Reviews
Fits: HONDA SUPER CUB 50, HONDA CHALY 70, HONDA CHALY 70, HONDA CHALY 50, HONDA CHALY 50, HONDA CHALY 50, HONDA SUPER CUB70, HONDA SUPER CUB70, HONDA CHALY 70
The quality is not good
It's thin and cheap, it's going to cut my hand and Gasoline is going to leak.
If you want to pay $1,000 for this, you might as well buy an OEM keyless Cap for $1,500.
View detail
Not usable !
This decal for Honda Monkey Z50J1 Restauration ist not usable. IT`s a simple, low cost, thin decal. Not the 3M Laminat as mentioned. The orange color is faded. I will throw it in the bin. Not usable View detail
Fits: HONDA XR100MOTARD, HONDA XR50 MOTARD, HONDA NSR80, HONDA NSR50, HONDA SUPER CUB 90, HONDA SUPER CUB70, HONDA SUPER CUB 50, HONDA APE 100, HONDA APE 50, HONDA DAX, HONDA GORILLA, HONDA MONKEY, HONDA glom
Fixing plate defective
Fixing plate could not be installed and we had to use the previous Plate.
If you want to purchase this, you normally recommend KITACO.
View detail
Fits: HONDA DAX, HONDA MAGNA50, HONDA Jazz, HONDA CD50, HONDA LITTLE CUB, HONDA SUPER CUB 50, HONDA MONKEY, HONDA GORILLA
Tune to Normal piston.
I used it to try to match a KITACO High-compression Piston, but the Tappet sound was so bad that I changed it to a …Normal piston and it was back to normal.
Apparently, it should be considered for Normal piston.
good point
Normal engine can be used for higher RPM.
It is not as good as KITACOSPL, but it turns okay.
Hill climbing performance is also good.
Cheap.
A bad point
Cannot be used for High-compression Piston.
The width of the Engine Spec. is narrow.
I think it is good parts if you want high rpm and high speed with normal engine.
View detail
Fits: HONDA BENLY50CD50, HONDA APE 50, HONDA MONKEY
Caution.
Purchased for HISATank for nsr50. At first it was good with no initial defects, but I took it off and stored it to repaint the tank. I asked a friend of mine who is familiar with motorcycles to take a look at it, and he said that the rubber packing inside was deflated by the gasoline when it was first used. I asked a friend who knows about motorcycles to look into it, and he said that the rubber packing inside had probably swelled up with gasoline when it was first used, and when it was removed and stored, it shrank more than when it was shipped. I ended up having to buy a new one. This was the first time I had ever had a cook that became unusable once the Gasoline was removed. View detail
It was good when I first bought it.
I purchased this product because the Cell Motor of Co-MAJESTY had difficulty turning.
It was good for a little over 6 months, but gradually started to not work at times.
Just one year later, he passed away as his life span seemed to have come to an end.
View detail
MONKEY
Blinker became unusable due to a broken bulb while driving on a farm road. View detail
It has a higher percentage of glass fibers than Titanium, and the manufacturer knows it, but they sell it as TitaniumVantage. Vinyl gloves are included with the product. View detail
Fits: HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
It leaked.
It started leaking 2 months after purchase. If it is bad, it will be a vehicle fire. I would like to have it replaced or returned Gold. View detail
The hole position is …
It was the first time for me to use Minimoto's product, but as other people said, the hole position was not correct and I couldn't fit the bolt. It seems to be no problem to use, but I would like to have it made more firmly. View detail
Fits: HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY
All lies.
Anyway, the welds are so bad that even compatible models can't be pimped out, and it interferes with the rear suspension, and the angle of the inserts on the engine side don't match, so I'm just laughing. (Lol) If you buy this, you must have both Hand Bent on the Engine side and Hand Bent on the Silencer side. I can't get the Hand Bent so I'm using only one side of the Bolt on the Engine side and forcing the back of the Bolt to be spread outward, but I'm not sure if the back of the Bolt can handle the exhaust leaks and the impact of driving. I really wish I hadn't bought it. View detail
Pilot Jet
I forget the number, but the hole was plugged. View detail
Fits: HONDA XR100MOTARD, HONDA XR50 MOTARD, HONDA NSR80, HONDA NSR50, HONDA SUPER CUB 90, HONDA SUPER CUB70, HONDA SUPER CUB 50, HONDA APE 100, HONDA APE 50, HONDA DAX, HONDA GORILLA, HONDA MONKEY, HONDA glom
I bought this with the intention of using it with nsr80 but…
The groove of the fixing plate is too large to rotate, so I could not install it.
I wonder if it can be installed on a MONKEY engine.
View detail
Fits: HONDA MONKEY, HONDA GORILLA
I was injured on Edge.
This is a lousy product. I cut my finger on the edge when I turned the device with my bare hand. I have a lawsuit on my hands. View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA DAX, HONDA CHALY 50
The length of the Axle Shaft is not enough.
I thought I could install it right away, so I pulled out the Axle Bolt without curing the wheel. When I installed the AxleBolt, I found that the Ring part of the Chain Adjuster was too thick and the Axle Shaft was not long enough. I gave up using it in the end... I don't know why they sell products that can't be used, but it was a pity... I think it was a bad idea to order it without thinking about the size etc. because it was a compatible part... Please be careful when you order. View detail
Fits: HONDA GORILLA, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA MONKEY
I was hoping for parts...
I used it to service my 30 year old GORILLA. I had very high hopes for it, but it was returned in tears due to initial defects (oil leaks, bad parts)! 。 I'm glad that the return was handled properly, but I was disappointed with the parts I was expecting:・・・・ View detail
disposable
It is used with the D Tracker 250 and has a chain size of 520.
It broke after one use.
Originally I would have liked to return it because it was defective, but the price was low and I was able to crimp it, so I give up.
View detail
There is no one type of conversion adder included
The photos of the delivered parts and Catalogue photos were attached to the mail, but we exchanged emails 4 times It seems that even in the It seems that it is not possible to create a fault component in the following ways:”” View detail
It's not strong enough
The bracket broke after 200km or so, even with the silencer band It's not strong enough and the bracket is not thick enough
I had no choice but to scrape off the original bracket and use Silencer bandQuantity:I use 2pc and make a Bracket on the body side
View detail
I can't install it
The position of the Bracket to the Frame is not right at all
Also, the intake is in a bad position and obviously not going to work
It's going to be just a decoration
View detail