Reviews
Fits: Others , Others , Others , Others , Others , Others , Others , Others , Others
Available for frando 7nb
Let's try to change frando 7nb to MechanicalSwitch View detail
Fits: Others , Others , Others , Others , Others , Others , Others , Others , Others
Used for frando 7nb
We used the same shape as brembo for frando 7nb.
The following three products, including this product, can be used for MechanicalSwitch conversion.
We chose Gold for the Accent this time, but Black products are also available.
https://www.webike.net/sd/21995643/
Ladybird Ladybird:LBP-BS1000
Mechanical Type Brake Switch
https://www.webike.net/sd/21216231/
KOHKEN KOHKEN:KOK-2031TI
Push Rod Pivot Brembo Radial Master
https://www.webike.net/sd/21216233/
KOHKEN KOHKEN:KOK-2030TI
Lever Pivot Brembo Radial Master
View detail
Lever Replacement
Brake lever, I have been wanting to replace it for a while and was curious to buy this one.
After much deliberation over whether to go for the short or middle type, I decided to go for the middle type, which was in stock.
Looks and uses don't seem to be too bad.
View detail
Not much change.
Maybe it's not necessary at this price? View detail
Short may be too short?
Only the movable part of the lever was replaced because I didn't like the thick feeling peculiar to bremboLever.
I selected Short, but it is much shorter. It's just enough to get your middle finger over the end, index and middle finger Quantities.:It is just about right for 2pcs. Personally, I thought it was too short, so I will buy a Middle.
View detail
Brake master lever replacement
The CORSA Corta Lever is slim and I felt uncomfortable from the thicker Lever I had been used to, so I replaced it with Koken's AeroLever.
Basically the finger Quantity:Since it is a 2pc hang, I selected the Short lever which is available in stock.
However, the grip was as expected, but it was too warped compared to the OEM Lever, or maybe it is because we have small hands, or maybe the Lever was too far away and we failed even though we set it at the front of the Lever adjustment range of the CORSA Corta….
At any rate, I managed to get to the acceptable Limit position by changing the CORSA Corta Lever play from NORMAL to SPORTS.
Normally, I would prefer the RACING position, which is much closer, but since it is play 0, I thought I would get used to the Sports Response for a while, and if it feels uncomfortable, I would try the RACING position.
I often put my finger on the tip of the lever, but is the base of the lever (closest part) correct? (Is it correct to put your finger on the base of the lever (the part closest to the base of the lever)? If you put your finger near the tip of the lever, the lever may be too far away.
View detail
for Racing CaliperPad spring
By installing on a 4POT 40mmRacing caliper that is not equipped with a pad spring, it reduces the annoying pusher-pusher sound caused by pad play during BrakeFree. I bought it to try it out, since it is described and seems to have a good reputation.
The color is beautiful when new. I am looking forward to the change after installation.
Selling price, it would be helpful if it were a little cheaper.
View detail
Watch the direction of travel
The Brake Pads are very noisy, so I installed the Brake Pads. (The one that is wide horizontally) It should be correct to attach the letters Eva TEC as they come. View detail
PetitCustom
Bleeder Cap is usually used for Material:The rubber cover is available in anodized color, and the aluminum cover provides an enhanced texture.
We chose the color Black because we prefer the OEM look.
View detail
For bremboOEMHose
[How is it used?
Brembo master is installed on MainMotorcycle's XJR1300C and Racer's YZF-R25 MASTER.
Oil hose from bremboOEM is 9.5Φ Clip that comes with brembo tank kit is not so good......................................
I was looking for a good hose clamp and found this product.
So far, the Fluid leakage and other problems have been completely solid, so I can safely recommend it.
Was the one you received as per Image?
The surface finish is even better than Image's! The price is cheap and the two-pack is easy to use.
Was the installation difficult?
It's not hard to do
Even if you want to replace only the clips, you have to disconnect the oil hose once.
I think it is better to do it with Timing to remove Brake fluid such as Fluid replacement.
How was your experience with it?
In a good way, it is insanely hard. It's tough to spread Clamp with bare hands.
It should be properly pinched and spread with radio pliers, but it is better to apply Dustcloth or something else before applying the tool because it is easy to scratch it.
Also, it is quite tight when passing through the Nipple section. If you try to pry too hard, you may damage the Nipple side.
After moistening the brake hose with Parts Cleaner or similar, slide it into the brake hose.
It can be installed without giving Stress to the surrounding Parts.
[Included Parts:were they on?
As shown in the picture, ClampQuantity:2pc. Nothing but Set.
[Was there anything that disappointed you?
Nothing in particular. If I had to say, I'd say it's too hard and could be softened a bit.
I think the knob could be made a little bit larger to make it even easier to use.
View detail
Stopped!
I have been suffering from oil seepage from the bleeder bolt (bremboOEM) on my bremboRCSMASTER for 6 years and replaced it with a new OEM bleeder bolt. It has been a week since I installed this product and the leakage has completely stopped! 。 If you are suffering from oil seepage, it is worth a try. Tightening torque should be less than 20Nm. View detail
Third generation RepairSwitch
This is the third RepairSwitch.
Wiring breaks from the root in approximately 3-year cycles.
The switch itself is fine, but the inside of the base itself is thin and fragile due to its small size, the switch body is fixed and the harness on the body side is free, but over the years vibration and other factors have caused the stress to build up and cause a pop-drill.
It can also be folded without leaks even when secured with Tie Wrap.
I was getting tired of all this, so I solidified the Body and Wiring with a GRU-Gun and shrink tubing.
In the meantime, I have been using only the GRU-Gun to connect and heal the last broken Switch with the Solder, and it is looking good.
View detail
If you use Brembo master with electronic ThrottleMODEL, replacement is recommended.
[How is it used?
When we replaced the brembo radial master cylinder on the StreetTripleRS, there was a problem with the lever interfering with the throttle holder due to the thickness of the switch box and throttle holder.
The AeroLever from Kohken was replaced not only to reduce air pressure pushing in the lever by cutting out the wall, but also to prevent interference with the throttle holder since the shape around the throttle holder is slimmer than that of the brembo lever. The new lever is a very good solution for the problem of the throttle holder.
Was the one you received as per Image?
When stacked with the brembo lever, the shape around the throttle holder is indeed thinner, which seems to reduce interference when gripping.
Since there was no Large change in the shape of the fingers, there was no discomfort in the fingering after the replacement.
Was the installation difficult?
Since only the movable part of the Lever is replaced, it can be replaced by removing and replacing the Bolt1 pc.
How was your experience with it?
I have not yet tested it with the actual lever coming in at Circuit, but from the feel of holding it, there is definitely more clearance with the Throttle holder than there was before the replacement.
If this does not seem to work, the only way is to add a Remote adjuster or something to be able to adjust it while driving.
[Included Parts:were they on?
Since only the retractable portion of the Lever is available, it cannot be replaced without the Retractable Lever.
[Was there anything that disappointed you?
As mentioned above, since there is only a movable portion of the Lever, the price seems expensive when considered on its own.
However, we are willing to split the cost if it will improve the usability of Brake more than that.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Fits: Others
brembo
This is installed along with the change to brembo brakes.
Since the installation as it is causes interference, we managed to avoid the interference by adding a few offset parts.
Quantity:Set, I wish it were cheaper.
View detail
brembo installation
We installed this bracket along with the brembo bracket. The shape of the bracket looks good and I like it, but I had a little trouble installing it as it is with the separate handle and cowl because it interferes with the bracket.
It would be helpful if the selling price were a little lower.
View detail
Small personality, durability is …
I found it to be a very good product for One Point Fashion for my feet.
The work itself only requires replacing the Breeder's Cap, so even beginners can do it quickly and easily.
The texture of Anodized was good and I thought it was indeed a Kohken product.
But it's not very durable;
After six months, the Rubber cracked, and after about seven months, only the Aluminum Cap was missing.
It may be inevitable for the structure to fly away, but the caliper generates heat, and I would like to see the use of heat-resistant and durable rubber.
We wanted to take a look at the NORMAL Rubber cap, so we gave it a slightly lower score.
View detail
Fits: Others RCSClutch master cylinder
Note that Wiring is weak.
The size is very small, but the wiring is very weak. I wish the wiring part could be reinforced with a plate or something. View detail
Repair Parts
Tie Wrap together the Wiring from Switch and it will break in the near future.
The original Switch was just discarded in anger.
This Repair Parts did not include Bolt, as expected, but Bullet Terminal was included, thank goodness!
I headed to my neighborhood Home center to buy Bolt!
Size is 2mm and I bought the length 10mm.
Washer and Nut also Quantities:Set and it is 5Quantity:It contains about a set and costs 200 yen. I don't think I will be using it in the future, but I put it away in the "Large" case.
What I'm trying to say is don't throw Bolt away!
View detail
SECTION
For those with ABS, Bracket's Seisa k is required.
There is also a part number for Bracket with Bracket, but it's not sold...
View detail
With the brembo replacement
With the new brembo brakes, the tank was also changed and this bracket was installed to hold the tank in place.
Because it interferes with the Upper Cowl Bracket, I was able to install it without interfering somehow by fixing the parts which shifted 20mm.
I changed the fixed bolt to black because of the black color.
It looks good, but it can't be installed as is, and the price is reasonable.
View detail