Please login to check coupons
Product Description
Universal
Specification
Quantity: 1
Description
●A set of silencer bands and rubbers required when replacing the exhaust.
●Made of 1.2mm thick stainless steel.Two ribs are provided in the bending section to ensure sufficient strength.
●M8 x 25 Stainless steel cap bolt with flange included
●M8 stainless steel washer and M8 locknut included
●Please make sure that there is no play in the silencer.If the silencer is too big for the band, please use Kitaco's aluminum spacer collar to adjust.
Note
K-CON general information page
Repair silencer band rubber here
/ 5
I bought a silencer band from KITACO because I changed from Earls Gear's silencerφ100 to Universal Product's silencerφ80.:It looks very beautiful and sturdy with Stainless Steel, but I had trouble fixing it because the diameter of the silencer is 1cm lower than the original one. I would be happy if there was a type that could adjust the length of the mounting part as well as the type of φ, but I guess it would be difficult considering the cost. (Especially, it is difficult to extend the length by 1 to 2 cm because you cannot put a bracket between them.) The silencer was too large, and when I put in the rubber sheet, the phi; became a little too small to reach, and I put in the 6mm spacer and installed it. By the way, Material:Although Aluminum is availableMaterial:Titanium is expensive and unprofitable, isn't it? If possible, is it possible to get a one-off price at Netetc.?It is very helpful to have a manufacturer like KITACO who provides various universal products and parts at a good price.Please keep up the good work. I'm rooting for you. View detail
Vino (SA10J) I used it toThe exhaust system of N company is installed The exhaust system of Silencer fixed by agingThe Rivet was loose and I used the Hand Riveter to re-hit itI'm worried about it, so I bought a Silencer band to fix it to the body of the carThe Silencer band and bracket for the body are made by the T CompanyPut it between the Silencer and the attached HexagonalBolt&NutIt's only 13mm, but Nut is 13mm, so you need to be careful about the tool you useThis is where you want them to use the 14mm Nut that is commonly used for MotorcyclesAlign the Bracket with the HexagonalBolt and tighten up the HexagonalBolt to avoid wobbleFirmly fixedThe construction of the bending part is very solid, and the Material:Stainless Steel, so it will rustIt's good to have no worriesI like it because it has excellent cost performance at a reasonable price View detail
When installed in Silencer of YOSHIMURA, about 10? Spacer is required. I think that it is because the outer diameter becomes smaller with the thickness of the Elastic band, but it was unexpected. I caught a friendly Nut and managed to install it. Although it is a little narrow compared to YOSHIMURABand, the glow of Stainless Steel is about the same, so I think it is a good item to go from Cost performance. View detail
Because there is no Silencer Band, I purchased this product, but it was a failure. I measured the number of piesThe Band part floated and it passed through it.For the adjustment, we inserted a Rubber between Rubber and it went well. View detail
If you use KIJIMA 's AluminumBand, it will be packed up in about a monthSo I was in trouble and made this.In Stainless Steel it was inexpensive that the deciding factor of purchase.The thing is also the wall thickness (At least from Aluminum) It is robust..It will not break.Just remove the Rubber board and set it up with Aluminum silencer and galvanize and Silencer sideIt became textured. If it is Stainless Steel it can be as it is,If the other party is a heterogeneous Gold genus, it is better to use the attached Rubber board without fail. View detail