Reviews
Fits: BMW R1250RT, BMW R1250GS, BMW R1250GS Adventure, BMW R1200GS LC Liquid Cooling, BMW R1200GS LC Liquid Cooling, BMW R1200GS LC Adventure water-cooled
Elbow pain improvement
With the OEM position, there was no room for elbow bending and I had elbow pain after 2 hours of riding. After installing this Handlebar Up kit, it became easier to ride and the pain disappeared.
The brake hose was fine, but the clutch hose was sticking when the handlebar was cut to the right. So, I removed the exterior and took the part of the hose that had room from the base of the clutch to the lever side and fixed it with a tie band. I also shifted the Clutch leverBracket installation slightly inward to make more room for the hose. There may be individual differences in the body of the vehicle.
The installation of the Kit itself is easy, but if the Hose is propped up, the work will be a little more difficult.
View detail
Fits: BMW F850GS, BMW F750GS, BMW F900XR, BMW F900R, BMW RnineT, BMW RnineT Urban G/S, BMW RnineT Scrambler, BMW RnineT Pure, BMW RnineT /5, BMW R12 nineT, BMW R12
It's solid.
It is quite large and sturdy. I bought it because the back of my hands cannot stand the cold when touring in winter. In fact, when I used it, I always had to use the Grip heater, but I was OK with the Grip heater off. Even if I did use it, it was only one step, but it was Large sturdy. View detail
Fits: BMW R18, BMW R18 Classic, BMW R1250RT, BMW R1250RT, BMW R1250GS, BMW R1250GS Adventure, BMW R1200RT, BMW R1200ST, BMW R1200RT, BMW R1200R, BMW RnineT Racer, BMW RnineT Scrambler, BMW RnineT Urban G/S, BMW RnineT, BMW RnineT, BMW S1000XR, BMW S1000XR, BMW R1200R, BMW R1200GS, BMW R1200GS
Handlebar Cover is pampered
However, these are Handlebar Gloves, so they are safe.
I was able to install the GIVI Hand Guard ExtensionEH5108 with no problems.
View detail
Fits: BMW F850GS Adventure, BMW F850GS, BMW S1000XR, BMW F800GS Adventure, BMW F750GS, BMW R1250GS Adventure, BMW R1250GS, BMW F900XR, BMW F900GS Adventure, BMW F900GS, BMW S1000XR, BMW R1200GS LC Liquid Cooling, BMW R1200GS LC Liquid Cooling, BMW R1200GS LC Adventure water-cooled, BMW F800GS
I like it.
I was a little resistant at first, but when I installed it, it was good.
It is quite a favorite.
View detail
Fits: BMW R1250RT, BMW R1250GS, BMW R1250GS Adventure, BMW R1200GS LC Liquid Cooling, BMW R1200GS LC Liquid Cooling, BMW R1200GS LC Adventure water-cooled
Make riding more comfortable
My motorcycle is a BMW R1250GS. I feel a little tired after riding this bike for a long time, so I bought this Wunderlich handle heightening kit on webike. It can increase the height by 40mm, so that my arms can be bent and longer Time riding will not be so sore, and the overall workmanship is exquisite. I am very satisfied with this shopping. -------------------------------------------------- -------- My motorcycle is BMW R1250GS. I will feel a little tired in this bike for a long time, so I bought this Wunderlich handle high -handed kit on Webike. Time will not be so sour, the overall workmanship is also exquisite, and I am very satisfied with this shopping. Powered by Google Translator View detail
Fits: BMW RnineT, BMW RnineT, BMW RnineT Urban G/S, BMW RnineT Scrambler, BMW RnineT Pure, BMW RnineT /5
Boarding Position is now easier.
With my physique, the OEM Handlebar of the R nineT Pure is wide and forces me to lean forward a bit, but this Handlebar Up kit made it easier. I feel that the height has improved by about 100mm and the front by about 20mm.
The Axel wire is a little tight, but if the Body side is pulled out a little, the Handlebar Lock is still sturdy and large.
(At your own risk.)
View detail
We installed a European car to fit the body shape of Japanese people.
Purchase this product because the Position is slightly tilted forward in NORMAL mode. Note that there is an adapter position for installation. Also, it is recommended to use a torque wrench to check the torque of bolt tightening. (Insufficient torque or the order of tightening will cause the bolt to loosen.)
After the installation, the upper body was able to rise and long-distance touring became easier.
View detail
Fits: BMW S1000XR, BMW R1250RT, BMW R1250GS Adventure, BMW R1250GS, BMW R1200GS LC Liquid Cooling, BMW R1200GS LC Liquid Cooling, BMW R1200GS LC Adventure water-cooled
Cost performance outstanding!
BMW motorcycles are well-made motorcycles that are easy to ride for Japanese people. However, the design itself is tailored to the physique of Westerners, so the seat may be high and the handlebar may be far away.
I'm 170cm tall, but fortunately I was born with longer arms and legs than others, so I can enjoy riding the S1000XR even if it's a Large handlebar. However, after a long time of touring, fatigue in my arms and back starts to build up and it turns into pain.
I always felt that this was due to the distance of the Handlebar, after all. I was looking for something to do about it, and I found the Handlebar Up kit on the Wonderlich (Bar riser) I found that there was a "good" one, but I was honestly quite hesitant to purchase it because there was no Impression for the same model of car. However, the price was affordable, so I decided to take the adventure.
The item I received came in a palm size tiered ball box. The material of the tiered ball box was good and not the low quality paper that is often found in imported products. When I opened the box, I found the body and mounting bolts carefully wrapped in cream-colored recycled paper.:It is a very finely crafted finish in aluminum. As expected of Made In GERMANY, it is trustworthy to be able to understand the Japanese products.
However, I was disappointed that the Mounting Bolt was made of Chromium Plating steel instead of Stainless Steel.
About installation
If you don't have confidence in the installation, please ask your dealer to install it. Because the parts are expensive imported cars, if there is Trouble after installation, it is Large strange. Personal installation is done at your own risk.
It is easy to install the Handlebar riser itself, because it only has to be tightened with the attached Bolt, but it is listed below. You can use the Torx wrench, but if you want to focus on torque-management, I recommend the Socket wrench type.
Before starting, hang both ends of the Handlebar with a string from above. (If it's possible.) If you loosen the Handlebar SetBolt without doing anything, the Handlebar may fall down in front of you suddenly. So you should hang the Handlebar from the Handlebar SetBolt. And to prevent Wound, you should cover the whole Tank with the soft cloth.
Be careful not to put too much pressure on the handling of the Clutch wire, brake hose and wiring as the position of the handlebar will change.
If you follow the Clutch wire and Brake hose, you will find them around the steering head and into the Fairing on the Right Side of the car body.:Pair (for Left and Right) Remove the Right SideFairing to check if there is any strain on the wire and hose when fully locked to the
Loosen the 4 OEMSet bolts and pull out the bolts and free the Handlebar with Upper Holder. Check if the 4 bolts can be tightened lightly in this state. If the bolts are too heavy, remove them and try to fix the problem. (Screw Mountain Crush etc.) solution.
If you ruin the female Screw on the Steering head's Handlebar Holder, you'll have to pay a hell of a lot of money. Be careful.
Carefully lift the Handlebar. (The hanging strap is long and unstable.) 、Quantity:Pair (for Left and Right) The direction of the bar riser should be as shown in the Instruction Manual.
If you are able to pinch the bolts, use the attached Bolt as a quantity:Pair (for Left and Right) Insert 1 pc. at a time and lightly tighten it. At this time, you can adjust the length of the hanging string to adjust the position of the handlebar easily.
Remaining Quantity:Temporarily tighten the 4 bolts by adding 2pc, but if the bolts cannot be lightly tightened by bare hands, the bolt holes may not be aligned, so you may need to use the Handlebar for front and rear Quantity:Pair (for Left and Right) and tighten it to the temporary tightening position.
In my case, the subtle distortion of the attached Bolt (Eccentricity) So I put some grease on the part where the screw is not cut and tightened it again.
Check the tightening position of the handlebar.:Pair (for Left and Right) The final position is determined by actually gripping the Handlebar over the Seat to see if it is out of alignment with the Seat and if the Handlebar is not falling backwards or forward.
In my case, the Grip position was the most comfortable when it was fixed in the same position as the OEM.
Set 4 screws and apply a small amount of the liquid screw lock that comes with the Bar riser to the screw thread.:Tighten the 2pc first so that the Upper Holder and Bar riser are in tight contact. Then tighten the rear quantity:Tighten the 2pc with the prescribed torque and you're done. It is normal for the rear side to have a gap. Also, at this time, the handlebar position will change slightly, so check and readjust if necessary.
When the installation is complete, remove the hanging strap and place the Handlebar on the Quantity:Pair (for Left and Right) Turn it slowly until it hits the stopper of the Clutch wire and the Brake hose and check the tension of the Clutch wire and the Brake hose. If the brake hose is pulled strongly, especially when turned to Left, you will need to change to a longer hose.
In the case of my S1000XR, the Clutch Wire and Brake hose were LimitLarge sturdy with the OEM still in place. As expected, Wonderlich makes products with exquisite saltiness.
When I straddled it.
Before I installed it, I was in a riding position where I felt the Handlebar was far away. After installation, you can feel that you can reach Grip naturally when you sit on Seat and extend your hand. Moreover, it is natural, but I think that the tip from the Handlebar became long. I will get used to it.
When you actually drive it.
I couldn't take the time to do a test drive, so my first ride was a Tandem touring with my wife. RidingFeel is the same. I think that this is one step closer to an easy position. I am looking forward to my future touring.
Finally.
It offers high cost performance in terms of ease of installation, product finish and low cost.
I would recommend this one to anyone who drives the same BMW S1000XR. 。
View detail
Good design and functionality
I was thinking of replacing the Handlebar as a HandlebarUp, but Kit's evaluation I purchased this product because it had very good reviews when I looked at After the installation, I did not feel fatigue even on long distance two-ringing as rated The installation was easy and easy to complete with pictures Foreign Language
View detail
Fits: BMW RnineT, BMW R1250R, BMW R1250GS Adventure, BMW R1200R LC water-cooled, BMW R1200GS LC Liquid Cooling, BMW R1200GS LC Liquid Cooling, BMW R1250GS, BMW R1250RT, BMW R1200RT LC water-cooled, BMW R1250RS, BMW R1200RS LC water-cooled, BMW R1250RT
The wind protection is good
[Was there anything that disappointed you?
Just as I hoped
Do you have any wishes or improvements you would like to make for the Manufacturer?
This is a 2 point stopper for R100 ROADSTER I replaced it with a LeverBracket and stopped the Mirror section as well Please look at the pictures
[Do you have any products to compare it to?
There was nothing special about it
What made you decide to buy?
With Brand's Image, I thought I'd get a product that would be fine
How was your experience with it?
High wind protection, although BMW has a Grip heater on most models
The Handlebar Cover is very hard to put on The coldness of the fingertip has been improved
Matches the parts of the Cowl Department
Was the installation difficult?
It's easy, if you have Torx wrench
【Please tell me the installation point and hang】
In the case of the RS, the Mirror is attached to the Cowl, so the upper part cannot be fixed
I think it's a good idea to order it at the same time as the Type that has a screw hole in the Mirror for the R
I don't know if a two-point stop is a problem, but Hand guard is usually a three-point stop
[Was the Instruction Manual easy to understand?
It is easy to understand, with illustrations and instructions
[Included Parts:were they on?
It also includes Screw, which is not necessary for other cars
[Others]
I bought this for the cold weather, but it's also a good summer bug repellent
It is wind and insect resistant
View detail
It's really nice..
I do not need any special tools for installation work, I think that anyone can do as long as 30 minutes. I was worried about the length of Throttle Cable, Clutch Cable, Brake line, but the only thing that needs adjustment is Clutch Cable, which can be easily adjusted without tools, so there is nothing wrong.
It only increases the height by 25 mm, but the wonder and the benefits are Large, the fatigue feeling of Long touring is considerably reduced.
Originally, with the same height as the G310R Handlebar something that Manufacturer sells is questionable itself, you can drive with a natural Position.
The biggest benefit is Large is improvement of Position when standing. Depending on the height of the OEM, depending on the height of the Rider, I am 182 cm, so it was fairly improved that the honest Handlebar was too low and painful.
It will depend on your physique but it is quite a Recommendation.
View detail
Fits: BMW R1250RT, BMW R1250GS, BMW R1250GS Adventure, BMW R1200GS LC Liquid Cooling, BMW R1200GS LC Liquid Cooling, BMW R1200GS LC Adventure water-cooled
Easy chin
NORMAL is not suitable for Small Patterned Person I am comfortable with 165 Front's holding is different from ss by Front load It seems not to be in Motorcycle It seems not to be related so I wonder if I will be familiar with how to handle it View detail
Fits: BMW R1250RT, BMW R1250GS, BMW R1250GS Adventure, BMW R1200GS LC Liquid Cooling, BMW R1200GS LC Liquid Cooling, BMW R1200GS LC Adventure water-cooled
Position is Large thing!
Position is a Large pattern or I'm not comfortable with it since I started riding ~ I have never had any trouble with Position so much - - - The arms are elongated, arm is against the cutting angle of Handlebar, it is hard to get on with the body going on without going.
Wanderlich Handlebar Up kit seems to be able to transfer Handlebar to 27 mm Back, 38 mm Up.
Wonder Rich has released a number of for BMW products and has also purchased experience, product accuracy and quality will not be a problem!
As Handlebar got high, I was concerned about the Harness, Brake hose relationship, but I was instructed to remove Tie Wrap and fix it as Frame in the manual. Clutch side was not particularly problematic.
View detail