Reviews
Fits: BMW RnineT, BMW RnineT, BMW RnineT /5, BMW RnineT Pure, BMW RnineT Scrambler, BMW RnineT Urban G/S
Satisfied
Purchased to prevent dirt inside Fender
I think it works personally.
View detail
In Mudguard.
Radiator guard is now less dirty.
Installation at a store is recommended.
View detail
This is a must have for Rebel 1100
I installed it on the Red one's body and it does not feel uncomfortable.
The REBEL 1100 is miserable around the Radiator when running in the rain or on watery areas.
I wanted to have a Long fender instead of Short as an OEMOption, but this product replaced it.
I was satisfied because it was easier to clean after driving and it didn't look bad.
Installation is also easy with double-sided tape.
As a precaution, it would be better to treat the joints inside the Fender with GORILLATape, etc. to prevent them from falling out.
View detail
As Radiator cover
I purchased this product to avoid dirt and foreign objects in Radiator!
The installation was done at the store.
He did it for several thousand yen.
It was quite a good purchase!
View detail
Fits: YAMAHA Tracer 9, YAMAHA Tracer 9 GT, YAMAHA XSR900
I am mostly satisfied!
It looked like I needed to drill holes to install it, so I asked the YSP store to do it for me.
Before installation, small stones (1-5mm) accumulated in the Swing Arm, but after installation, they hardly accumulated at all.
It has been installed for about half a month, so I don't know about durability.
View detail
Fitting is perfect.
Purchased because the Rear suspension gets very dirty when driving on wet roads.
Instruction Manual was easy to understand with translation (please type here).
I think Right Side is impossible without removing Silencer.
The fitting is perfect, and it is covered to the rear suspension area.
Very satisfied with the drastic reduction of dirt on wet roads.
View detail
Fits: SUZUKI GSX-S 1000 GT, SUZUKI GSX-S 1000 FA, SUZUKI GSX-S 1000, SUZUKI GSX-S 1000 GX
Without it, water will splash on your back.
It was installed on a 2017 GSX-S1000.
When installing the product, remove the Axle Shaft and reverse the Nut side. Also, the rear axle block on the product installation side is no longer necessary.
If you are not confident about doing the installation yourself, it is better to have a Motorcycle shop do it for you.
The Fender Eliminator causes a lot of splashing, but I am satisfied that this product eliminates a lot of the splashing.
Visual also differentiated itself from the others and made Parenthesis look good.
View detail
The effect is Large-Thick, though not noticeable Custom.
As shown in the image, extend Rebel's shorter FFender by 14 cm.
It fits just right in terms of shape, not so much that it disrupts the original design.
If you are not an owner of REBEL, you may not even notice that it is installed.
A fixed pin is included in the package, but I am not confident enough to drill a hole in the Fender.
Double-sided tape is the only fixation.
This will reduce mud splash etc. to the Radiator area to Large width, which will also make maintenance easier.
View detail
Fender removal was requested by DREAM.
The description here says it is easy, double-sided tape only, but it also says that if it has Small cherry biz, it needs to be fixed. When I bought it, it was attached beautifully, so I was not sure what to do with it, but I wanted to install it neatly, so I tried to find a way to remove Fender, but this was quite Large strange. So I took it to DREAM and had them remove it and put it back on again. The price was only a few thousand yen.
I degreased the surface, installed it with double-sided tape, cured it with masking tape, and then decided where to drill the holes. I think it is better to drill the holes inside the corners of the fender to prevent cracking and bending.
The effect is outstanding. I know a lot of people get their Radiator dirty from mud bouncing off even the slightest puddle, but with this on, it doesn't get dirty at all!
View detail
I was able to fit it without that much discomfort.Large sturdy, even for a 2017 model.
The color of the Fender is matte black, so I was able to install it without much discomfort. I worked with the Fender installed on the side, but it is easier to work with the Fender removed. If you want to use the fixed pin, you need to drill a 4mm hole so that you don't accidentally stick the tire in. I haven't done any real wet weather driving, but the Fender is extended and seems to work well. It was installed on a 2017 RC90, although it is not correct in terms of fitment. I bought mine because this one had a faster delivery time, but only at my own risk. 4 Pins were included, but I'm using 2 for now and seeing how it goes. View detail
I was able to do this without removing the Fender
Front Fender cannot be easily removed.
Therefore, it was necessary to devise a way to keep the Drill tip from hitting the Tire when Drilling and to keep the Extender in close contact with the Fender.
From both SIDE of the Fender, a thin chi board was inserted to protect the Tire and to compress the Ex-Kender.
It is a good idea to use masking tape during drilling to avoid scratching the Fender.
Fender is quite stiff.
View detail
Recommended for those who ride in the rain, such as commuters.
I think it is effective Large for those who ride to work etc..on rainy days like Title.
I never ran in the rain. (Impact of increased telecommuting) It will be a decision of about 5? on the way back.
I think the effect was to reduce the amount of dirt on the exhaust pipe and cylinder fins.
In my case, it may be a mistake when adjusting to Fender, but it is a little Quantity.:Pair (for Left and Right) Clearance of the "A" was different, but I think it is a resin molding product, so it is totally acceptable.
I used the supplied double-sided tape for 12 hours of crimping and 2 pieces of the supplied Nylon rivet just to be safe.
Double-sided tape is divided into parts, and the instruction manual makes it easy to understand.
I have a Nylon rivet, Φ4Drill to drill the hole, but I think you need to be careful about the position of the hole, the length of the neck and the push of the Rivet is the limit and it was hard to insert. It is recommended to find a good position as thin as possible. I was just eyeballing it, so it was at the limit. Also, Rivet is convenient because it can be inserted with bare hands.
View detail
Perfect fitting, great protection from water and mud splashing around the engine!
I was concerned about the double-sided tape that came with the product, so I used the Scotch vehicle tape I had on hand and installed it on the FFender.
Even if you don't use the supplied Anchor Pin, there is no sign of it coming off.
It's an Exclusive Design and the fit is perfect!
Dramatic reduction of water splashes and mud splashes!
Cleaning the fins of an air-cooled horizontal engine can be troublesome, so this item is a must-have for owners who need to run on wet roads.
View detail
Alright
There is a lot of mud splatter when you use the Fender Eliminator. So I put these on. I posted this about 2 weeks after I put it on and it got rained on during my commute. I also work from home, so I haven't tested it enough, but it's nice.
Installation is very easy. Clean with the included AlcoholSeat
It is glued with Double-sided Tape and left for 12 hours.
I leave it crimped with Shako. After that, I drill the clip of the attachment with M2Drill and melt the reverse side with a lighter to make it difficult to peel off. So far, it has come without a problem. It is convenient if you have the type that does not have a shako in the home center because it is sold for 2~3 hundred yen. The instruction manual is included and it was kind to the beginner.
View detail
Super effective in reducing water splashes and mud splashes on FFenders!
The double-sided tape that comes with the product has a little bit of anxiety about the adhesiveness, so I used 3M's Double-sided Tape for Cars as the main adhesive.
Then, even if you don't put the attached Penetrating Pin for fixing, it can be fixed perfectly, and there is no sign of coming off even if you use it for more than 500km.
Exclusive design and perfect fitting. (I'm not planning on riding this GROM in bad weather though) In the event that you encounter rain with the Ron Two, you can clearly see that the dirt will be drastically reduced.
If you don't want to get your Motorcycle dirty, this is a super Recommendation product.
In addition, although the for rear is also out, I have already taken measures with Universal Product which I bought in Amazon, and because the for rear is a little too expensive, there is no plan of the purchase.
View detail
Clearly effective, 120 points of satisfaction
The design and quality of this product is perfect. The front fender is too short to begin with. View detail
I want to start with a new car.
Front fenders tend to be shorter these days, and although parenthesis is good, there are more water splashes and small stone ricochets, and more scratches and dirt on the engine, exhaust pipe, and radiator. This is especially recommended to those who are worried about such things. I started using it on my last car and it was very effective and I put it on the car I replaced right away. I do not want to go touring without it. Installation is a bit of a hassle but I would recommend removing the Fender as it is easy to position and prep. I installed it without removing it. I installed it with just the double-sided tape that came with it and checked it when I washed the car. The quality of the texture is good, but the surface is still plastic, so you may want to blow it clear or something else if you like. The shape of this product is for car models only.
It came on nicely, Cost performance was subtle before I used it, but now I think it's very high.
View detail
To prevent mud, stones, etc. from sticking to the Engine
I chose this product because I can't find any other dedicated Mud Guard products to run various places
Installation is easy
The included Double-sided Tape is strong and includes an extra pin for reinforcement but
I didn't want to make a hole in it by reinforcement, so I used Double-sided Tape and I played SiliconCoking
The accuracy of the Gold model is good and Exactly, and I like the functionality without any discomfort after wearing it
Honestly, how is 5,000 yen for this small plastic part? I thought for a bit
View detail
After the rain..
A bit of a problem for GromUser.. "Dirt around the engine head after running in the rain and after rain This symptom is a stipulation of the Horizontal TypeEngine The product that solves such problems is the one I bought this time "Peitzmeier Company:Extender Fender Fender It is
Let's start with the Impression of the product content!
Products include the Handling and Installation Instruction Manual, Extender Fender Fender, and Screw to prevent falling out, AlcoholWipe (degreaser), Double-sided The contents of the tape The unreliable attached Double-sided Tape which was in Impression until now is It has been changed to the strong Double-sided Tape that has been versioned up Probably, when the Extender Fender attachment fails and it peels off.... I'm sure you'll let them, so be careful where you stick them! It is If you fail to do so, I recommend that you warm it up with Dryeretc. and peel it off In that case, do it at your own risk!
Next is an Impression of the Extender Fender installation
I am a "Anti-shell screw In order to use Extender Pre-install the Fender After temporary installation, please add the Quantity:Pair (for Left and Right) In order to decide the position of the screw installation for preventing the screw from falling out of the screw, decide the reference point to OEMFender To install the screw to prevent the screw from falling out, please check the diameter of the head part and make sure that the hole is 4mm We make sure of the positioning If the positioning is done well, it will look like the OEM finish On the other hand, if you fail, the result will be unnatural, so be careful! That's it If you can make it to that point, you need to drill the screw mounting hole for prevention of falling out It is the basis of Drill, but it is not to drill a large hole at once, but to drill a large hole gradually It's all about opening it up! I process the drill with the degree of caution to the extent that I beat a stone bridge and cross it (laughs) After the processing is successfully completed, the OEM Fender and the Extender Fender can be used with the attached degreaser Use to degrease After degreasing, attach the included up-dated double-sided tape to your spec After applying Double-sided Tape, the OEMFender is carefully attached Install the Extender Fender securely (If the position is misaligned, the Double-sided Tape Firmly works I think you will damage the Extender Fender, so if you do so, use Dryeretc I suggest you heat it up and peel it off with a When the Extender Fender is securely attached to the mounting position, you can use the Install the Screw and let it rest for 12 hours I used a Clamp to fix it in place and left it resting!
Now it's time to install Impression on the vehicle
The Extender Fender is also included with the double-sided tape to prevent it from falling off By using Screw, I was able to install it in the OEM Fender after attaching the sided tape, I fixed it with clamps for more than 12 hours and left it to rest I was able to Firmly install it on the OEM Fender Now it's time to install it in the vehicle and it's easy to do with the 10″ tool and the Hexagonal Wrench The OEMFender can be returned After the installation, there is no interference in the Tire of OEM Fender, and there is no interference in other parts I think it is the proof that the shape and details are well made
This is the overall Impression of Extender Fender The making of "OEM? I think that this is the place that makes me think that it is a good product However, if you use only the attached double-sided tape, you will need some additional processing But if you use the screw for prevention of falling off, you need to do some positioning and drilling etc I think it will be a burden for those who are not used to processing The durability and the role of Extender Fender will be felt by using it in the future I think that's part of it, so we'll have to wait and see how you rate this one! Let's just say How is the Cost performance worth the $5400 selling price? If you're saying, "I don't know what to do," then... I'm sure people have different opinions, but if you're saying, "I don't know what to do," then you're wrong Then I think it's a reasonable Gold amount for me
View detail
Fits: DUCATI Multistrada 950, DUCATI Multistrada Enduro, DUCATI Multistrada 1260
Design like OEM Product
I found this item where I was concerned because the Radiator is hit by mud
Since this Fender is divided into two, this Motorcycle removes only the back part, opens a hole of 3 mm with Double-sided Tape and fastened with the attached Pin. It looks as though it looks good from the beginning, it does not feel uncomfortable.
View detail