Reviews
RepairKit with air leak prevention fluid.
I need this for Air Leak Repair for Repair because the Tubeless process of FRWheel is very Large and strange when I work on it by myself. If possible, I would like you to add air leak Repair fluid as well. The extra Tape was useful for preventing scratches on Frames, Guards, etc. View detail
Fits: その他
Currently being used for Lever Guard of another company.
The bar end fixation attached to another company's Universal Lever Guard was too loose, so we diverted this product to fit the handlebar inner diameter.
I appreciated the fact that the Bar End I.D. had an Exactly component.
View detail
SMCR
To be honest, it may be effective, but I did not feel it as much as I would have liked.
When attached to the current SMCR, it slightly hits the Blinker.
In my case, I put a Washer over the bottom of the Meter installation.
View detail
one...
Heavy than expected to increase the rigidity of quality and texture information There is a feeling that the reaction is clear when using it Installation must be completed after installation on one side There could be an unexpected situation The price is higher than the list price of the web bike. Webbikes ignore the price even if the product shows the price Webike packaging is always good. Delivery and packaging will arrive in a week -_- I'm a little angry. I don't understand why you bought it ¥2,000 more expensive than the price you bought when it was sold out. I think the price went down after the accident. I think I ordered it and put it in stock View detail
Fits: HONDA , HONDA CB750FOUR, HONDA CB750K, KAWASAKI , KAWASAKI 250TR, KAWASAKI KZ650, KAWASAKI W1, KAWASAKI Z-1, KAWASAKI Z-2, SUZUKI GT750, YAMAHA BRONCO
Purchased for CB750four
Purchased both Front and Rear.
I started with the rear tire first and followed the instructions to install it without any problems.
A year later, I installed it in conjunction with the replacement of the front tire, but the joint between the rim and the double-sided tape was not properly connected.
It did not work and I gave up on this one. Maybe a year has passed and the adhesive strength of Tape has weakened.
You may
I couldn't see any difference in the ride quality after installing the Tubeless.
The cost is not so good, because it is more expensive for the
The satisfaction is the DIY sense of accomplishment and the relief when the Tire is inflated and there are no leaks.
View detail
Grom Stabilizer
I can't go so far as to experience an increase in rigidity, but I am satisfied. View detail
Front For anti-rattling
You guys talk a lot about rear shocks.
The front of the Grom... Doesn't it have a really crunchy feel to it?
I bought it hoping it would help.
It's not like I'm an aggressive runner.
After you put it on... Well, it's a little better.
I suppose it depends on how you run.
I'd have to change the fork oil and the springs to get to the root of the problem. And the springs need to be changed.
Doesn't it feel right?
The product itself is well made, and the fork synthesis is a product that can be improved.
think
View detail
DIDfor RaceWheel rim, machining is extremely difficult.
I tried to do Tubeless processing on a TDRRacing wheel for MOTARD by myself. As a result, I had to repeatedly remove and install the tire 4 times for air leak repair. (T ^ T) I know this, but the FR rim is deeper than I expected. I knew this, but the Rim of FR is deeper than expected and I can't cover the wall side well with Tape. I thought I had bought a special one, but it was a little narrower than I expected. View detail
It was a very good purchase.
Before the Air funnel was installed, I was riding with the intake Duct off in the Air Filter Box.
The air filter is NORMAL.
The way the Engine RPM goes up when running without the intake duct and with the air funnel installed (Vaulting, etc.) I thought something had changed.
View detail
If you want to install it for looks, it's a good idea.
I expected the Handling to change, but it wasn't enough to make me feel it.
Attacking Corner may be enough of an effect to make you feel it, though.
The product itself has Impact, so if you're looking for a good look, this might be a good choice.
View detail
Fits: APRILIA SXV450, APRILIA SXV550, BMW F800GS, DUCATI scrambler, DUCATI sports classic, DUCATI Pole Smart, HARLEY-DAVIDSON FLSTSB Crossbones, KTM , SUZUKI , SUZUKI DR-Z400SM, その他 , その他 , その他 , その他 Performance Machine Performance Machine
Simple and easy
I bought it together with Zeta's MOTARDWheel when I bought it.
It was the first time I had to do it myself, so I was worried that I would fail at first.
And it didn't work out in the middle of the process, and I was half-heartedly enforcing it at random.
When I was done, I left the bread pan with a lot of air and it was done without any problems.
View detail
Fits: HONDA glom, HONDA MONKEY125
Short lever assumption
This is the fourth of OUTEX's Items, which are difficult to evaluate on ManiacBrand! It is Until now, the Adjustable Footpeg, Stem Stabilizer, and I added RACINGFunnel The first two are ◎ and Funnel is × And this time, I think it's about zero
As usual, the product arrived in an extremely simple, unimpressive package, and the only thing you need is a It's in there properly Hopefully, I'll still be able to see the Manual easily It is a little clearer picture because it is written about "How to do Setting" or Maniac things and make the letters LARGE (old people can't read it!) I wish I had one I'm sure it will soon become a piece of paper
It's also a bundle of know-how; the Bar End decorations come from a variety of sources But this is not the same as the Bar End and the Hand guard as a protector, or the The function of reducing the vibration of the Handlebar & times;3, which is typical of OUTEX's products It is So I didn't hesitate to go with this one It's not a decoration, it's a function!
When you install it, there are too many Parts like Washer and Collar that stop in the coax To make sure you don't get into trouble, you have to put them through the Bolt in order beforehand so that they don't fall out of the Rubber Band There is That's kind However, remove that Rubber Band and check the order and Bar End and Hand The guardBody is passed through and then it is installed in the Handlebar Because it is a single Screw stopper, the angle of rotation should be adjusted accordingly It is relatively easy to install
So, I'd say this was a poor assumption on our part, but the opening of the Hand guard If you don't use short lever, you can't put it inside the hand guard because it is not so large Lever does not fit We have a splendid (very good operation feeling) touring type of Mr. U-KANAYA Since it is changed to Lever, it interferes perfectly Therefore, I have no choice but to off-set it so that the Hand guard comes under Lever as shown in the picture There was no Parenthesis bad But, well, in case of contact or falling down, it reduces the Risk that Lever breaks to some extent will do
And the key is vibration absorption The effect is there! Originally, the groms don't vibrate in the Handlebar as much (rather, they vibrate in the footpeg) So I didn't hate it so much, but it obviously reduced the vibration It hasn't disappeared Perhaps, depending on the settings (there are additional weights and such), you can make the vibration more Maybe you can turn it off I used to drive a KTM 640SMC (before it became a 690), but that LC4 Engine has a pretty excruciating vibration in the Handlebar The effect of adding this Vibration Absorption Lever Guard to SMC In the video, you can see that the vibration is reduced to the point where you can see it with your own eyes In the case of the Grom, the hard vibration that comes out when you rotate it is reduced rather than the vibration that comes out of it is reduced I feel like my hands are less likely to go numb
I think the quality of the product is high The GuardBody of the round bar is not so good parenthesis, but it is This product is highly recommended for those who pursue function rather than looks, and it's three birds with one stone It is
I think I'll change to the short lever But it's a waste of time and the U-KANAYA Lever is very good!
View detail
Why don't we stop with the button bolt?
This is another one of those products that I thought was packed with Race's know how, just like OUTEX To be honest, when I saw the product itself that arrived in the mail Why is this so expensive? I think that's about the extent of it (the processing is beautiful!) I guess you can think of it as a "know how" fee That's how unique this Maniac project is
First of all, our 2019 JC75 for our 2019 JC75 is the one with the model number SS17, not SS16! I ordered the SS16 at first because I couldn't tell the difference, but then I ordered the Cancellation, re I ordered it (We-Big, thank you for your time)
Installation is easy Basically However, maintenance novices like me should be very careful First of all, the OEM Bolt is tightened with the Demon Torque, because it's an M8 Cap bolt It's quite sturdy, but still, 1pc. licked After struggling for four or eight hours, I finally removed it and followed the Instruction Manual to Stem Install the Stabilizer Be careful again at this point The bottom two are the same M8 Cap Bolt but for some reason only the top one is Button A rare Bolt called Bolt is used (not available at the nearby Homsen), the M8 The Button bolt is tightened with 24Nm, and this Button bolt has a Hexagonal of 5 I licked it because of its millimeter size, and I think this Head is a no-go against Torque! (If you're good at it, it won't be a problem) And after all, I had a hard time rescuing the original Button bolt and I replaced it with an M8 Cap Bolt that I bought from Homsen As a result, there is no problem Is there some kind of first-class attention to detail here, OUTEX? However, the difficulty of Assembly is Number one For the layman, I'd like to see it be a little more Friendly Spec So I can't recommend it to everyone
So, how does it work? We are replacing the rear suspension with the NITRON R1 and at the same time, this Since I added Stem Stabilizer, the effect of the rear suspension is considerably increased As a result, it's a little questionable whether Stubby itself is properly rated or not I thought that Rear would be suitably hard, so I thought I'd be able to make it harder The intention was to tighten up the poor front fork as much as possible In fact, NITRON's Shock is very comfortable to ride and is not at all like the OEM product It does a good job that is incomparable So I don't have the impression that it has become harder (oh, in the NITRON imprecise) (It wasn't there) So, of course my pace goes up, but in the past, when the road surface is rough in Corner and so on, I would have been able to go to Oops! Take it! The Front has settled down even when it was in a difficult situation Clearly, the strange movement like twisting is suppressed, and the balance of the front and rear was also worrying The goodness of traceability that you can really immerse yourself in riding, even if the road surface is rough I feel secure enough to go ahead and leave the Lean Angle intact
After all, this effect is a know-how that only Mr. OUTEX, trained in MOTARD, can provide I think so Further up the ladder, you'll finally want to change the front suspension as well, but first you'll need to change the Spring and I think you can get some setting out with Fork oil (no, I don't think Setting doesn't mean that you can't shave off the time in Race, it's just an everyday (It's for the fun of Riding)
As a product for amateurs, I would like to complain a little bit, but the undercarriage of the I thought it would definitely contribute to LevelUp
Oh, and my name is Takegawa Filter:the head of the Bolt hits the air cleaner box, but it's not the same as the air cleaner box Riding-wise there is nothing wrong with it If it is used for a long time, it may get a scratch, but a hole will not open The wound of the black resin which is in an invisible place is not related
View detail
It can be installed on the MONKEY125
I bought it based on the impressions of others It is for the Grom and I was able to install it Naturally, the funnel does not face the front because the shape is different I don't feel the effect but I'm satisfied with it I'm expecting the special version to be released View detail
It looks cheap compared to the Lever Guard
The quality of the Lever Guard is so high that the Color:Unpainted Material:Plastic looks cheap
Or are you assuming that the buyer will paint it to their liking? I'd be willing to pay twice this price if the texture was better
I don't know the effect
Well, I've had bugs and stuff on my hands in the summer so far, but do you think that will go away? I don't think it's going to keep the winter cold out Maybe
View detail
Fits: YAMAHA WR250R, YAMAHA WR250X, YAMAHA WR250R, YAMAHA WR250X
Collaboration with OEMScreen! It was able to install as well
I finished installing it successfully (≧ ∀ ≦)
It took time to install because it was troubled how to do OEMScreen collaboration of Y's GEAR (Lol)
Fearfully mounting and retightening while confirming.
I was able to install it safely without mounting load almost required!
View detail
Fits: YAMAHA WR250R, YAMAHA WR250X, YAMAHA WR250R, YAMAHA WR250X
Step up with Upfootpeg !!!!
Time was not shortened so easily ...
OUTEX's Up Footpeg Bracket
DRC 5mm Up Wide Footpeg
I was able to raise footpeg a total of 12 mm
As for replacement, removal of OEM's Bracket is the largest Large change
People without Impact are safe to have them removed at the Motorcycle shop
Brake side can be misplaced by removing the Pedal axis and MASTER.
Although it aimed at improving bank angle and operability of Pedal, the former could be improved and the latter would not change very much
People who do not run like Dirt like Brett's Tilt Footpeg regret that it might have been better to put a footpeg on it
View detail