Reviews
![[DAYTONA x AC SANCTUARY] RCM Concept COZY Seat [COMP]](https://img.webike-cdn.net/catalogue/images/101907/24329_TS.jpg)
Fits: KAWASAKI Z900RS SE, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS
A little disappointed.
The design is great, but long touring is a pain in the butt for me personally.
As a result, I purchased DAYTONA's Gay Lupinz.
View detail
Crafting accuracy is not so good
There is a cut-out Sugar Crystal step near the shaft center.
This made me wonder if Large is sturdy enough.
Unlike Front, Rear is honestly not as effective.
I don't know. For this Gold amount, I should have gone with the KMT product for $57,000.
View detail
![[Mr Quick][Color] Clear Cylinder Head side cover](https://img.webike-cdn.net/catalogue/images/132620/mr19-cc18-sv_TS.jpg)
Fits: HONDA CROSSCUB110, HONDA MONKEY125, HONDA CT125, HONDA DAX125, HONDA GROM
Oil leak
I ran around the neighborhood and after one night it leaks oil. View detail
Logo will soon become Brown.
I used it for upright Fork.
I have no complaints about the product itself, such as the Tie WrapGap prevention, easy installation without removing the Tire, etc., but the Logo turns Brown quickly.
Other than that, I really have no complaints, it's just too bad.
View detail
Fits: KAWASAKI Ninja ZX-25R
The sound is good, but … the quality is disappointing.
The volume is a little louder than OEM, and when idling, it has a nice bass sound.
The running sound is more outgoing than OEM.
However, long-time operation can cause sound fatigue.
Since it is a slip-on silencer, I can't feel the increase in power or anything like that, but I think I'm satisfied with it for the enjoyment of its appearance and sound.
I like the product, but there were many scratches and scuffs on the carbon part of the silencer end, which made me feel the quality control was low.
I have bought several YOSHIMURA Exhaust Systems in the past, but this is the first time I have ever seen something like this, which is a shame because they are expensive Parts.
View detail
Fits: HONDA Giorno2, HONDA Byte, HONDA CREA SCOOPY, HONDA GIORNO CREA, HONDA SMART DIO-DX, HONDA SMART DIO
Boss does not fit in Pulley.
The clarity of the bushings on the pulley was not quite right and the OEM bosses would not fit. Is there a difference in the product, or is it an individual difference in the Both Sides of the car? (・・;)
I managed to insert and install the bushing after grinding it with PaperFile, but it is not as smooth as the OEMPulleyOEM boss combination, so it is a bit of a bummer.
View detail
Fits: KAWASAKI ELIMINATOR, KAWASAKI ELIMINATOR SE
the same as it was reputed to be
As per other reviewers, it's still difficult to put it up.
The Exclusive Design and Just Size are not tolerant of mistakes, and even if the center part of the main body can be managed, it is very difficult to put the thin and round surrounding parts in the right position.
Seat was thin and stretched when working with it... I was out of my depth.
View detail
。
the four arithmetical operations (addition, subtraction, multiplication, division) View detail
Too much shaking bothers me.
The Fender Eliminator is also long, so it swings vertically over bumps and other obstacles.
All those who have seen it for the first time say they are worried about the sturdiness of Large's installation if they look at it from the back.
A friend of mine who bought the same one said he got tired of it and decided to go with a different Manufacturer.
To be honest, I don't really recommend it.
View detail
Fits: Others
For charging smartphones
I put it in for powering my smartphone and a separate ETC. Maybe it is because my motorcycle is old, but DAYTONA products always give me a hard time. View detail
Fits: HONDA APE, HONDA BENLY50, HONDA DAX, HONDA MONKEY, HONDA CT110 HUNTER CUB, HONDA GB250 CLUBMAN, HONDA FTR223, HONDA CL400, HONDA FTR220, YAMAHA SRV250, YAMAHA RENAISSA, YAMAHA BRONCO, YAMAHA TW225, YAMAHA TW200, YAMAHA SR400, YAMAHA SR500, SUZUKI VANVAN, SUZUKI GN125, SUZUKI GS125, SUZUKI VOLTY
Not very good
The paint on some of these has a bumpy texture, like the units weren't clean when the paint was applied. One of them had an electrical short upon installation which was popping my signal fuse. Luckily I had bought a spare. Installaton wasn't a big problem, but I wish they used thicker gauge of wire, it's very thin. Very inexpensive blinkers, but you get what you pay for. I wish I had spent a little more and gotten better quality blinkers. View detail
![[Repair Parts] Camshaft Chain Tensioner Bush Rod Head](https://img.webike-cdn.net/catalogue/images/15887/00-01-0279_01_TS.jpg)
Like it's no different than OEM Product?
I've compared it to the OEM and it looks identical... View detail
It was used as a replacement from OEM.
I have no complaints with the OEM BURGMAN 200, but when I installed the support plate for the Gold attribute of the Brake Pads, I felt the brake dragging at first, and I was concerned, so I contacted the manufacturer. The answer was that they could not say that it is OK to install without using OEM parts. It gets better after a little driving, but at first I was a little worried because the Rear tire did not rotate when idling.
This is the second time I have purchased this product, but I feel it is not as durable as the OEM because the pad has almost no remaining pad after 6,000 km since the last time I replaced it.
I think DAYTONA's RedPad is more durable and Control is better. I think I will probably not use it for the third time.
View detail
The durability of Band's Rubber is poor
After 2 months, the band's rubber corroded and snapped off as shown in the picture.
I had no choice but to fasten it with coated needle gold.
View detail
Fits: YAMAHA SR400, YAMAHA SR500
Freak’s PIT:Freak's Pit OriginalMeter Bracket Extra Thick
[How is it used?
I purchased the OEM Meter Bracket because I was concerned about the height when using the separate handle.
Was the one you received as per Image?
Yes.
Was the installation difficult?
The installation itself was not difficult.
How was your experience with it?
The meter was lowered, which made it look cool when the bike is mounted on the motorcycle or when viewed from the side!
[Included Parts:were they on?
A simple Instruction Manual is included, but the WhiteBlack color makes it rather difficult to read and does not provide detailed installation instructions.
[Was there anything that disappointed you?
Vibrations cause the Meter to turn round and round. (Gap.) This is the point where it ends up.
I put a transparent seal on the invisible position to prevent it from turning.
View detail
Fits: HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB 50Custom, HONDA SUPER CUB 50Custom, HONDA SUPER CUB70, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA SUPER CUB 90, HONDA CUB press 50, HONDA LITTLE CUB, HONDA CUB press 50, HONDA LITTLE CUB
Difficulty in weather resistance
Why is it that everyone is so quick to exchange to NORMAL? I was wondering,
Now I know why. After about a year of storage under the eaves, the surface hardens.
ParisParis and tear it up.
View detail
![[KAISOKU] Outerwear Clutch](https://img.webike-cdn.net/catalogue/images/86178/02152103_602a630a6f189_TS.jpg)
Fits: YAMAHA BW'S100, YAMAHA JOG, YAMAHA JOG-Z, YAMAHA GRAND AXIS 100, YAMAHA JOG50, YAMAHA JOG-EX, YAMAHA AXIS90, YAMAHA AXIS90 Profoot, YAMAHA AXIS Pro Foot, YAMAHA JOG90, YAMAHA Super JOGZ, YAMAHA AXIS90, YAMAHA AXIS90 Pro Foot, YAMAHA AXISPro Foot, YAMAHA JOG90, YAMAHA SUPER JOG
The weight of the description does not Ate.
OEM 3-type for horizontal JOG (480g) I bought it for the weight Up rather than the
The description gives a weight of 515g, but the actual measurement is only 496g.
OEMs usually increase or decrease by about 5g because of balance shaving, etc,
I could not think of writing an imprementation that I would recommend to others if the Cut-out Outer had an error of almost 20g!
[Regarding installation].
50cc horizontal JOG (3KJ/5AUCase before regulation, 5BM/5SUCase after regulation)
Case cover Gasket is required.
However, the shaft part is thicker than OEM, so when you stop the Nut, insert the O-ring, and try to close the Cover.
The gap with Bearing on the Cover will be insufficient.
So we need to take measures such as thinning the O-ring
・3WF
There's plenty of room to spare. o-ring should be as thin as the 50 story?
You can replace the Nut that stops the Outer with a thin Nut for 50cc
View detail
Not good
It might be a little hard to see and I don't like it. View detail
For Silencer protection
I have always enjoyed forest road touring with gasgas EC250 as a hobby.
It is an application that sometimes runs a little HARD.
This time I bought it with the earnest desire not to add any more scratches to Silencer.
Installation is done by pulling as hard as you can on the Rubber loop.
It requires quite a few parents.
It is cool as a Design, and it Guard Silencer well as a Protector.
I was a little disappointed that it slides and moves when the light is actually turned on, and at first I was concerned about it and had to change the position of the outlet of the exhaust system every time. Recently, I have come to think that it is fine as long as it is on, and I use it as it is without fixing it.
I think it is difficult to increase the number of scratches on the Exhaust System.
I want to remove it when I get good at it.
View detail
I failed.
When replacing the master cylinder, the stock switch box would give me more room for the gas pedal wire.
I bought it The wire is 800mm, and the inner pipe is 44mm without thinking.
This is the source of the mistake. There's no point in making it so high throttle in the first place.
I put it on and it's really high throttle, sweaty, and the gas pedal is really heavy. ・・・・
The wire also seemed a little long ・・・・
I think the balance with Rajpon is great, but maybe this time I made a mistake in choosing the right parts.
It's not an improvement, it's a deterioration.
I'd like to try it next time with a 35mm throttle and 700mm wire.
View detail