the wiring needed to remake, because I have an electric starter. Therefore, the Pins themselves needed to remake.
I recommend to take if you have a problem or you lost the keys. Inexpensive way to solve these problems.
View detail
Fits: HONDA MONKEY
Used for MONKEY.
I used it for the Connector of the Tail part of MONKEY.
When you don't want to cut the Harness, you can use a thin slotted screwdriver etc. to hold the nail and remove and replace the Plain Type Terminal.
View detail
To Restore the old car.
SportsCUB (Old CUB with OHVEngine) used for Restore.
The Blinker relay was broken, although the electrical system would Restore with 6V.
If it's an old car, OEM Product might be the way to go, but I thought it would be good to revive the original function with a new one.
I'm relieved to know that the Blinker is firmly attached to the Wiring.
It's great to see you have a line up of valuable 6V products.
View detail