Reviews
To prevent heat leaks.
At first, I thought that a bore up to about 88 would not need an air conditioner, but I was worried about it in the summer because I ride the car with it cranked up quite a bit.
good point
The heat of the Engine is reduced a little.
Oil stains are also a little better.
Engine noise is also reduced.
A bad point
Expensive.
Installation is quite troublesome.
It is expensive and troublesome, but once installed, it is as effective as the installation itself.
To begin with, since the engine designed for 50cc is forced to be bored up, the heat value is beyond the range, and if the budget allows, it is better to put it on.
View detail
To APETypeD
Installation is easy as long as you follow the instruction manual.
You will need a stand holder for Rear Sets and a kick pedal.
View detail
It took a while, but I had fun while doing it.
Installed on SUPER CUB 50FI AA01-175＊＊＊＊.
It was my first time to work on a Bore up engineCustom, and I had a lot of trouble reassembling and rooting, but I finally finished it.
I gave it 3 stars because I'm going to break it in and I don't know how durable it is yet.
It was a large and strange task for an amateur, but I enjoyed it.
At the same time, we replaced the Takegawa Reinforced Clutch and Oil pump, and installed the FI Controller and Oil cooler.
I'm also planning to replace the Air Filter, BigThrottle and Injector.
View detail
26ΦThrottle
ThrottleLarge, but I can really feel the tenacity on the uphill.
CUB.
View detail
It's easy to image chain
Matching with Clear tail of Takegawa is also good. I have no complaint. View detail
Fits: HONDA Super Cub 50, HONDA LITTLE CUB, HONDA CUB press 50
Engine Displacement VolumeUp for CUB's CampingTwoCustom!
I decided to Bore up on the SUPER CUB 90 to make it a little easier for me to go camping with it!
I bought it because with Bore up, the NORMAL carburetor could no longer support the setting.
The air cleaner side can be installed in a NORMAL state, but as it is, there is not much air to breathe.
I also changed the Filter and adjusted the Big Cab because I couldn't make the most of it.
View detail
Fits: HONDA Super Cub 50, HONDA LITTLE CUB, HONDA CUB press 50
Bore up and the simultaneous replacement of the effect Large
[Was there anything that disappointed you?
Generally satisfied
However, there are two points that require improvement in the design, as described below
Do you have any wishes or improvements you would like to make for the Manufacturer?
The accuracy of the joint parts of Carburetor and Manifold is similar to KITACO and others It's not a good comparison, so Material:It would be good to improve on Plastic's same etc. products
I don't know if it's the effect of individual differences, but the height of the Manifold is lower than the height of the Air cleaner The frame attachment part is lowered, so we had to lift it up
I think the Clearance setting with the vehicle needs to be improved
[Do you have any products to compare it to?
SP Takekawa PB16Big Carburetor
I chose this product because of the price difference
What made you decide to buy?
I wanted to keep the intake noise quiet, so I could use the NORMAL air cleaner and I like the fact that the NORMAL Choke Lever can be used as is
The price is also a decisive factor in comparison to the SP Mukawa PB16, which is about 60% less expensive
How was your experience with it?
The synergy of Bore up and other factors has clearly increased the horsepower
But maybe it's just a characteristic of this Carburetor, or maybe it's just that the Engine can't restart after it's fully warmed up The Engine won't start unless you adjust the Timing and open the Throttle a bit, which is a habit Impression (It didn't take nearly as long for a single KICK to take place.)
I wish I could improve it in Settings...
Was the installation difficult?
It's as easy as the Instruction Manual
【Please tell me the installation point and hang】
When you remove the carburetor from the carburetor in use, you need to set the bolts to the fuel hose If you don't do this, Gasoline will keep coming out until the tank is empty, so you must do this beforehand
[Was the Instruction Manual easy to understand?
There is no shortage of content to install
[Included Parts:were they on?
Gasket and other necessary items are available
[Others]
For the porting of the head for performance, Manifold has been designed by KITACO for PC20
View detail