- หน้าแรก
- รุ่น
- HONDA 51 - 125cc
- ZOOMER-X
- อะไหล่แต่ง
- ระบบไฟมอเตอร์ไซค์
- ชุดไฟส่องสว่าง
- หลอดไฟหน้า LED
- PROTEC
- PROTEC: ชุดหลอดไฟหน้า LB7-ZX LED
รายละเอียดสินค้า
รายละเอียดสินค้าด้านล่างนี้ใช้โปรแกรมแปลอัตโนมัติโดย Google Translate
แสดงต้นฉบับ
คุณสมบัติ
ประเภท : ค่า PH7ชั่วโมงการทำงานโดยประมาณ : 60 นาที
อุณหภูมิสี : 6000 พัน
แรงดันไฟฟ้า : ใช้ 12V AC-DC
ชุดหลอดไฟ 2 ดวง
การใช้พลังงาน : 20W (ไฮบีม) / 20w (โลบีม)
ใช้หลอดไฟ USA CREE X XL-P LED
Type: PH7
Estimated Working Hours: 60mins.
Color Temperature: 6000K
Rating Voltage: 12V AC-DC Used
2-lamp Kit
Power Consumption: 20W (Hi Beam)/20W (Lo Beam)
It uses USA CREE X Lamp XL-P LED.
รายละเอียดคำถาม
ซึ่งใช้ในพัดลมระบายความร้อนของหม้อน้ำ
Specially designed for reliable Hi/Lo illumination and AC lighting for vehicle-side electrical systems!
With a 1-year manufacturer's warranty!
Waterproof Cooling Fan Cyclone System!
Waterproof cooling fan for efficient heat transfer!
ZOOMER-X Exclusive design valve
Hi/Lo switching light distribution is reliably illuminated!
Two 10W x 2 LED chips each for high and low voltage
Flat fan stays are used.
The controller unit is attached to the combination brake stays in the front cowl
Resistors to control the voltage rise (specially designed)
The heat generated by the LEDs can be efficiently dissipated so that they always light up at full power!
Although LEDs are characterized by a very high conversion efficiency (i.e., the efficiency of converting input power into visible light [electromagnetic waves at visible wavelengths that can be seen by the human eye]), even so, if the input power is assumed to be 100%, more than 70% of the input power will be converted into heat.. The Cyclone LED series is a combination of three components:solid aluminum, heat sink, and waterproof cooling fan, which effectively dissipates heat and enables full power operation at all times!
Thermal management is a must for heat-sensitive LEDs. If this heat cannot be dissipated efficiently, you will have no choice but to reduce the power from the start of the lighting process or to reduce the power from the middle of the lighting process.. In other words, if you don't have good thermal protection, you won't be able to use the full potential of LEDs..
Highly durable waterproof fan is used!
In the Cyclone LED series, the fan plays an important role in efficiently cooling the heat generated by the high power LEDs.. The fans used in general electronic equipment are of the metal-supported type, which have low durability and are not suitable for motorcycles.. The Cyclone LED series uses biaxial ball bearing type" bearings
With a 1-year manufacturer's warranty!
Waterproof Cooling Fan Cyclone System!
Waterproof cooling fan for efficient heat transfer!
ZOOMER-X Exclusive design valve
Hi/Lo switching light distribution is reliably illuminated!
Two 10W x 2 LED chips each for high and low voltage
Flat fan stays are used.
The controller unit is attached to the combination brake stays in the front cowl
Resistors to control the voltage rise (specially designed)
The heat generated by the LEDs can be efficiently dissipated so that they always light up at full power!
Although LEDs are characterized by a very high conversion efficiency (i.e., the efficiency of converting input power into visible light [electromagnetic waves at visible wavelengths that can be seen by the human eye]), even so, if the input power is assumed to be 100%, more than 70% of the input power will be converted into heat.. The Cyclone LED series is a combination of three components:solid aluminum, heat sink, and waterproof cooling fan, which effectively dissipates heat and enables full power operation at all times!
Thermal management is a must for heat-sensitive LEDs. If this heat cannot be dissipated efficiently, you will have no choice but to reduce the power from the start of the lighting process or to reduce the power from the middle of the lighting process.. In other words, if you don't have good thermal protection, you won't be able to use the full potential of LEDs..
Highly durable waterproof fan is used!
In the Cyclone LED series, the fan plays an important role in efficiently cooling the heat generated by the high power LEDs.. The fans used in general electronic equipment are of the metal-supported type, which have low durability and are not suitable for motorcycles.. The Cyclone LED series uses biaxial ball bearing type" bearings
คำอธิบาย
คำเตือน
but it has passed the 2-hour seismic test of 20G! Only Protech is the only motorcycle LED bulb with waterproof & durable fan..Safe and reliable products for vehicle inspection!
The maximum luminous intensity easily passes 15.000 candelas
*Specially designed valve is not compatible with universal PH7 type.
*Image 2 shows the Hi beam on.
*Image 3 shows the Lo beam on.
*All vehicles that have been tested by Protec are stock.There is a possibility that a problem may occur if the vehicle is equipped with aftermarket parts other than stock parts.
*In the case of a 2-light motorcycle, 2 sets are required for installation on both sides (2-light kit [part number: Except for vehicles that conform with [65005, etc.]).
*Please refer to the service manual of your motorcycle to confirm the respective wiring before installation.
[warning]
*Install the product correctly according to the instruction manual.Improper installation may result in fire or equipment damage.
*Before installation, be sure to disconnect the terminal cord on the minus side of the battery and confirm that the key is OFF.
*Please do not touch or get the LED chip dirty.Dirt can cause the LED chip to burn due to heat being built-up.
*Please handle this product with care as it is a precision instrument.Do not drop the product or pull the wires forcibly.Improper handling may cause malfunction, injury, burns, or serious accidents that may result in death.In addition, sparks, poor insulation, or short-circuiting may cause a failure of the product or a fire in the vehicle.
*Do not disassemble or modify this product in any way.Products that have been disassembled or modified are not covered by warranty.
*Do not look directly at the LED light when it is on.It can cause visual impairment.
*Do not splash water on the lens while the light is on or immediately after it is turned off.Sudden temperature change may cause damage to the lens or LED bulb.In addition, please do not touch the LED bulb itself, the heat sink behind it, and the controller unit because they get to the high temperature.
[Notes]
*This product is only for 12v DC minus common.Be sure to use DC12V as the power source for wiring.
*This product is not compatible with AC headlights, which are often used in small displacement vehicles, so please do not install this product.
*The negative side of the headlight wiring is the same for both Hi and Lo beam.Not compatible with vehicles with positive common headlights.
*As to minibike kits
The kit for minibikes can be used with 12V DC, AC, battery-less(*1), minus common(*2), plus common(*3) motorcycles.
(*1. Please use ADC-200 (65016) Battery-less Kit (sold separately) when you use it on a vehicle with the battery removed.)
(*2. "Minus common" refers to the type where the minus side of the headlight wiring is common to both the Hi beam side and the Lo beam side.)
(*3. "Plus common headlight" refers to the type in which the positive side of the headlight wiring is common to both the Hi-beam and Lo-beam sides.)
*This product is for motorcycles only, so cannot be used on four-wheeled vehicles.
*Do not cover with paper or cloth and do not light near flammable materials.Failure to do so may result in fire or abnormal heating.Also, do not light near flammable items such as flammable spray, thinner, etc. or items that may ignite.
*Do not install to the headlight with the light on.Failure to do so may result in malfunction or burns.
*This product is waterproof for daily life, but it is not completely waterproof.Wrap the coupler coming out of the controller unit with vinyl tape or self-bonding tape, or use caulking agent to waterproof it.Avoid wetting the product with more water than necessary.
*When washing a vehicle with a high pressure washer, please do not let the high pressure wash directly hit this product.
*Please do not drop the LED bulb or controller unit, or give it a strong shock.It not only causes breakage, deterioration of performance and shortening of service life, but also causes injury.
*Be sure to apply the included silicone grease when assembling the LED bulb.Please refer to this manual for details.
*Do not touch the LED chip when it is off or on.
*Do not cover up the waterproof cooling fan.Make sure that there is enough space behind the fan for the sucked air to flow.
*The waterproof cooling fan has a specific orientation for installation.Be sure to install with the silver round seal facing outward.
*Use a thread locker to prevent loosening of the threaded part.Periodic retightening is also recommended.
*Installation requires expertise and skill.Please have it done at a designated maintenance facility with skilled mechanics.
*Please adjust the optical axis before use.It may obstruct the view of oncoming vehicles and cause traffic accidents.
*PROTEC is not responsible for any damage or accident caused by the use of this product.Protec will not be responsible for any labor charges or other costs incurred during repair.
*If you feel any abnormality during installation or use, please contact PROTEC Service Department.
After installing the product, be sure to adjust the optical axis using an inspection machine that is compatible with LED (new light source).PROTEC is not responsible for any dirt or clouding of the light lens, scratches, peeling of the reflector plating inside the light, or poor maintenance due to poor optical axis adjustment or age-related deterioration.
ลิ้งค์หน้ารุ่นรถ
ทบทวน
0.0
/ 5
(0 ทบทวน)
สินค้าที่ดูก่อนหน้า
มีสินค้าในสต๊อกพร้อมจัดส่ง
สินค้าแนะนำ
สินค้าที่เกี่ยวข้อง
สินค้าแนะนำ
สินค้าที่ดูล่าสุด
ใช้คูปอง
รูปภาพรีวิว
Review detail
/