Reviews
FenderExtender on the grom
I purchased these to reduce mud splatter on my Horizontal TypeEngine when I bought my Grom new. I used 3M double-sided tape instead of the supplied double-sided tape for installation. It has been 7 years and 56,000km since I bought it and it has reduced the mud splatter without any deterioration. I thought that the cost performance might not be so good, but I have not had any problems for more than 50,000 km, so I felt again that it is a good product. View detail
Fits: HONDA GROM, HONDA CRF250, HONDA CBR500R, HONDA CBR400R, HONDA CB500F, HONDA CB400F, HONDA CB500X, HONDA 400X
Quantity:1 Set of 2pcs. is a sense of security.
I replaced the PanelProtection film that I had been using for some time because it was scratched. The texture is soft. It was difficult to remove the air from the film. (See picture, a little air bubble was left on the Right Side). However, the kit has two pieces, so even if I fail once, there is another piece, so I don't have to worry. We will try again later. View detail
Recommended for those who ride in the rain, such as commuters.
I think it is effective Large for those who ride to work etc..on rainy days like Title.
I never ran in the rain. (Impact of increased telecommuting) It will be a decision of about 5? on the way back.
I think the effect was to reduce the amount of dirt on the exhaust pipe and cylinder fins.
In my case, it may be a mistake when adjusting to Fender, but it is a little Quantity.:Pair (for Left and Right) Clearance of the "A" was different, but I think it is a resin molding product, so it is totally acceptable.
I used the supplied double-sided tape for 12 hours of crimping and 2 pieces of the supplied Nylon rivet just to be safe.
Double-sided tape is divided into parts, and the instruction manual makes it easy to understand.
I have a Nylon rivet, Φ4Drill to drill the hole, but I think you need to be careful about the position of the hole, the length of the neck and the push of the Rivet is the limit and it was hard to insert. It is recommended to find a good position as thin as possible. I was just eyeballing it, so it was at the limit. Also, Rivet is convenient because it can be inserted with bare hands.
View detail
Perfect fitting, great protection from water and mud splashing around the engine!
I was concerned about the double-sided tape that came with the product, so I used the Scotch vehicle tape I had on hand and installed it on the FFender.
Even if you don't use the supplied Anchor Pin, there is no sign of it coming off.
It's an Exclusive Design and the fit is perfect!
Dramatic reduction of water splashes and mud splashes!
Cleaning the fins of an air-cooled horizontal engine can be troublesome, so this item is a must-have for owners who need to run on wet roads.
View detail
Alright
There is a lot of mud splatter when you use the Fender Eliminator. So I put these on. I posted this about 2 weeks after I put it on and it got rained on during my commute. I also work from home, so I haven't tested it enough, but it's nice.
Installation is very easy. Clean with the included AlcoholSeat
It is glued with Double-sided Tape and left for 12 hours.
I leave it crimped with Shako. After that, I drill the clip of the attachment with M2Drill and melt the reverse side with a lighter to make it difficult to peel off. So far, it has come without a problem. It is convenient if you have the type that does not have a shako in the home center because it is sold for 2~3 hundred yen. The instruction manual is included and it was kind to the beginner.
View detail
Super effective in reducing water splashes and mud splashes on FFenders!
The double-sided tape that comes with the product has a little bit of anxiety about the adhesiveness, so I used 3M's Double-sided Tape for Cars as the main adhesive.
Then, even if you don't put the attached Penetrating Pin for fixing, it can be fixed perfectly, and there is no sign of coming off even if you use it for more than 500km.
Exclusive design and perfect fitting. (I'm not planning on riding this GROM in bad weather though) In the event that you encounter rain with the Ron Two, you can clearly see that the dirt will be drastically reduced.
If you don't want to get your Motorcycle dirty, this is a super Recommendation product.
In addition, although the for rear is also out, I have already taken measures with Universal Product which I bought in Amazon, and because the for rear is a little too expensive, there is no plan of the purchase.
View detail
Extender Fender Installation on 2020 Grom
I installed it on the Grom.
The Size of the extension is also just about right, which is nice.
The reason I wanted to install this is that the NORMAL Fender is short
Even the top side of the cylinder head has mud splatter and is very dirty and difficult to clean!
For installation, remove the Fender and fix with Double-sided Tape and PlasticHook.
You will have to drill the Hook holes yourself.
After installation, there is mud splash on the bottom of cylinder but not on the top of head.
It's gone.
View detail
To prevent mud, stones, etc. from sticking to the Engine
I chose this product because I can't find any other dedicated Mud Guard products to run various places
Installation is easy
The included Double-sided Tape is strong and includes an extra pin for reinforcement but
I didn't want to make a hole in it by reinforcement, so I used Double-sided Tape and I played SiliconCoking
The accuracy of the Gold model is good and Exactly, and I like the functionality without any discomfort after wearing it
Honestly, how is 5,000 yen for this small plastic part? I thought for a bit
View detail
After the rain..
A bit of a problem for GromUser.. "Dirt around the engine head after running in the rain and after rain This symptom is a stipulation of the Horizontal TypeEngine The product that solves such problems is the one I bought this time "Peitzmeier Company:Extender Fender Fender It is
Let's start with the Impression of the product content!
Products include the Handling and Installation Instruction Manual, Extender Fender Fender, and Screw to prevent falling out, AlcoholWipe (degreaser), Double-sided The contents of the tape The unreliable attached Double-sided Tape which was in Impression until now is It has been changed to the strong Double-sided Tape that has been versioned up Probably, when the Extender Fender attachment fails and it peels off.... I'm sure you'll let them, so be careful where you stick them! It is If you fail to do so, I recommend that you warm it up with Dryeretc. and peel it off In that case, do it at your own risk!
Next is an Impression of the Extender Fender installation
I am a "Anti-shell screw In order to use Extender Pre-install the Fender After temporary installation, please add the Quantity:Pair (for Left and Right) In order to decide the position of the screw installation for preventing the screw from falling out of the screw, decide the reference point to OEMFender To install the screw to prevent the screw from falling out, please check the diameter of the head part and make sure that the hole is 4mm We make sure of the positioning If the positioning is done well, it will look like the OEM finish On the other hand, if you fail, the result will be unnatural, so be careful! That's it If you can make it to that point, you need to drill the screw mounting hole for prevention of falling out It is the basis of Drill, but it is not to drill a large hole at once, but to drill a large hole gradually It's all about opening it up! I process the drill with the degree of caution to the extent that I beat a stone bridge and cross it (laughs) After the processing is successfully completed, the OEM Fender and the Extender Fender can be used with the attached degreaser Use to degrease After degreasing, attach the included up-dated double-sided tape to your spec After applying Double-sided Tape, the OEMFender is carefully attached Install the Extender Fender securely (If the position is misaligned, the Double-sided Tape Firmly works I think you will damage the Extender Fender, so if you do so, use Dryeretc I suggest you heat it up and peel it off with a When the Extender Fender is securely attached to the mounting position, you can use the Install the Screw and let it rest for 12 hours I used a Clamp to fix it in place and left it resting!
Now it's time to install Impression on the vehicle
The Extender Fender is also included with the double-sided tape to prevent it from falling off By using Screw, I was able to install it in the OEM Fender after attaching the sided tape, I fixed it with clamps for more than 12 hours and left it to rest I was able to Firmly install it on the OEM Fender Now it's time to install it in the vehicle and it's easy to do with the 10″ tool and the Hexagonal Wrench The OEMFender can be returned After the installation, there is no interference in the Tire of OEM Fender, and there is no interference in other parts I think it is the proof that the shape and details are well made
This is the overall Impression of Extender Fender The making of "OEM? I think that this is the place that makes me think that it is a good product However, if you use only the attached double-sided tape, you will need some additional processing But if you use the screw for prevention of falling off, you need to do some positioning and drilling etc I think it will be a burden for those who are not used to processing The durability and the role of Extender Fender will be felt by using it in the future I think that's part of it, so we'll have to wait and see how you rate this one! Let's just say How is the Cost performance worth the $5400 selling price? If you're saying, "I don't know what to do," then... I'm sure people have different opinions, but if you're saying, "I don't know what to do," then you're wrong Then I think it's a reasonable Gold amount for me
View detail
Extension of mudguard @ GROM
【What made you decide the purchase?】 Because I got cheaper than usual in Campaign.
【How was it actually used?】 Sufficient, functioned as mudguard.
【Was it difficult to install? (Hard parts case)】 I can not use the included Double-sided Tape, attached my own ButylTape and attached it.
【Please tell me the point of installation and hang (in the case of Hard parts)】 Clean the adhesive surface.
[Is there anything I was disappointed about?] A little making is sweet
【Hope for Manufacturer - Please tell me if there are any improvement points】 None
【Have you compared items?】 Required
[Others] Any
View detail
Water countermeasures
As it is NORMAL, there are quite a few of the water splashes, so I bought it as a countermeasure.
Kit was attached with Puri Rivet and Double-sided Tape, but it is fixed with Epoxy adhesive and Aluminum Rivets because it is prevented from dropping out.
The water splash that had been flying to near the Top Bridge was considerably reduced.
View detail
It is expensive but I can be convinced
Subtlely do not match Normal fender. I am worried about the included Double-sided Tape, so I embellished with Emon's Super Strong Double-sided Tape, but I have a slightly floating place. Drilling is necessary to use the included Plastic Pin. I feel that texture is good, I think that there is no thing to remove if attached I think that it is good to fix with Double-sided Tape and Bond.
View detail