Reviews
Installation is easy
Installation is easy, as long as you follow the instruction manual. View detail
To avoid contamination from mud splashes.
The Fender is now long enough that there seems to be a mud splash effect.
It doesn't look that noticeable.
If you can remove the front tire and work on it, I think you will have no trouble installing it. As mentioned in other people's impressions, if you can do it for a few thousand yen, it would be better to ask a shop to do it for you.
Why ask for Shop?
1.If you only remove the Fender and work on it, it is quite difficult to put it back together. (I dropped the Fender before tightening it with Screw and scratched it, though it is now polished with Compound and not visible from a distance.)
2.It says to drill a hole in the Fender and install the pin that comes with it, but I decided not to do that because the material of the OEM Fender is steel plate and it would be difficult to drill a hole in the curved part with a drill, and also because I thought it would look uncomfortable. I would recommend shop installation for this reason.
Extender Fender is now installed using only the double-sided tape provided.
I gave it a 4 because of the difficulty of installation and the fact that I haven't actually driven in the rain. I gave it a 4 because of the difficulty of installation and the fact that I have not actually driven in the rain.
View detail
Fits: HONDA NT1100, HONDA CRF1100L AfricaTwin
Large screen size is not just Film
[How is it used?
Introduced to protect expensive Touch panel.
Was the one you received as per Image?
It is slightly smaller than the Large size on the screen.
Was the installation difficult?
It was somewhat difficult for a beginner like me.
Especially the positioning and dusting.
How was your experience with it?
The screen is less reflective, but it does not completely reduce reflections. (I guess that's to be expected.)
[Included Parts:were they on?
AlcoholWipe, Squeegee, Dust Removal Seal, Instruction Manual, and everything else that usually comes with the purchase of a protective film for smartphones.
[Was there anything that disappointed you?
As stated in the title, it is a little small for the object (screen) to which it is pasted.
Point and hang of installation
Do not try to install it using only the accessories, but use a solution of 500?water and a few drops of neutral detergent in a misting sprayer to apply it.
Dust is difficult to get into and easy to position.
Youtube, etc. How to apply protective film I think it would be better to search for a place to start with and then try to imitate it.
[Notes]
As I have mentioned many times, the film is a little small for the screen.
(If the film is larger than the object to be pasted, the edge of the film will float. In short, it is a matter of precision.)
Note that this is mentioned in the Instruction Manual, but not in Webike's product description.
[Opinions and requests to Manufacturer
Please improve the accuracy of FilmCut and come out with a product that can cover the entire screen.
View detail
Fits: SUZUKI Hayabusa
Wound Prevention
I put it on to prevent scratches on Meter.
It was already attached when the car was delivered, so it is not on the road without being attached.
There is no foggy feeling, and the transparency is so high that it is easy to forget that it is there at all.
Also, two sheets are included in the package, so there is no need to worry about reupholstering or making mistakes.
However, it would be better to remove the Meter from the car body when attaching it, and to do so with a Single Body.
View detail
Mudguard on bmw r1200r
Installation is a simple process of attaching with the included double-sided tape.
Effectiveness.
Small stones and mud rolled up by Front are reduced.
If only it were a little longer? 5.
View detail
Fits: SUZUKI V-Strom 250, SUZUKI GSX250R
So-so.
I bought the Motorcycle new and it was scratched from the start.
I was worried that I wouldn't be able to apply it properly and neatly, but I was able to apply it in the same way as I do with my smartphone. Once I was able to put it up well. Sweat
I don't know about durability, etc. yet, but this time I put non-glare on it.
If there is deterioration, etc., another one. [Color] I will put up a Clear.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z650RS
Meter panel protective film to protect from scratches
Asking PRO to protect the Meter panel just in case it seems to fail to stick.
The workmanship is good, but I am not very satisfied with the overall cost performance, including the labor cost.
About the contents of the product, 2 FilmQuantity:It is a Set, but Antiglare is not necessary and two Super clear cards are fine.
If you fail, there's always the next time ….
View detail
Fits: SUZUKI Katana, SUZUKI GSX-S950, SUZUKI GSX-S1000, SUZUKI GSX-R1000R L7
Price suitable
It was put up at the same time as the car was delivered.
All Quantity:It comes in a set so it can be applied right away.
I don't think air will get in unless it is very messy.
However, the visibility will be adequate.
Do you want to see the OEM intact and clear, even if scratched?
Do you want to endure the visibility and continue to ride in peace?
Can it be scratched in the first place?
I feel safe. (Insurance for the mind) I chose the
View detail
Fits: YAMAHA Tracer 9, YAMAHA Tracer 9 GT, YAMAHA XSR900
I don't want to mess up my Rear shock.
I installed it because I was concerned about the mud that would roll up on the rear shock. The texture is good with no difference in appearance from the Rear Fender. The installation was easy with double-sided tape, but it is necessary to use a drill to install the pin to prevent the pin from falling off. I think it is necessary to install the pin because the edge of the pin was slightly lifted after about 2 weeks. View detail
Fits: HUSQVARNA Vitpilen 701, HUSQVARNA Vitpilen 401, HUSQVARNA Svartpilen 701, HUSQVARNA Svartpilen 401
Before the scrape gets in.
I purchased this for Svartpilen 401 2021.
The Meter surface of this MODEL is a MATERIAL that could easily be scratched if rubbed with sand and dust.
If anything goes wrong, it will be a very noticeable area, so it would be good to deal with it as soon as possible.
While Film seemed to be firm and thick enough to protect it, its strong resilience gave the impression that it was a bit difficult to apply.
After applying the first sheet, I realized that it would work better if I positioned the corners, lightly fixed the position with masking tape, and then started peeling off the backing.
It's a micro-small bubble, so that's good, but I plan to do so the next time I reupholster it.
Since it comes in a two-pack, even if it fails a little, there is peace of mind knowing that there is always a next one.
If it were a little cheaper, I would give it a perfect score.
View detail
Fits: HONDA XL750 Transalp, HONDA X-ADV, HONDA FORZA 750, HONDA CB750 Hornet, HONDA CB1000R
Should be put up at the time of a new car.
It also comes with a fine outer bag, a dust remover Seal and CROSS when pasting.
I don't understand why glare and Antiglare are combined, they should be sold separately.
The edge treatment and shape are highly accurate, and the Small anti-scratch effect is outstanding, so I wanted to put it on when the car was new.
I don't know about durability. If it is bad, I will add a note.
View detail
I was able to charge the battery normally.
We used Rocket3gt's Standard Equipment, Heller Socket, to charge our phones.
This is just an imprementation after using it for a short distance to check the operation.
The phone (Android device USB-C) charged well.
I am concerned that the Heller Socket may come out due to vibration or bumps because of its loose insertion.
The Rubber cap is also a little loose and I am worried that it will be blown away by the wind.
While the Heller Socket is inserted, it glows Blue, but with rocket3, you can't always see the glowing slot due to the angle of the rocket.
I would not want to waste power consumption, even if it is very weak, so I think it is unnecessary for me.
Also, you can't (or don't want to) leave it plugged into the Motorcycle at all times, so you need to carry it with you.
In that case, I think it would be helpful if the size were a little smaller.
If there are any changes in the evaluation to match the actual conditions of durability and a little more severe use, we would like to reflect them at a later date.
At this time, we have determined that the product is cost-effective with no fatal product defects.
View detail
Fits: YAMAHA YFZ-R7
Scratch prevention!
Meter surface was commented to be easily scratched
I purchased and installed it since it is a new car.
Seat is Quantity:1 Set of 2pcs.
Other, Surface Cleaning sheet×Quantity:1 pc.(same as anti-fog for Glasses?)
ditto mark Cloth×Quantity:1pc.
ditto mark Stretching pattern paper (Material):(Plastic)
Instruction Manual (Translation (please enter here))
View detail
Fits: HONDA REBEL 250, HONDA CL500, HONDA CMX500 REBEL, HONDA CL250
If you want to use your Meter for Beauty, it's Recommendation!
This is the OEM version, but I will post it as a reminder of how it feels to have it installed.
Purchase and installation should be done at your own risk.
Installation time:10 min.
Required tools:WetPaper (included), dusting sealet, etc.
? Place the protective Seat on the Meter and hold the Paste Image.
? Wipe with WetPaper→CROSS until you feel comfortable.
? Remove the entire area with a dusting Seal.
? Peel off about half of the first Seat of the protective Seat and decide the position for pasting.
? Paste while rubbing with the attached plastic board etc. so as not to leave air bubbles.
? If air bubbles remain, try rubbing them with a plastic plate, etc. to see if they disappear.
If not, peel off the tape with Seal or Cellophane tape and reattach it.
? In case of dust, peel off to the relevant area and remove with a dust remover seal.
*It will be an outdoor job, so if you don't work on SPIDI, a lot of dust is likely to get in.
I stuck it on after a month of purchase because I was concerned about dirt and scratches on the Meter.
A minor scrape or two is no longer visible.
Some of the ones I purchased on Amazon were quite SmallSai protective Seat, so please be careful when purchasing (it said it was for Rebel 250).
View detail
Fits: HONDA NT1100, HONDA CRF1100L AfricaTwin
Strong reflection
Transparency and [Color] Smoke and Quantity:Cost performance is high since it is 1 set of 2pcs. I think this product is useful for preventing wound. View detail
Fits: SUZUKI Katana, SUZUKI GSX-S950, SUZUKI GSX-S1000, SUZUKI GSX-R1000R L7
Visibility is somewhat reduced.
It will be somewhat difficult to see, but I think this is something that can be solved by getting used to it.
Installation is very easy, but the Instruction Manual will help you to "Blue" (Sealetc.) is probably the one labeled "Black" I think it is a good idea.
However, it is easy because all you have to do is wipe the Meter clean and apply it.
I had a little air in it during the application process, but I was able to remove it by lightly rubbing it and pushing it to the edge.
It is not SUPERJUST fit, there is some gap, but I personally don't mind it.
View detail
FenderExtender on the grom
I purchased these to reduce mud splatter on my Horizontal TypeEngine when I bought my Grom new. I used 3M double-sided tape instead of the supplied double-sided tape for installation. It has been 7 years and 56,000km since I bought it and it has reduced the mud splatter without any deterioration. I thought that the cost performance might not be so good, but I have not had any problems for more than 50,000 km, so I felt again that it is a good product. View detail
Mud Splash Prevention
It arrived today in the morning, no problem to check the product, I temporarily matched it to the Fender and it fits perfectly, it looks like an OEM Product, it is thick and solidly made, it is a down fender made by KITACO and the Fender is down, so I am not sure if the Fender is down or not.
After removing the fender and cleaning the mounting position, I attached the double-sided tape (uneven cut) from the Included Parts:section to the fender side and then attached it to the plating fender. I put the fender back in place and checked the balance.
View detail
Satisfied with the sense of togetherness
I installed it on my 2021MODEL. It is cheaply made, but I feel no problem to integrate it with Fender.
We have not used it in the rain yet, but we expect it to reduce mud splashing.
View detail
Fits: MV AGUSTA TURISMO VELOCE, MV AGUSTA SUPER VELOCE 800 SERIE ORO, MV AGUSTA SUPER VELOCE 800, MV AGUSTA RUSH 1000, MV AGUSTA F3 RR, MV AGUSTA DRAGSTER 800, MV AGUSTA BRUTALE 800, MV AGUSTA BRUTALE 1000RS, MV AGUSTA BRUTALE 1000 SERIE ORO, MV AGUSTA BRUTALE 1000RR
For F4-BRUTALE1000RR
I bought this to keep it from getting dirty from Fluid, Dust, etc.
Replace the protective seal when it becomes dirty.
View detail