Reviews
Mounting.
Cannot be installed as is. (Quantity:Pair (for Left and Right) The square hole for the bottom hook was too small, so I had to cut it out and install it. The checkerboard pattern also looks smaller than in the picture. I am a little disappointed because I ordered and waited for a long time. View detail
For Radiator protection, these are the best
Installed in addition to the Fender extension on the front.
Maybe this will make Radiator Large sturdy...surely.
Mounting is done with the Quantity:Pair (for Left and Right) Simply remove and friend-tighten the Radiator cover of the
The only regret is that it is only available in Silver. since the Radiator was also in Black on a Black car body, I painted it with a Spray can to match the color.
Large sturdy, even if appropriate, for areas that are not well visible.
View detail
It is as good as expected.
Fit the Radiator exactly as shown in the photo.
I think it is quite decided.
It would be helpful if it is mentioned in the Instruction Manual.
View detail
I think it's best.
Although there are many manufacturers of Core Guards, you don't have to worry about the manufacturer of the exhaust system you are installing. Installation is easy. View detail
I like the fine mesh
I installed it on a CB1300sf2019MODEL
The first item that was shipped was misaligned with the hole on the side that secures it to the Radiator, so we had to replace it and I got it The replacement was also slightly off, but I'm glad I was able to put it on as long as I pushed it in
The part where the core guard touches the Radiator is the Small side of both Sides Since it was next to the Bolt, I put the attached Skimmer Cushion on it
As for the fitment, there is moderate Tension and driving wind etc., on the Radiator side It doesn't seem to be pushed in
If I wanted to, I would like to see the holes on the side of the Radiator to be moved back a bit It's just a matter of shaving it by yourself
I haven't run it yet, but it's finer than the OEM's governing Guard, and the Bug Attacks It seems to be expected to prevent
View detail
Used for ZrXZrX 1200 DAEG. The appearance is very Beauty.
The angle of the lower part of Right Side 's Cover was too wide and could not be installed because it did not match the angle of Radiator side at all.
We had Manufacturer remanufactured to have it replaced but the item we arrived was a little better, but if you could forcibly install it, you could install it but there is a possibility of it being broken while using it.
Cancellation was also possible, but since it is troublesome, I heated it with Heat gun and fixed the angle of the part and installed it.
Manufacturer's inspection results are "Individual difference" I mean that ? ? ?.
Also, since the square hole on the bottom side of Cover is Small, it does not add to the hook on the car body side. This is done by deleting with File.
It is so expensive Parts, so I want you to raise the accuracy a little more.
View detail
It is difficult to put on!
Rubber packing something like that. I'd like to get one new Packing. You had better put on Shop. View detail
Almost in appearance
When you tried whatever you were Customing when exchanging.
I installed Bolt as Gold.
It will be nearly 10 years, but there is nothing wrong. "
View detail
It must be a reassurance fee - - -
I purchased it because the stepping stone to the Radiator was uneasy.
Originally not being equipped on the Manufacturer side,
I think that the stepping stone to the Radiator itself is stochastically low, but I am satisfied with a sense of coolness and security.
But I think the price is expensive.
In the case of the preceding vehicle I was wearing something my own made at about 1,500 yen. Even if you look at the materials and features, it is high even at about half price.
View detail
To the mounting arrangement of a Radiator at 400R attached to NINJA400R Those with two kind, In the description of the Manufacturer, only the mounting arrangement corresponding to the latest thing of 400R was written, but when the Manuf
To the mounting arrangement of a Radiator at
400R attached to NINJA400R Those with two kind,
In the description of the Manufacturer, only the mounting arrangement corresponding to the latest thing of 400R was written, but when the
Manufacturer with a Bolt required for an initial MODEL etc. was asked, sent Bolts required for the next day, but.
* since it was not investigated in advance is three.
Although the Sponge for the thing of the other company to already have corresponded [ which buries the crevice between
Core guard and a Radiator since like ] was attached,
Although I bought it by Sale + Point + Monitor this time [
] which was not worried,
the high net of the
STAINLESS STEEL -- This price ... it is fluent...
attachment will be attached if there are an easy - hezagonal wrench etc. -- it is attached even if it does not remove the
Cowl --
--
-- although a Recommendation can be carried out once ......
View detail
He bought the product made from webike Monitor FRP this time. Since he wanted to prevent steam which rises from Radiators, such as a day of rain, although it was if there is which the Manufacturer attached to the NORMAL Motorcycle,
He bought the product made from webike Monitor
FRP this time.
Since he wanted to prevent
steam which rises from Radiators, such as a day of
rain, although it was if there is which the
Manufacturer attached to the NORMAL Motorcycle, it purchased.
since the object for
Racers could be sufficient as it although making
was solid -- a description --
-- it wanted -- since it comes out, and it is peevish and grows into reference of attachment.
I would like to expect a future effect.
View detail
It attaches to GSX1400. If a raw material is seen by the eye, it will think that the cut portion ? of a hole is somewhat coarse, but I think that it is quite good for a dress-up up at that which also says a design. However, is a raw material a min
It attaches to GSX1400.
If a raw material is seen by the eye, it will think that the cut portion ? of a hole is somewhat coarse, but I think that it is quite good for a dress-up up at that which also says a design.
However, is a raw material a minus in the point of it being comparatively soft and being easy to rust with bending immediately as unexpected?
Although I think that it is comparatively [ expensive ], in the design, it is pleasing.
View detail