Reviews
I'm very happy with it
I think the quality and rigidity is very good.
The top screw hole is 5mm hexagon and easy to lick, so you need to be careful.
If you're replacing the Filter on your Air box with Other Brand Product, I think you'll hit a little Screw.
View detail
To prevent squeaking
I was looking for a replacement for the exhaust spring because of the rattling noise and this product came to my attention.:1 Set of 10pcs. is enough for you to stock if you have extra. The heat resistant rubber will reduce the vibration and rusting sound. View detail
Fits: KAWASAKI , KAWASAKI W400, KAWASAKI W650, KAWASAKI W800
It's a bit of a hassle, but...
I installed the Tubeless Kit that I have been curious about for a long time at Timing Tire Replacement.
Fortunately, I haven't experienced puncture with my current W800, and I bought it more for the peace of mind of not losing air too rapidly even if I hit a nail than to reduce the repair cost when punctured.
If you follow the friendly instructions, you won't get lost.
The procedure is...
Remove the tire from the vehicle.
Drop the Bead of Tire.
Unplug the tube.
Remove the Tire from the Rim.
Finish the welding part of Rim to Beauty.
Spoke's Nipple tip BALI take.
Clean and degrease the inside of the Rim.
Paste the NippleTape to all parts.
Wrap the masking tape around it.
Wrap the Seal tape around both sides.
Wrap the heat-resistant protective seat.
Install Air Valve.
Tire installation.
Air leak confirmed.
Installation on the vehicle
It's easy to write, but it's quite troublesome.
If you don't cover the Nipple area beautifully, it will cause air leak. If you don't do the work well, you will have to reassemble the tires like I did. (Lol)
In addition, in the case of W800, there is a step on the rear wheel to make it difficult for the tire head to fall, and it is difficult to drop and raise the head.
Because of the above reason, I think it is difficult to inject air without using Compressor at once.
Also, I think it's better to change the Rear Air Valve to L-Type than the Straight Type that comes with the kit for easier air adjustment.
I've actually used it to...
First of all, I left it for about 2 weeks and drove about 200km as it was, but there was no air leak.
I think it's not bad.
As for the request, the width of the Seal tape on both sides is Limit, so I want you to make it a little thicker and the price is high.
It won't prevent Puncture, but it will give you more Tire options, and if you carry a Repair Kit, you can complete the repair on the spot.
LargeOne less thing to worry about on my favorite touring trip.
It took a lot of work, but I'm recommending it for vehicles other than the W800.
View detail
I think I can reduce the vibration.
When I am riding DL1000 V-STROM250, because my hand was numb every SA when cruising on the expressway, I came to purchase because I found this product while I did a lot of research!
I think the packaging was fine.
I got a beautiful one.
I chose the Type of VALG-S-16, I think it was Exactly!
The product comes with a detailed Instruction Manual and other information, so beginners should have no problem.
The DL1000 V-STROM250 has a habit of leaving Nut inside the Bar End when removing it, so please check before removing it.
What I personally found to be a problem was the tightening Torque.
The Instruction Manual says to tighten the M8 bolt to 25Nm, but I didn't have a tool on hand that could tighten it to 25Nm Torque.
I didn't know about the tightening torque until I read the instruction manual.
I couldn't be bothered to buy a new Torque wrench for this, so I had no choice but to do it by hand Torque!
If possible, I would have liked to see the required tools listed somewhere in advance!
I don't have any concerns about the appearance of the product.
Although I was wearing Inner Gloves, the performance of the bike was very good, and I was able to do my annual touring to Venus Line. (About 200 km one way) And the numbness is only slightly felt.
I've had enough change to recover quickly after a break.
It's pretty dramatic, and I think the longer the distance, the better the performance will be.
In the first place, Lever Guard itself is very expensive, but if Lever Guard + vibration reduction for this amount of gold, the cost is relatively good, isn't it? I feel that
I'm generally satisfied.
I can't say anything about it as I haven't tightened it to the prescribed Torque, but I am concerned that the Lever might drop with a little vibration or contact.
To be honest, I'm not convinced, but I'm not sure if I want to buy the Torque wrench.
View detail
Good. ♪
Stainless Steel, no resonance and cheap.
No complaints at all.
View detail
Increased rigidity around the front
Installed on JC75
After installation, there was no change in the Handlebar angle.
It only felt like a change.
It's not so easy to tell if it's a low speed corner or not.
Just in Corner from Hard brake!
Grom, the characteristic squishy feeling becomes a firm Handling!
Handling is also a little quicker.
Handlebar Lock also works properly!
I'm glad I put mine on.
View detail
Stainless Steel Spring
I bought this because I installed a different silencer this time and the spring length doesn't match. I'm happy with the Large variant because it's cheap and good quality. View detail
Fits: KAWASAKI D Tracker X, SUZUKI 250SB, KAWASAKI D-TRACKER [D-Tracker]., KAWASAKI KLX250, KAWASAKI D Tracker X, SUZUKI 250SB, KAWASAKI D-TRACKER [D-Tracker]., KAWASAKI KLX250
Increased rigidity around the front
Chattering in the Corner and
The stiffness when braking has also been improved.
I'm glad I put it on.
View detail
Fits: HONDA , HONDA XR230, HONDA XR250 Motard, SUZUKI 250SB, その他 , KAWASAKI D tracker
Now you can say goodbye to the tube.
The preprocessing is quite Large strange, but I was able to make it Well and Tubeless even with amateur work.
This will save weight, eliminate the sudden drop in air pressure caused by puncture, and make tire changes easier in the future.
If the price was lower, it would be 5 stars.
View detail
Easy to install
After switching from the 600SS to the MOTARD, I was worried about the front wheel slipping when the speed range increased, so I bought this as a countermeasure.
First of all, even a layman can feel that the rigidity has increased.
It can be installed with Bolt On, so it was very durable.
However, the feeling of fluttering in town driving is naturally reduced, so how you perceive that may be the difference in satisfaction.
If you ride a MOTARD and play around on a mini circuit, I think you can recommend it.
View detail
Fits: Others , KAWASAKI D-TRACKER-X, KAWASAKI D Tracker, その他 , KAWASAKI D tracker, KAWASAKI D Tracker X
Tubeless is the best?
Tubeless was installed along with the 17in. Wide Rim of SR. Because the Instruction Manual with clear pictures is attached, the work was done smoothly...
I had to remove and install the tire 3 times before and after due to installation error.
It's been 3 days since installation and the air pressure hasn't decreased, so I think it's Large strong.
I will comment again after the installation on the vehicle.
View detail
This Size was perfect for my crf125F!
Item number:VALG-S-18
I put it on just in case because I don't have the OEM Clutch lever in stock, and because the Clutch lever is long, you have to move the Clamp of the Clutch lever to the HandlebarCenter or it will interfere.
View detail
Fits: YAMAHA WR250R, YAMAHA WR250X, YAMAHA WR250R, YAMAHA WR250X
Outex Steering Stem Stabilizer
Not only do these little brackets look good, they'll stiffen the front end and improve rideability. These are some trick brackets. View detail
No more vibration during normal driving.
I installed it on CBR1000RR-R SP.
Because of the vibration caused by the new Handlebar.
I bought the wrong inner diameter of the Handlebar when I ordered it, so I ordered an extra hex to change it and installed it, and the result is no vibration and I think I bought a great product.
View detail
Vibration Absorption Lever Guard and Quantity:Recommendations in Set
I had a Vibration Absorption Lever Guard installed on the glom.
It's cold in the winter time, so I thought I'd wear my Knuckle guard too, and I found a Bracket that might come in handy!
Of course, OUTEX has Knuckle guard for Lever Guard and Exclusive Bracket, but you can use other company's one if you have Bolt hole on Knuckle guard side.
I installed a ZETA X2Protector.
I think the exclusive product for OUTEX is the Black color Knuckle guard, but it can be used by other companies, so it's convenient for customization to match your vehicle color!
The body color of the Grom is Loss white, so I installed White&Red Protector to match it.
(The image is blue due to the color of the LED light, but the actual color is the same as Grom's body color, a proper white color)
I was able to install the bolt with no problem using the bolt that originally came with the OUTEX L-shaped clamp.
It is a good product that combines convenience and customization.
View detail
DIDfor RaceWheel rim, machining is extremely difficult.
I tried to do Tubeless processing on a TDRRacing wheel for MOTARD by myself. As a result, I had to repeatedly remove and install the tire 4 times for air leak repair. (T ^ T) I know this, but the FR rim is deeper than I expected. I knew this, but the Rim of FR is deeper than expected and I can't cover the wall side well with Tape. I thought I had bought a special one, but it was a little narrower than I expected. View detail
Fits: HONDA CB250RS, HONDA GB250 Clubman, KAWASAKI estrea, YAMAHA SR400, YAMAHA SR500
Tube Eliminate Kit OUTEX
First of all, I think it's good that the air doesn't go out immediately after puncture and Repair is easy.
Safety is number one.
What it felt like driving from Tube to Tubeless.
I feel lighter.
I think it is a very good product.
In the case of SR400OEMWheel, the place to put the tape is "R", so if you pay attention to the place to put the tape, you don't need any force.
Because if you put air in it, it will push against the air pressure by itself.
However, it was very large and strange to fit the tire to the wheel.
Also, we have to take Balance.
If you are going to install it yourself, I think you should ask Shop or install it by yourself considering that Tire replacement will be Large strange.
Next time I change my tires, I'm going to try some backdoor installation with Tie Band or something.
View detail
Fits: HONDA , HONDA XR230, HONDA XR250 Motard, SUZUKI 250SB, その他 , KAWASAKI D tracker
Tubeless
Although it cannot be said with a loud voice, because this transparent Double-sided Tape was used at work, it thought that it would do it by itself at first. However, when I checked out the wide one at a certain famous store, I found that it was very expensive. If the protective tape, Valve for Tubeless, and the procedure manual are attached, this price is also unavoidable. After obtaining, when Wheel is opened, the mark which shaved the mountain of welding is too much shaved. If I make the shaving mark completely beautiful, it becomes flat only there and it doesn't become a circumference no matter how I think. The procedure has no material to judge how far it should be driven in such a case. It would have been nice if there was a photo printed in Large format, like "Large is strong enough for this degree from construction results. After the installation, there is no air leak and I feel the front is lighter. I should have done it earlier. View detail
Fits: HONDA , HONDA XR400 Motard, YAMAHA , YAMAHA WR250X, その他
Spring lowering weight reduction
It was installed in 2007 wr250x from the time of purchase. I was troubled that Handling was light and the setting of Suspension was very different compared with 2009 wr250x which I owned before, but because Rosso3 died at 6000 the other day, when I exchanged it, it turned out that it was processed Tubeless. It is lucky that the most large Merit of the tubeless processing can be punctured easily with the puncture repair kit of the market. View detail
No complaints about the product
[How is it used?
Commuting Touring
Was the one you received as per Image?
Yes
Was the installation difficult?
No
How was your experience with it?
Reduced Handlebar Vibration
No more twisting of the Front hawks at Corner, I feel more secure.
[Included Parts:were they on?
Yes
[Was there anything that disappointed you?
I wish the Bolt that came with it was Stainless Steel.
Other items that would be helpful
Point and hang of installation/Be sure to work one side at a time! It may be slippery when tightening the upper Bolt!
Availability and clarity of the Instruction Manual/A little difficult to see in WhiteBlack
Cautions/None in particular
Items to buy together/None
View detail