Reviews
Side Stand Length Adjustment
I have been using their 275mm for MONKEYAluminum side stand on my RZ250R, but it is too long and seems to fall over against me, so I bought this one, which is 20mm shorter.
Note that the bolt is fastened from the reverse side, so it cannot be attached unless there is space on the reverse side.
The RZr cannot be fitted with the supplied Minus Volt because the chamber gets in the way, so we used an OEM Hexagon Bolt and managed to fit it.
As a result, installation was no problem at all, but Alignment was almost the same as the 275mm STAND.
Was the original Aluminum Stand scraped and shortened?
Well, this is also the best part of the actual matching diversion.
Good thing it was inexpensive.
View detail
Fits: HONDA MONKEY (FI), HONDA MONKEY (12V), HONDA GORILLA (12V), HONDA MONKEY 3.1PS (6V), HONDA GORILLA 3.1PS (6V), HONDA MONKEY 2.6PS (6V), HONDA GORILLA 2.6PS (6V)
KSR80 Sides Land
I was wondering if I should paint it or replace it with custom parts, but this product looked like it could be used, so I bought it at my own risk. I was wondering if I should paint it or replace it with custom parts.)
It was almost the same length as the OEM one, but the KSR one was slightly angled at the base, and that was the part that bothered me.
The KSR is located on the outside, so you will need to modify the screw so that it is on the front side.
Also, although the screw size of the mounting part is the same, the Bolt of this product cannot be used (it can be used if the diameter is made smaller), so I used the KSR OEM as is.
This product has a zagged surface, which interferes with the flange of KSROEM's bolt with flange, and the shaft of this product's screw is large, so the hole on the outside is between φ1 In order to use KSR's screw, you need M10 Washer or Spacer that can fit in the counterbore. If you want to use KSR's screw, you need M10 Washer or Spacer.
I used a grinder to grind off a portion of the product so that the KSR Bolt flange would not interfere.
I also adjusted the thickness of the Washer.
When I raised the stand, the position of the end of the KSR would interfere with the Swing Arm, so I set the tap up so that it would hit the end a little closer to the end and adjusted the stop position with the bolt.
That way, interference was avoided.
Lastly, the lack of an angle makes the vehicle more upright when the STAND is applied compared to the OEM.
It took a little work, but I was able to install it successfully.
Diversions are at your own risk.
It looks great and I'm personally satisfied with it.
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA
10InchMONKEY
10InchTire.
10cm Long Swing Arm, 280mm suspension.
This Spec. is the shortest and just the right length.
If you look carefully, the texture is worth the price.
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA
It came on without any discomfort.
It was installed as usual. It was easy to install as long as the existing parts (STAND) were removed and the vehicle was supported. View detail
SIDE & Main stand is very easy to use.
The standard 12VDAX is Main stand only.
I think the Side Stand is more convenient for city riding.
However, with Honda OEM, there are only two options, Main stand only or Side stand only.
So I bought this product.
This is a one-stop solution. After all, the usability is preeminent when there are both Main & SIDE.
The main stand part will interfere with the chain if you install it by itself.
So, after installing it temporarily and seeing how it looks, there is Screw to adjust the height of STAND to jump up.
Interference with the Chain can be prevented by adjusting the amount of Screw protrusion.
Also, since the footpeg part becomes Foldable, it is safe even if it catches on the hem of Pants or something.
However, it's still a mess to make.
It is also recommended to disassemble and grease up the shaft and the base of the stand before installing.
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
Cosmo!
Purchased in a hurry due to the replacement of the rear suspension. There is a Wallet situation and this product was chosen.
I installed it on a 280 suspension with an 8InchFront 4cm and a 10cm Long RearMinimoto 10cm Long, and although the base is a little unlevel, it works perfectly fine as a STAND.
For the price, it's more than I expected!
View detail
Fits: HONDA MONKEY (FI), HONDA MONKEY (12V), HONDA GORILLA (12V), HONDA MONKEY 3.1PS (6V), HONDA GORILLA 3.1PS (6V), HONDA MONKEY 2.6PS (6V), HONDA GORILLA 2.6PS (6V)
The shine of light and aluminum is beautiful STAND!
important item
[Was there anything that disappointed you?
The use of this product is not compatible with the Material:It was easy to work with aluminum, and it was as expected
Do you have any wishes or improvements you would like to make for the Manufacturer?
I think it would be easier to purchase a non-conforming product if information such as the diameter of the mounting bolts were included
[Do you have any products to compare it to?
The company's steel Side Stand, which I was worried about because of the many variations in length
Frequently Asked Items
What made you decide to buy?
Material:Because it is made of aluminum, it is easy to process, light and looks good It was beautiful and the price felt right
How was your experience with it?
The Bolt of the spring hook was moved to the other side of the spring hook because it is not applicable, or the ground surface was shaved We have done a number of things, including the following, but the Material:Aluminum was easy to work with
Was the installation difficult?
I was able to use it on a car model that is not applicable with the above minor modifications
【Please tell me the installation point and hang】
Screw is provided to prevent the Large trapezoid bolt from loosening After the last tightening, the screw should be used to prevent the Large Clamp Bolt from loosening
[Was the Instruction Manual easy to understand?
Easy to install for simple Parts, no need to look at the Instruction Manual It was
[Included Parts:were they on?
Spring, Large Bolt, Screw, Spring hook Bolt It consists of
[Others]
I was lucky enough to be able to use it even though it was not applicable The Side Stand is as light and beautiful as it looks, and I was able to install it
View detail
Side Stand's Repair Parts
I used it on a CD125T Custom vehicle
i was able to use the Side Stand for MONKEY, so I guess Spring is the same I bought it for a simple reason or an idea to say
It's only Spring, so it's manageable for a slightly shorter amount of time
It's no good if it's too long to serve, but …
The result was Large correct
It was uneventful to use and installed normally, not too long or too short
It's not a product that will get much sunshine if you're a normal custom motorcycle But if you're building from a Frame, you may be in trouble because of the lack of detailed Parts
If I had the gold, I would buy new OEM parts, but if the dust piles up, so does the The gold amount will be a great amount of money if you buy a lot of things
You can also buy used ones, but they will not be as cheap as they are in the end because of the shipping costs, so we're going to have to make these kinds of fine products It would be very helpful to have it
The products of Mr. Minimoto can be made by the things like CHINA and Made in Taiwan Our Gap rate is low, so we will continue to utilize it in the future
View detail
*for MONKEY
As the product name suggests, it's for MONKEY
I used it on my CD125T
Honda's SmallEngine Displacement Volume vehicles are Large bodies I tried it because it's the same, but it was pontooned
… but after a year or so of use for a vehicle that weighs more than 1.5 times as much as the car, it bent into a gnarled shape I'm done
Fortunately, we were parked near the wall so there was no Damage to the vehicle, but everyone be careful about diverting it! Let's laugh
It's not a bad product by any means, so if you're around MONKEY, DAX, or CHALY, you'll be able to find it I don't think it's a problem
View detail
Cost performance is good!
Tire size was changed because the leaning at the time of stopping also became large when the tire size was made large It was
The size came in a variety of sizes and it was just perfect
The length is about the thickness of the foot, so it's about the Plus5mm shown
View detail
Well, it's better than nothing
It's better than nothing
About the 4th Tire replacement, a hole will be made and Wound will be attached to the Rim
I'm sure I have my own skills, but I'm surprised at the wear and tear
The price is reasonable, so I'm going to REPEAT it myself
View detail
There is no problem..
I bought it with a dubious semi-confidence because it was cheap, but it will function as a firm Spring. Half years use, Rust occurred, but the price is also reasonable, so it is a reasonable range. View detail
With 10 IN dedicated STAND!
By the time we customized it 20 years ago, we only had an expensive Side Stand of a famous Manufacturer, so we extended the Side Stand for 8 Inch by welding
But since this price, we purchased immediately without thinking welding etc.
It is a place to worry about the strength of the ground contact area and the feeling of painting, but I would like to check it in the future
For 10 Inch, 12 cm Long, 300 mm Shock combination, it was Side Stand with a good slope
View detail
Fits: HONDA MONKEY (FI), HONDA MONKEY (12V), HONDA GORILLA (12V), HONDA MONKEY 3.1PS (6V), HONDA GORILLA 3.1PS (6V), HONDA MONKEY 2.6PS (6V), HONDA GORILLA 2.6PS (6V)
It was a nice shopping experience..
It is heavier than I thought, I think whether durability is a problem. I am very satisfied because the price is not high so far. I will also order again if I also buy next time. View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA
Used for CHALY
As car height increased with CHARY's Rear shock change, NORMAL STAND was looking for an adjustment formula because it is too inclined. I think that quality is a price. Adjustment accuracy of Screw part - Finish is hard to feel. I am worried that Spring's catch is shallow. View detail
It's about a little longer.
OEM rusted, the ground part became ragged, so I replaced it for this product. Compared before and after exchanging, it became a bit more straight after replacement, so it feels longer than OEM.
There is no problem for use
View detail
[Webike Monitor] Since it was used in combination with the STAND Stay of G Craft, even the specification of 10 inches is a vertical state mostly. Since it was suitable even if it considered the processing raw material, since it was this price also in
[Webike Monitor] Since it was used in combination with the STAND Stay of
G Craft, even the specification of 10 inches is a vertical state mostly.
Since it was suitable even if it considered the processing raw material, since it was this price also in
, it processed and adjusted.
View detail
Fits: HONDA MONKEY (FI), HONDA MONKEY (12V), HONDA GORILLA (12V), HONDA MONKEY 3.1PS (6V), HONDA GORILLA 3.1PS (6V), HONDA MONKEY 2.6PS (6V), HONDA GORILLA 2.6PS (6V)
[Webike Monitor] It purchased as an object for DAXs which exchanged the Rear suspension for the long thing. Although not attached, I still think that a Quality is high with considering a price. That is a little sorry for the portion of Spring
[Webike Monitor] It purchased as an object for DAXs which exchanged the
Rear suspension for the long thing.
Although not attached, I still think that a Quality is high with considering a price.
That is a little sorry for the portion of
Spring receptacle to be Bolt appropriation.
If the
Spring washer etc. are not made to bite, it is the touch from which it is likely to loosen and escape.
View detail