Reviews
Fits: YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA XSR700, YAMAHA MT-09 SP, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
I am repeating this LED Blinker on my Yamaha car.
[How is it used?
I installed this product on my 2014 YZF-R1 Rearfor Blinker as a LED winker conversion. (I'm considering to convert Front to Built-in)
Was the one you received as per Image?
As a YamahaOEMLED Blinker, it was small in size and true to its image.
Was the installation difficult?
Since I have an external Fender Eliminator on the rear, I used the included RubberSpacer to add bulk, but the body just barely sticks out.
How was your experience with it?
If you install it as it is, one-third of the body is hidden by the width of the License Plate, so I raised it with the included SpacerRubber. It may be possible to consider further raising the height with a few more centimeters of Spacer.
[Included Parts:were they on?
OEMRelay-compatible resistors and Brackets were also included.
[Was there anything that disappointed you?
nothing special
Other items that would be helpful
Opinions and requests to Manufacturer
I would like to sell from Body1pc. as a part, as a supplemental part.
View detail
Fits: YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP, YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
Installed on a Racer 900GT
I installed it on a 2020 Toracer 900GT.
I purchased the LEDs because other manufacturers have been using LEDs for quite some time now, but Yamaha is still using bulbs at this time.
The installation is a little troublesome. The front panel is double-layered where the blinker is attached, so the inner panel is screwedQuantity:Quantity 2pc and special clasps:2pc. The Rear side is easier to work with if you remove the license plate bracket. And Quantity:Pair (for Left and Right) I put the resistor inside the Seat Cowl on the Rear side, but I think it is better to avoid the plastic part because of the heat generated. I did not want to cut the OEM wiring, so I bought a Conversion Connector and installed it, so there was no wiring. I am happy with the way the light shines differently than the OEM.
View detail
Fits: YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA XSR700, YAMAHA MT-09 SP, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
I wish they had put this on from the start.
I was feeling frustrated by the fact that the XSR700 2022MODEL was an LED Blinker (lol).
Originally, we were dissatisfied with the shape of the blinker, which was blingy, so we decided to replace it.
Looks Parenthesis better as I expected.
I had it installed at the shop and it took quite a while.
View detail
Fits: YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA XSR700, YAMAHA MT-09 SP, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
Mounted on MT-07
It was installed on MT-07. It came with a resistor, but I was concerned that it would get very hot, so I stopped using the resistor and used the Led Blinker Relay. I am very satisfied with the brightness when I turn it on.
After about 6 years of use, one of the LED lights went out.
There was a symptom that the inside of the Lens fogged up a little when driving in Large rain.
(Although the cloudiness disappeared after one night.)
View detail
Fits: YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP, YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
No problem at all with OEM Product only
I bought a Carbon Style,
Texture is the best.
It works without problems with the attached Relay. Relay itself is not as big as it is told. In my case I put it in Space under Rear Sets.
To good things, Quantity : 1 Set of 4pcs. I would like you to lower the price and sell it.
View detail
Fits: YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP, YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
The price is expensive - - -
Headlight, Tail lamp is a LED bulb, but it was only a light bulb, so I was concerned despite being invisible while driving, so I replaced it because of my mental health.
I could work with Electric Works Pliers and Spanner, Socket wrench, Hexagon without feeling difficulties.
In Front Side Panel's lining installation method, Washer with nails is bite in three places and I did not know how to officially remove this Washer, push up a little by little in the direction to remove the nail with a thinner Driver ahead Did.
Washer with detached nails flattened the nails with Pliers and used again, but the problem was not felt in particular.
Resistance is also attached to this product, and 4 places (Quantity : 2 Set) When exchanging Quantity : 2pc. Use Set resistance.
Our tarcer has attached resistance to Rear blinker but in order to fit in the gap under Seat you need to warrange longer while tentatively assembling using Wiring of OEM's Blinker. If there is something to be aware of in installation it is about this.
After installation, we are satisfied with OEM that Blinker got smaller and fearless and became fearless face. I can not see it while I am on the train - - -
View detail
Fits: YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA XSR700, YAMAHA MT-09 SP, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
I think it's good.
I installed it in MT-25 of YAMAHA. Because Front was too long, it cuts a little and connects. Rear lacked Length, purchased separately Bullet Terminal and Wiring and extended. Resistance to Front LeftRight or RearQuantity : Pair (for Left and Right) I have to attach to. Just wrote that resistance has sometimes heat, Rear side is stored under Seat and Wiring is dense, so select Front side. However, the Front side did not have the space and had a bit of hardship.
After installation it is moving normally. The appearance is smart. Just wish Cost will fall a little more. I think that it can not be helped because it is an OEM product. Comprehensively Large satisfied.
View detail
Fits: YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA XSR700, YAMAHA MT-09 SP, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
The shape is also good as Parenthesis is good!
If you thought that the shape is also good as Parenthesis well analogous products have been commercialized from Wa Big! This one is cheaper - - -. The feeling of having felt early - - -. I wish I had goodly scrutinized it. View detail
Fits: YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP, YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
I liked it because the design was high though it was expensive
I attached it to MT-09 TRACER. Although it was expensive at the time of purchase of the vehicle, I had to wait for purchase, but other products etc.. While I was looking at, I thought that this was a good purchase. Installation was not so difficult, but it is MinusPoint that I must process Wiring ~. I hope I can make it a little cheaper! View detail
Fits: YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP, YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
Used for Custom
I like the appearance very much.
I attached it to MT - 09A, but the resistance module which prevents High flasher is quite Large, and it was hard for me to put it together with Wiring at the time of wearing. (Because MT-09 is so narrow - - - )
After all, I installed a relay for LED at a later date and removed the resistance module.
I wish Relay was sold separately.
View detail
Fits: YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP, YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
Wiringetc. Trying to put it in SMART will struggle
Because Rear's Blinker was replaced with Active's License Plate Holder integrated type, in conjunction with this, we also replaced the Front side with Y's Gear's LED Blinker.
?Good point?
- Although I took it for Small, the LED is bright and outstanding visibility
- Attachment of Yamahafor Vehicle egg type comes with attachment of Body easy
- Good design that does not astute
?This is not good?
- Despite OEMOption of Yamaha cars handled as Universal Product
- So Wiring is also made on the premise of Main harness cutting → Bullet Terminal processing
- Ceramic resistance too much
In my MT - 09, already DAYTONA 's ICBlinker relay (69571) Since we were using it, we did not use Ceramic resistance.
However, if you use Ceramic resistance as OEM's Relay, Space is hopelessly narrow on the Front side of MT-09 and I think that it will be very difficult if you try to put it in SMART for ease of later maintenance.
There is also a danger of heat generation of Ceramic resistance and there is no space, so we recommend that you exchange it to LED-compatible Relay if you are installing it on the front side of MT-09.
I felt that I could not believe it as soon as I bought it and opened it and checked the contents.
Because it was Universal Product of Bullet Terminal connection premise despite Yamaha's OEMOption.
Attachment to be attached to the car body is also included, so I wanted at least that the conversion Coupler adapted to the car body of Yamaha was included as well.
Although it is still ahead of the story, considering selling the car body, it is inevitable to change Main harness.
So I am buying a 250 type CN Female 2 - pole Coupler at the mail order site selling Couplers related to cars, and Bolt - onSpec. I am connecting with.
Electric Works Pliers 1 pc If you do not think about anything, you can exchange even an amateur with knowledge of the extent that you have easily examined with Net if you have it, but you want to devise another thing after thinking about it later.
View detail
Fits: YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP, YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
I replaced my front blinker to YSGEAR(YAMAHA) LED blinker.It is quite small compared to the original product.I was worried about its light quantity at first, but it seems it is light enough when you see it from its front. Cars can detect you all r
I replaced my front blinker to YSGEAR(YAMAHA) LED blinker.
It is quite small compared to the original product.
I was worried about its light quantity at first, but it seems it is light enough when you see it from its front. Cars can detect you all right. Still, I noticed that its visibility level drops when the angle changes a bit. I doubt it could be seen from a car whose driver's seat is at a high position.
It comes with a bracket to fill the resistance hole or the cowl side hole. So all you need is a conversion cable to switch from the OEM connector (I used DAYTONA one).
The front side installation is easy.
It said to be careful because the resistance was going to be hot. So I used a cable tie to float it inside the cowl and fixed it, while making sure not to let it touch other cables.
Though the blinker and hazard system seems to be working all right, I will place 4 stars for it was a little smaller than what I had expected.
View detail