Reviews
Stabilizer
I thought it wouldn't make much difference if I added just a board like this, so I added it just for looks.
I didn't notice much change just by commuting to work, so I went for a run in the nearby mountains and found that the handlebar was much snappier and the handlebar was less shaky even at the Corner, making it easier to turn.
Bigli.
View detail
Classic type
Installation was very easy. It took a bit of time to remove the no-mar, but it was a basic one-piece installation.
The sound is not so loud when Idling, but it sounds good when accelerating.
I think the acceleration from 65 km/h or more has improved, but I'm not sure if it's the sound. I think it might be the sound.
I love it!
View detail
Fits: HONDA , HONDA XR230, HONDA XR250 Motard, SUZUKI 250SB, その他 , KAWASAKI D tracker
Perseverance is a must.
It was quite a large job, starting with the preparation of the wheel (the work content changed depending on the wheel's condition), double-sided taping, and protective taping.
(Some of the Wheel was in bad shape.)
Double-sided tape pasting is very difficult.
(I wanted to put it on Beauty but couldn't. If I could have stuck it there, it would have been Large sturdy. (I wanted to stick it to Beauty but I couldn't, but Large was tough enough to stick it there.)
Protective Tape could be applied to Beauty if applied calmly.
It took a lot of patience, but I am happy that I was able to make it Tubeless and wear Radial.
View detail
Fits: その他
Handlebarfor Replacement
I purchased this product to change the handlebar diameter when replacing a MORIWAKI handlebar with a ZETA handlebar. This product is a recommendation because there are many different types of Adapters to fit any handlebar diameter, so you can easily change the handlebar. View detail
Fits: HONDA , HONDA CB750FOUR, HONDA CB750K, KAWASAKI , KAWASAKI 250TR, KAWASAKI KZ650, KAWASAKI W1, KAWASAKI Z-1, KAWASAKI Z-2, SUZUKI GT750, YAMAHA BRONCO
Purchased for CB750four
Purchased both Front and Rear.
I started with the rear tire first and followed the instructions to install it without any problems.
A year later, I installed it in conjunction with the replacement of the front tire, but the joint between the rim and the double-sided tape was not properly connected.
It did not work and I gave up on this one. Maybe a year has passed and the adhesive strength of Tape has weakened.
You may
I couldn't see any difference in the ride quality after installing the Tubeless.
The cost is not so good, because it is more expensive for the
The satisfaction is the DIY sense of accomplishment and the relief when the Tire is inflated and there are no leaks.
View detail
Surprisingly easy! Tubelessness is Merit Extremely Large!
[How is it used?
Tubeless conversion of KAWASAKI D-TRACKER125 + installation of block tie rear
Was the one you received as per Image?
As shown in the product photo
Was the installation difficult?
The front wheels failed a bit, but the rear wheels succeeded. No problems at all using the front wheels either.
How was your experience with it?
I can put a block tie rear on my D-TRACKER125, which has almost no tire options, and I don't have to puncture it,
The drop in air pressure is no different than with the Tube. The sense of security when going into the mountains is very different!
[Included Parts:were they on?
Included Parts:were all in place as shown in the photo.
[Was there anything that disappointed you?
none at all
Point and hang of installation
Please see my journal (https://imp.webike.net/diary/237245/)
[ITEMS TO BUY TOGETHER
IRC PROTECH FOOTLOOSE GP-22 110/80-14 53P TL
[Availability and clarity of the Instruction Manual
I thought anyone could do it by watching the YouTube that Manufacturer gives. At least I could!
View detail
Fits: HONDA CT125CT110 HUNTER CUB, HONDA CT125CT110 HUNTER CUB
Effect of CT125 Stem Stabilizer
[Motivation for purchase]
I cannot drive the CT125 at high speeds, but I was concerned about the low rigidity of the front part of the bike, as the front part begins to vibrate at around 60 km/h and becomes unstable when breaking.
[Effect]
The rigidity of the front part has been increased, and vibration and instability are no longer felt.I cannot feel the Quickness of the Handling, but I feel that driving stability has clearly improved. The rigidity of the entire vehicle body also seems to have increased, and the feeling of Torque being transmitted to the ground has become stronger.
However, due to the increased rigidity, the front suspension now pushes up. We have been adjusting the blend of different viscosity fork oil to prevent the push-up, but we may have to think about replacing the front suspension.
[Others]
The instruction manual is very clear and easy to understand. The pictures are included in the manual, but they are not clear enough to understand.
View detail
Front rigidity of JC75 is increased.
Installation is easy
Front rigidity is increased and breaking is stabilized.
It looks good.
It is also good that it is different from the OEM Front fork Gold.
View detail
It was easy to install.
690smcr (21 years) attached to the
The work was very easy and the Instruction Manual was included in case of any problems.
In the case of the 690, the OEM Knuckle guard is attached, so if you remove it, the clutch lever will also come off, so if you have a separate m6 nut, you can fix it.
Vibration absorption effect, but there is no overt reduction in vibration.
I was wondering if it was less than before it was installed.
I was more satisfied with the visual coolness of the product.
View detail
Fits: FANTIC Fanatic Caballero Rally 500, ROYAL ENFIELD Interceptor 650, ROYAL ENFIELD Continental GT650, その他
No problem the first time if carefully installed.
Used to make SR400's Rear wheel tubeless.
We installed it not only to reduce weight, but also because we originally had Tire on Tubeless Casting wheel and to eliminate the anxiety of puncture on the road.
The subject of the installation was an SR400 hub with EXCEL's AluminumWide Rim.
The size is 18×MT3.5J. I have the impression that MTRim was not as difficult as I thought it would be, probably because the surface that Nipple sticks to is the back.
I think it was a good thing that it was a new rim, but even so, I smoothed the mating surfaces of the rim with water-resistance paper just in case.
I think a used OEMRim or H-type Rim would increase the difficulty.
Due to the nature of the product, re-installation is quite Large strange, so at least a new Spoke seems like a good idea.
Also, if the RimCenter is narrow, such as almost only the width of the Nipple, the difficulty seems to increase even more.
This was my first installation, but I worked carefully anyway, even if it took some time.
Not included in the kit but necessary are water-resistance paper for leveling the rim joint surfaces and a strong parts cleaner for degreasing.
I was lent WAKOS Parts cleaner by a colleague of mine, as it is said to have a different cleaning power.
It was supposed to be a new rim, but Dustcloth was very dirty, so I thought it was definitely a necessary process.
After installation, the tires were immediately assembled and left at high air pressure.
2.The manual said 5 kilos, but I put in 3.0 kilos because I usually have a habit of setting the Tire higher right after it is built in.
Check two days later and it is still a Large success.
Overall, it is not difficult, but it is depressing that I have to install it on the Front from now on because it was quite Large strange lol.
(even more so since Front is 2.5J)
View detail
Stability Up
After test driving straight ahead and in the corner, the straight ahead stability and the handlebar shake was reduced, and the car feels stable even at 80 km/h.
Installation is also done with the car's Jack under the Engine.:Set and worked on it, but it is easy to work with.
Color and Bolt1 pc and WasherQuantity on top:1pc., color and BoltQuantity below:All you need to do is install 2pcs and 2 washers.
View detail
Fits: HONDA , HONDA , HONDA CRF250L, HONDA the rest, HUSQVARNA TE450, HUSQVARNA the rest, KAWASAKI supersherpa, KAWASAKI the rest, SUZUKI DR-Z400S, SUZUKI the rest, YAMAHA , YAMAHA , YAMAHA WR250R, YAMAHA the rest
Perfect Item As Advertised
Ordered on 26 March 2023, shipped on 27 March 2023. Arrives Brunei on 31 March 2023 by DHL. Took 5 days to arrives. This item will be used to tape my supermoto wheel on CRF250L 2014. View detail
Fits: APRILIA SXV450, APRILIA SXV550, DUCATI sports classic, DUCATI Pole Smart, KTM , Norton command, SUZUKI , SUZUKI DR-Z400SM, TRIUMPH Thruxton R, YAMAHA TW200, YAMAHA TW225, その他 , その他 , その他 , その他
It can be easily made Tubeless!
Once you get the gist of it, you can easily make it Tubeless with ease.
Videos are also available on YouTube, so if you watch them while installing, the hurdle will be lowered.
The durability is also quite good, and after two years of installation, there is still no excessive air loss.
But the price is high.
It would be better if it were cheaper.
View detail
Fits: HONDA , HONDA CRF1000L Africa Twin, KTM 950 ADV, KTM 990ADV, TRIUMPH NEW Tiger 800XC, その他
Honda africa twin
The product is good quality,easy to repair and handle. The kit is complete ready to use. Safety is number one. What it felt like driving from tube to tubeless. I feel lighter. I think it... View detail
Fits: KTM 950SUPERMOTO, KTM 990ADVENTURE, KTM 990SUPER DUKE R, KTM 990SUPER DUKE, KTM 990 SUPERMOTO, KTM 690SUPERMOTO, KTM 690SMC R, KTM 690SMC, KTM 690DUKE, KTM 690ENDURO, KTM 200DUKE, KTM 390DUKE
I saw that it was for car models only.
You can't use it, so all you can do is complain! With rising prices, Cup noodles are also increasing in price.
What a waste! I'm going to eat an ear of bread for a while!
View detail
You can feel the rigidity increase!
Purchased a Honda Grom (JC92 new car) in June 2022.
I was concerned about the lightness and unstable movement of the Handlebar at high speeds, so I purchased this product.
The installation method was to fix the for VehicleJack under the Engine, and carefully to prevent the Stem from lowering.
Material because Rust is also a concern for Screws.:Replaced with Stainless Steel.
Here we go! First run!
I could feel the stiffness of the front suspension right from the start, and I was impressed that the handlebar was calm even when the road surface was uneven.
I was skeptical, but it was the right decision to purchase Large.
I am looking forward to Touring in the future.
View detail
Stem Stabilizer installed
I bought it as soon as I saw that MotoBlogger had installed it.
I had to wait a bit for the Red2 to match the color of my DAX125.
If you have waited long enough.
The cut-out aluminum parts add to the sense of ownership, and the installation instruction manual was translated (just type it in here), so it was easy to install!
ThailandHondaQuality so it takes a little bit of force to loosen Bolt.
Note only that tightening with the same force that loosened it will result in Overtorque.
It is fun to drive because you can trace the line you are aiming for when turning a corner.
Before installation, I had to be careful not to cut the handlebar too much, but now that the shock has been stiffened up, I feel that the original performance has been fully realized.
It is a recommendation because the performance is better than the price.
View detail
Dress-up and Rigidity Up
Installation is easy
Simply tighten to match the specified Torque.
The workmanship is very careful and beautifully finished.
It is also a hidden dress-up, killing two birds with one stone.
View detail
Fits: HONDA glom, HONDA MONKEY125
Appearance Up
Vibrations are much less than before installation.
It is also a dress-up, so it is a recommendation.
View detail
It is easy to install.
Small and stylish, it is less windproof. However, it is good because it is somewhat effective. View detail