จุกอุดปลายแฮนด์ G Type

  • รหัสสินค้า: 000HZCJ009Z

    ฿5,005

    คะแนนวีไบค์: +50 pt

    ข้อมูลการจัดส่ง

    • ระบบกำลังคำนวณวันที่พร้อมจัดส่ง.....
    ถึง ThaiLand
    เปลี่ยน
    เลือกที่อยู่:
    ThaiLand
    ค่าจัดส่ง ฿100

    จำนวน

    สินค้าแท้ 100% รับประกัน 7 วัน รับเงินคืนฟรี ราคาสุทธิ

    รายละเอียดสินค้า

    รายละเอียดสินค้าด้านล่างนี้ใช้โปรแกรมแปลอัตโนมัติโดย Google Translate แสดงต้นฉบับ

    คุณสมบัติ

    [Material] Stainless Steel
    [Weight] One Side 112g
    [Corresponding ] เส้นผ่านศูนย์กลางด้านในแฮนด์บาร์ Φ16mm

    รายละเอียดคำถาม

    แฮนด์จับทำจากสแตนเลสและช่วยลดแรงสั่นสะเทือนของแฮนด์จับ
    ดีไซน์เรียบง่ายแต่ต้องระมัดระวังน้ำหนัก
    ขนาดเส้นผ่านศูนย์กลางภายในแฮนด์บาร์ Φ16 มม. ติดตั้งในชุดแฮนด์บาร์ K-FACTORY

    ทบทวน

    3.0

    / 5

    (1 ทบทวน)

    0

    0

    1

    0

    0

    กรอง:
    เลือกดูจาก:

    Fits their Pipe Handlebar, requires Small modification.

    24 Sep 2021
    3.0
    This is the KFACTORY Pipe Handlebar that I replaced the other day, and the included Material:The DURACON Bar End was too light, and it vibrated fiercely when I turned more than 8000rpm. when I used OEM Handlebar, it vibrated at 4000rpm, but it disappeared. I bought the G Type because I couldn't install the F Type Bar End that I had before. I bought the G Type because I couldn't install the F Type Bar End because I changed the Handlebar.
    When I observed it well, there was a step around 3cm inside of Handlebar, and the inside diameter became small. 16φ inside diameter should be, but actually it was about 15.5φ. Well, I was troubled for a moment what to do, but because it seemed to be able to enter if I shaved Rubber Bush, I processed one turn Small with sandpaper of No.200. After that, I struck the Bar End forcibly with a plastic hammer, pushed it in, tightened the Bolt, and finished. Isn't it possible to remove it any more? I was able to fix it so Firmly. I tried to test drive it immediately, but the fierce vibration at high rpm almost disappeared, but the fine vibration remained. There seems to be no vibration at a specific RPM. I had some numbness in my hand when I drove for a long time, so it is difficult to make a perfect vibration countermeasure. But this size and One Side 7,000 yen......honestly Quantity:2pc. Isn't it about 7,000 yen for Set?
    ดูรายละเอียด
    นี่คือแฮนด์บาร์ของ KFACTORY ที่ฉันเปลี่ยนเมื่อวันก่อน และวัสดุที่รวมไว้:ปลายแฮนด์ DURACON เบาเกินไป และมันสั่นสะเทือนอย่างรุนแรงเมื่อฉันหมุนรอบมากกว่า 8000 รอบต่อนาที เมื่อฉันใช้ OEM Handlebar มันสั่นที่ 4000 รอบต่อนาที แต่มันหายไป ฉันซื้อ G Type เพราะฉันไม่สามารถติดตั้ง F Type Bar End ที่เคยมีมาก่อน ฉันซื้อ G Type เพราะฉันไม่สามารถติดตั้ง F Type Bar End ได้เพราะฉันเปลี่ยน Handlebar
    เมื่อฉันสังเกตให้ดี ด้านในของแฮนด์จับประมาณ 3 ซม. และเส้นผ่านศูนย์กลางด้านในก็เล็กลง เส้นผ่านศูนย์กลางภายในควรจะเป็น 16φ แต่จริงๆ แล้วมันคือประมาณ 15.5φ ฉันรู้สึกเป็นกังวลอยู่ครู่หนึ่งว่าควรทำอย่างไร แต่เนื่องจากดูเหมือนว่าจะสามารถเข้าไปได้ ถ้าฉันโกน Rubber Bush ฉันจึงดำเนินการเทิร์นเล็กด้วยกระดาษทรายเบอร์ 200 หลังจากนั้น ฉันใช้ค้อนพลาสติกกระแทกที่ปลายบาร์ ดันเข้าไป ขันโบลท์ให้แน่น และทำเสร็จแล้ว เป็นไปไม่ได้ที่จะลบอีกต่อไปหรือไม่? ฉันสามารถแก้ไขได้อย่างแน่นหนา ฉันพยายามทดลองขับทันที แต่การสั่นสะเทือนที่รุนแรงที่รอบต่อนาทีสูงเกือบจะหายไป แต่การสั่นสะเทือนที่ละเอียดยังคงอยู่ ดูเหมือนว่าจะไม่มีการสั่นสะเทือนที่ RPM เฉพาะ ฉันมีอาการชาอยู่ในมือเมื่อขับรถเป็นเวลานาน ดังนั้นจึงเป็นการยากที่จะแก้ไขการสั่นสะท้านที่สมบูรณ์แบบ แต่ขนาดนี้และด้านเดียว 7,000 เยน......ขอบอกตรงๆว่าจำนวน:2ชิ้น. ชุดละ 7,000 เยนไม่ใช่เหรอ
    ดูรายละเอียด
    แสดงที่มา

    สินค้าที่ดูก่อนหน้า

    มีสินค้าในสต๊อกพร้อมจัดส่ง

    สินค้าแนะนำ

    สินค้าที่เกี่ยวข้อง

    สินค้าแนะนำ

    สินค้าที่ดูล่าสุด

    New Custom Article

    ดูทั้งหมด