Reviews
Engine braking is smoothed out:??
This is an evolutionary model from KTB3Camshaft Chain CoverBypassKit, only the Adapter was purchased and the Hose and Clip are reused from KTB3.
Although I could not feel the difference between the installed model and the evolved model, I could feel the effect of the original KTB3 that the engine braking was smoother and the engine revving was better from mid-range speed.
View detail
I feel it works.
After installing the engine, I test drove the car and found that the vibration and engine noise, which used to be loud at over 100km/h, did not become bothersome until about 120km/h. The engine noise was not noticeable until about 120km/h.
Smooth behavior when opening and closing Axel
I know it's a bad word, but I honestly felt that Boa Ace had a lot of believers and that it was Brush-bo, but I bought it because I thought I couldn't critique it without trying it on myself.
I was hoping that even if it didn't work, it wouldn't be a Large price and it would be a Dress-up, but I think this will work.
I bought the one with windows, but it seems that they changed the spec. and there is no Laser engraving around the transparent part, and there is no Blue cover of Swage line.
I like the Engine area without the clutter, but I feel that those who want to Appeal need to check.
View detail
Quintessential Boa Ace product.
The installation method was based on YouTube. It was quite difficult, but I managed to install it.
It looks great.
I honestly did not understand the effect as much as I felt it.
I am sure there must be some structural effect.
View detail
I can feel it!
I think this is a very well thought out engine friendly part. View detail
Expensive Parts, but it's Recommends
Bore Ace's products have a high degree of machining accuracy.
There are many attractive products that allow you to experience Performance.
I was hesitant to buy it because of the expensive parts, but I am satisfied with Large.
Below is the in-play after 300?runs.
The response of ?Engine gets better.
The vibration of the ?Engine is softened.
The engine speed rises quickly.
And it's all good.
"Less vibration, faster. That's what I mean
If you're going to be riding SR for a long time, it's a good idea to work on your Engine.
Recommendation Parts.
Installation is not difficult.
No special tools are needed.
(My tools are HOME'S4000 Quantity:It is Set)
The place to pay attention to is the strength of Screw tightening.
If you're unsure, it's best to let Motorcycle Shop do the work for you.
In case you're wondering, my SR is a Type 5.
The company's HeadResponse is also attached to
This is the part where the Engine gets healthy.
The price is affordable and the cost is high, and you can install this one first.
I think it's good. I installed it first.
View detail
Expensive Parts, but it's Recommends
This is an imprint of the SR400FI (Type 5) that I drove for about 50km.
It has a smooth start in 1st gear and can be launched at low rpm without any jerks.
Because of the fast climb in RPMs, I could put it into a phantom 6th gear.
If you're a rider who uses 4000+ rpm on a regular basis, you'll be able to experience it better.
My motorcycle also has their HeadResponse installed, and
The Oil line is a nice addition to the smoothness of the car.
If possible, recommend a combination with HeadResponse.
View detail
If you want
For this price, it would have been perfect if it came with the OEM Copper Washer
HoseManufacturer's notation in blue with white letters on a blue background is also not blue It would have been better if there was an Option to choose the
I don't think Blue is often necessary for individual cars
I think a lot of people care about the color scheme, other than that
View detail
If you want
For this price, I would like to see an OEM Copper Washer included as well
If you can select the color of the SWAGEMark, it's perfect for myMotorcycle! Blue is unnecessary Different specs have a Black base with white text, and it would have been great if this one was added
View detail
EngineCondition is better
It was a change from OEM I felt the stability of the sound and behavior at high speed increased As a layman, I can't determine what is better, but it seems that the behavior is better than OEM I felt in the
As far as looks go, there are more Lines than OEMs, and the part with windows and Oil is visible I like it because it has a custom look and it's cool
There were some places where it was difficult to install, but there were no difficult parts, so it was good It is
View detail
I'd like to stay for a few more rides
I've driven it for 30 years without any major breakdowns, and I wanted to do something Engine friendly I thought about it and after much searching I came across this Oil line
I don't feel a large change in Noise and Torque, but I don't feel a large change in oil temperature The rise has been mild
In addition, I'm writing to you, but next to this, you considered the Boa Ace Oil cooler! But recently, I've been running more slowly, so I thought it was a bit too much Then I saw the Heat Radiation Fin for Oil TankDown tube It remained at
I was really curious about using it and ordered it as an unlisted product When I used it, the oil temperature rose even more gently
Well, Boa Ace is a face-white manufacturer
View detail
You'll see what you can't see
Boa Ace's Twin oil line and simultaneously Oil Assist on the IN side! It actually confirms the flow of Oil, which I had vaguely trusted to be flowing
So what about the EX side?
With that in mind, I installed it on the EXBanjo
I was worried about the damage caused by vibration, but so far I've had no worries about it due to the quality of the build quality
More importantly, it's a relief to see the flow of Oil to the EX side, which is the Week Point
The supply of oil to the EX side was surprisingly slow, perhaps due to the change in hardness of the oil by the temperature
Just figuring this out works!
View detail
Mounting on Yamaha SR 400 FI
During Idling, Acceleration, Constant Speed ??Running, Engine's Machine Noise has definitely become quiet. It took less than about an hour for the installation because there was a place where Banjo's orientation was adjustable and it was narrow and difficult to enter.. I feel good in quality but I'm satisfied with Large, but I think that it was good if the price was a little easier. View detail
The effect is absolutely Large!
Because the reputation of the world is good, I installed it in SR 400 FI
Machine noise decrease - Torque up and the effect is absolutely Large
From Carburetor Vehicles it seems that FI Vehicles is more effective than Large
View detail
Summer measures.
We introduced TWINMeshOil line of Boa Ace in summer measures.
The noise from the Engine head has decreased.
I felt too thin at the OEM line of OEM and it seems there is a possibility that it may break, so I became mentally easier.
After all, very beautiful cutting technique. I thought that it was a flowing stone bore Ace.
For now, there is no problem with hydraulic pressure.
It's a simple Engine tune. You should add SR if you want to make Large.
View detail
SR500 was equipped. The engine machine noise decreased clearly after wearing, and rotation became a smooth. Although there is also a negative opinion to this product in public, since a configuration completely differs from twin line-ization of the
SR500 was equipped.
The engine machine noise decreased clearly after wearing, and rotation became a smooth.
Although there is also a negative opinion to this product in public, since a configuration completely differs from twin line-ization of the other company, there are no worries about the fall of an oil pressure, etc.
Since the oil of the line via which it goes on a head from the crankcase side does not pass along the oil filter, he may think that it is useless, but since 1 times should have gone through the filter if it sees in the whole oil, I also regard these worries as unnecessary.
It may be better to suspect the problem of other parts, when a machine noise carries out, even if it changes into Colet.
Since it is not the parts for lowering oil temperature like an oil cooler, those who are aiming at the effect consider that it is better to purchase an oil cooler.
I think that this product is the goods for compensating the shortage of oil of the circumference of an authentic positive head in order to supply oil to a head immediately at the time of engine start.
It is recommended at those who continue wanting to ride on SR for a long time.
View detail