Reviews
Enough for Sunday mechanic
[How is it used?
STAND and Exhaust System during vehicle maintenance (Chamber) It is used to remove and install Spring for replacement etc.
Before purchasing this product, I had been working hard with a radipen, but I purchased this product to increase work efficiency.
Was the one you received as per Image?
It was just like the picture.
How was your experience with it?
The hook is processed so that the tip of the hook is tapered, allowing for smooth attachment and removal of the spring.
Also, the T-section is well reinforced, and although it is inexpensive, it does not seem to break easily.
The size is neither too small nor too large, but just right.
[Points to note]
None in particular. Surprisingly comes into play when it comes to maintenance.
How did it compare to other products?
This product has no problem, but some of the ones I used in the past had no reinforcement at the T-junction and would break off.
This is a part where force is inevitably applied, so I think this product is good because that part is reinforced.
【Review】
It is fairly inexpensive, but I think it works well for starters.
As expected, the durability will be inferior to those of famous manufacturers when used over a long period of time, but I think it will be sufficient for Sunday mechanicLevel.
View detail
For safe operation
Purchased for my own Exhaust System replacement.
When installing the Exhaust Spring, it requires a lot of force and the body position is low, so it is a good idea to have it in order to prevent the Exhaust System from getting damaged and to prevent injury to the driver.
This product is 150mm long (measured after purchase) I can't say for sure because the force depends on the type of Exhaust Spring, but I was able to use it without any problems.
It is also a simple product and not used very often, but it is reasonably priced.
View detail
Cheap and convenient.
This spring hook is very useful and inexpensive, and it is a must-have for the removal of the Full Exhaust System, so you don't have to worry about the wound sticking to the exhaust pipe, and you don't have to worry about injuring yourself by pulling with pliers. The Grip is easy to handle and is very easy to pull. View detail
Fits: YAMAHA CYGNUS125 [Cygnus] (new model), YAMAHA MAJESTY125 [Majesty]., YAMAHA CYGNUS125 [Cygnus]., YAMAHA CYGNUS125 [Cygnus] (new model), YAMAHA MAJESTY125 [Majesty]., YAMAHA CYGNUS125 [Cygnus].
I do not feel the price difference in a good sense
'07 Used with CYGNUS X.
Distortion is intense in the Sample picture, so I bought it while preparing it ...
The item that arrived is flat to Beauty, rather it is the Level where the KITACO made Wrench is more distorted.
Rather than 46 mm 46. Although it is a size such as 5 mm, since it is 6th Wrench, there is no practical problem.
I tried shivering with Hammer when loosening Nut, but somewhat dented but without Plating peeling,
Demerit by the cheap overall is not felt much.
Considering the frequency of Clutch desorption, I think that this is enough.
View detail
I could use it normally
Used for Spring fixed to the Flange section of External Chamber outside the company
It was quite hard Spring, but it worked without problem. I was worried because it is cheap, but I think it's tough..
View detail
Fits: YAMAHA CYGNUS125 [Cygnus] (new model), YAMAHA MAJESTY125 [Majesty]., YAMAHA CYGNUS125 [Cygnus]., YAMAHA CYGNUS125 [Cygnus] (new model), YAMAHA MAJESTY125 [Majesty]., YAMAHA CYGNUS125 [Cygnus].
Yamaha motor scooter special tool
Purchased for MAJESTY 125 maintenance. I bought it because I did not have that Lock nut was a dedicated Size and the price was also cheap. It was very cheap, so I am a little worried, but I still have to use durability from now on. Continue to use and understand something, I will write.
View detail
It is a good product.
I bought it because the price was cheap and it seemed easy to use. It was actually easy to use. I was very happy because it was too early to order from ordering to hand. View detail