Reviews
Fits: HONDA MONKEY6V, HONDA MONKEY6V
’Type 74 MONKEY
Personally, I dislike Minimoto products. But this parts is very similar to the ones I had back then, no complaints! I will report any changes after that. View detail
Not usable !
This decal for Honda Monkey Z50J1 Restauration ist not usable. IT`s a simple, low cost, thin decal. Not the 3M Laminat as mentioned. The orange color is faded. I will throw it in the bin. Not usable View detail
Moped Type 2 Display Sticker
For the price, it was a good one.
Durability will be verified in the future.
View detail
Motorcycle has been revived.
It had been in garage storage for more than 30 years since I bought the car, and the sticker had started to peel off. I found this product on webike by chance and bought it immediately. View detail
Bad hole position in Bracket.
The position of the hole in the bracket was not good, so I could not put it on with a pop.
It looks like I need to widen the long hole in the Bracket or shave the Bracket.
I chose the latter.
I think the texture is quite good.
View detail
The front will be tightened.
It would look great on a Honda 4minifork! View detail
Parenthesis is better?
My GORILLA has a carrier for the front basket, so I used a hexagonal spacer to lower it by 20mm. View detail
high
Good design. Easy to install with Bolt On.
But it's expensive!
View detail
It looks tighter.
As others have written, it tightens up the look.
It's a bit stiff and the mounting is a bit odd, but it's solid.
Even if you push it in with force, it won't break.
I put it on the X4LD as well as APE, but the screw holes are just right.
I was able to pimp it out because it was there.
View detail
Front fork!
I bought and installed this one as Accent The look and design is good
I made a hole in the bracket sleeve part because it was a little off the threaded hole
There were no problems with the rest of the installation
View detail
Car grades Up
I bought it by looking at the comments of others, it was OK because it was hard to enter Grommet because it was installed, it was OK if it was dipped in hot water for 5 minutes, Dress-up parts but the texture was high and the car case was up I feel like.
Should it be a little cheaper?
View detail
Easy Dress-up possible!
SP made by Takegawa φ27 Front fork (Old model) It attached to.
Material : I felt hard when I attached the RubberGrommet to the Bracket, but I managed to insert it as I pushed it with the nail.
Emblem simply inserts the protrusion on the Reverse side into the Grommet.
For mounting on the car body, it is easy to use Bolt for OEM Fender and Stack to stop Bracket Screw..
I stopped Screw with Emblem attached, so I was able to grasp the interfering part. (Adjust Horn's Stay length as Horn was interfering. )
Easy to install, I was satisfied because I was able to Dress-up.
View detail
To MONKEY!
I mounted the classic Emblem.
Because the position of the Bracket hole did not match, we made a little elongated hole and installed it.
Emblem itself was not a problem.
View detail
Honda emblem
Got the 3 Honda badges. Took a little longer. But it wasn't because of Webike but because of the German customs. It was there for a long time. The emblems are all fine. Am happy. Thanks greetings Sven View detail
It's a classic but satisfied with it
It is good that the gap under Headlight fills up.
It's a classic Custom, but it looks nice..
Since Horn interferes, it is necessary to shift the position, but it is easy because it just changes the position of the hole.
View detail
Emblem is the best.
"Small" I installed it, but it is nice. Because I turned on Down fender, I lighted but I was lonely, but I feel tightened when Emblem is attached. I like it. It is easy to install, it was attached without any processing etc. View detail
We replaced Emblem from Small to Large.
I was wearing EmblemSmall so far, I wanted a little more presence and replaced it for Large. This product, Bracket installed is Stainless Steel Very texture is very satisfied. View detail
CB 750 FOUR concession
Because something around Front felt lonely, if you are looking at the age of love the eldest son, Lame Ki! Buy it on the second son love machine! Tightened looks best! View detail
APEHONDAEmblem(Large)&Bracket
By doing Front Down Fender, I was concerned about Light and HONDAEmblem (Large) It was solved by installing & Bracket. I made it solid and changed to Large people's impression. View detail
Simultaneously worn with Bates light
Attached to APE.
Since my APE is braiding Bates light, purchase with processing premises that there is no possibility of mounting unprocessed.
When I looked at it together, I could mount it with no machining if I upside down Bracket. Although it was able to be installed, it becomes a place that is lower than the original attachment position, so Stem can be seen, and it may be better to process a person who is interested.
View detail