Reviews
Fits: HARLEY-DAVIDSON Pan America 1250, HARLEY-DAVIDSON Pan America 1250 Special
As a heat damage prevention
I installed the radiator hose to prevent the heat from the exhaust pipe from melting in PanUnited States. I don't know how effective it is, but I think it is good. View detail
Fits: BMW R18, BMW R18B, BMW R18 Transcontinental, BMW R18 Classic, BMW R18 Roctane
For your peace of mind in case of emergency
The R18B's Front Fender is long and I wondered if protection would be necessary. However, I installed it in case the fins of the oil cooler were damaged. I don't know how well it works, but it looks better!
Before the installation of the grille, the oil cooler area was all black, but now I like it because it blends well with the plating on the exhaust pipe, engine guard, and other parts. I think it will be more useful especially on the R18, since it is a short fender.
View detail
Fits: BMW S1000R, BMW S1000XR, BMW S1000R, BMW S1000XR, BMW S1000RR, BMW S1000RR, BMW S1000RR, BMW S1000RR, BMW S1000RR, BMW S1000R, BMW RnineT, BMW R1200RT, BMW RnineT, BMW R1200RT, BMW R1200R, BMW R1200R, BMW R1200GS, BMW R1200GS, BMW R1200GS, BMW K1200GT
Used for R ninet Racer
I bought this one because I use Wonderlich's Magnet Drain Bolt.
Batch
View detail
Fits: BMW R1250R, BMW R1250RS, BMW R1250RS, BMW R1250R, BMW R1250RT, BMW R1250RT
It was unexpectedly small.
I installed it in the hope of protecting the EngineHousing from small stones rolled up by the front tire, but the protective part was narrower than I expected.
I guess I should have checked the Size carefully, but I thought the protection of EngineHousing was limited.
It may be possible to extend the scope of protection by using it with a product that extends the Front Fender, but other products may also be acceptable.
However, the quality of the product is very good.
T27 is required for installation.
View detail
Fits: BMW R1200R LC water-cooled, BMW R1200RS LC water-cooled, BMW R1250R, BMW R1250RS
I was just a little worried.
I had a little trouble removing the OEM Radiator guard made of Plastic when installing it.
Loosen the two T20 screws at the bottom of the Radiator and you are good to go.
The electric fan is also fastened together with the OEM radiator guard, so even when the guard is removed and attached, the screws should be tightened as before.
After installation is complete, tighten the cowl screws again, but be careful because the part attached to the Radiator guard (the one that looks like a white dot) will quickly slip off.
View detail
Fits: BMW RnineT, BMW RnineT, BMW RnineT /5, BMW RnineT Urban G/S, BMW RnineT Scrambler, BMW RnineT Racer, BMW RnineT Pure
Standard Oil cooler guard
Standard Oil cooler guard.
I didn't think much about designability and left it up to the Dealer.
It is a standard product, so there are no complaints in terms of design or functionality. (^^^) /
The installation was done by Dealer at the time of delivery, so the degree of difficulty is unknown.
View detail
Fits: BMW S1000XR, BMW S1000R, BMW S1000R, BMW R1200RT, BMW R1200RT, BMW R1200R, BMW K1200GT, BMW R1200GS, BMW R1200GS, BMW R1200GS, BMW R1200R, BMW RnineT, BMW RnineT, BMW S1000R, BMW S1000RR, BMW S1000RR, BMW S1000RR, BMW S1000RR, BMW S1000RR, BMW S1000XR
Good.
I came to purchase the OEM Drain bolt because it was nerfed. This is the only one in stock that fits the Webike and it was a bit expensive. If it's a domestic product, there might be cheaper ones, but since I'm driving a foreign car, I'm not sure if I have to put up with that. View detail
Fits: BMW F650GS (08-), BMW F700GS (-16), BMW F800R (-11), BMW F800S, BMW F800R (12-14), BMW F650GS (08-), BMW F700GS (-16), BMW F800R (-11), BMW F800S, BMW F800R (12-14)
I do not run the forest road, but I think that it is necessary also on the ordinary road.
Every time the bicycle parking space is unpaved and everyday Motorcycle comes out, the stones are muddy. Even if you are running on an ordinary road after the rain, mud is still there, and a stone splash is normal. In such conditions, since mud is definitely among the fins of the water cooler, it has always been removed using Small Brush. About 80% of mud bounced by attaching this product prevents entry into Water cooler fins.
Installation seems easy, so it's quite Large strange. Shroud It is easy if you take it off, but if you try to attach it without removing it, you must put your hands from the narrow Duct of SIDE and you have to feel yourself screwed.
View detail