Reviews
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA
I've always wanted one of these!
For maintenance work around the rear, I used Maintenance STAND to float the Rear Axle, but my 4MINI "APE100." When "Gorilla Kai 88." In this case, GORILLA with 8-inches wheel is more unstable than APE with 12-inches wheel because of the swing arm angle of 4?
webike's. "Model." I was just casually looking around using the product search function on each page, and I found it.
"Center Stand!"
Buy it immediately! Yamato delivered it to me at exactly 19:00 on the next day with a 19:00-21:00 arrival time.
I unpacked the bike, removed the NORMAL from the unstable maintenance stand, replaced the side stand, wrapped the frame with gummed tape for waterproofing and tie wrapped the frame with the switch that I forgot to put back on the side stand. and tighten 4 mounting bolts with 13mm socket wrench, installation was completed before 21:00!
Fast, cheap, good, and convenient, just like a beef bowl at YOSUNOYA!
This Main・STAND Return・Spring is properly double wound and carefully finished.
However, there is no bar to step down with your foot when you stand STAND, so you need to stand STAND by holding it with your foot behind the ground point of STAND like you stand both legs STAND of bicycle.
Tools are easy if you have Spanner or Socket Wrench and Spring Hook.
In the case of a machine equipped with a Rear Box, such as our GORILLA, the front wheels may become floating when the Main stand is set up because the Rear is heavy.
View detail
This is good!
I use Z50JMONKEY for commuting, but the parking lot of the station is too small and I wanted Center Stand, so I looked for it. This time, I chose the one with OEM footpeg and Side Stand. The Center Stand makes a gap between the rear wheel and the ground, so maintenance is easier. However, I think that it is not possible to install it if the Rear is made into a wide Wheel. I am grateful that Bolt and collar are attached so that I can use either 8Inch or 10Inch. View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA
It came on without any discomfort.
It was installed as usual. It was easy to install as long as the existing parts (STAND) were removed and the vehicle was supported. View detail
SIDE & Main stand is very easy to use.
The standard 12VDAX is Main stand only.
I think the Side Stand is more convenient for city riding.
However, with Honda OEM, there are only two options, Main stand only or Side stand only.
So I bought this product.
This is a one-stop solution. After all, the usability is preeminent when there are both Main & SIDE.
The main stand part will interfere with the chain if you install it by itself.
So, after installing it temporarily and seeing how it looks, there is Screw to adjust the height of STAND to jump up.
Interference with the Chain can be prevented by adjusting the amount of Screw protrusion.
Also, since the footpeg part becomes Foldable, it is safe even if it catches on the hem of Pants or something.
However, it's still a mess to make.
It is also recommended to disassemble and grease up the shaft and the base of the stand before installing.
View detail
It's not bad
In order to install it, the bolt holes
There is some gapping and processing.
It was necessary.
Stand stopper Rubber.
It's too thick and the main stand is halfway between the two
I shaved off half of this one to come to a position.
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA
Cheap and fully functional
It can be used in conjunction with SIDE, and I think it's the best of all worlds without any buffering from the others
Put the OEM Side StandAlarm feature, Unit, in space behind the Engine You can always put NORMAL back in if you use Tie Wrap to hold it in place, and it's a feature you won't be using anyway Then it won't be a problem to cut it off
View detail
Good quality, but heavy weight
The MINIMOTO DAX Stand & Footpeg is a good quality item. Had mine for several years, and the metal, paint and rubber is still holding up as good as any OEM Honda parts. It's very solid, but a downside is high weight. I guess the metal contains a lot of iron, and it could/should have been produced in a lighter steel metal blend. The weight is not that bad if you remove the center stand as I did. I also think it looks better that way. But keep the center stand laying around, it's very handy and quick to attache if you need support for the bike when removing any of the wheels. View detail