- หน้าแรก
- ความเห็นต่อสินค้า
- เครื่องมือ
- เครื่องมือไฟฟ้า
- ฉันใช้มันสำหรับก... (SK11: Off-set PRO Stainless Steel Ironworker)
【SK11】Off-set PRO Stainless Steel Ironworker Review
I used it for Chain cut!
[How is it used?
Currently used for Chain cut.
How was your experience with it?
Although I was looking for an Offset that can be used for Chain cut, I bought it with the feeling that the performance was good and the price was comparatively cheap because I did not understand this kind of consumable until I used it.
I only use it for chain cut, but it grinds well. It took me about 5 minutes to grind one part with the Large.
The wear is normal, not extremely worn out, and it will work for the foreseeable future.
How did it compare to other products?
It is a domestic Manufacturer and the price was relatively cheap.
[Points to note]
For safety reasons, it is recommended to run a test run for about 60 seconds before use to make sure there are no abnormalities.
If you keep the contact angle of 15-30° in mind, you won't get bounced.
Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer
ฉันใช้มันสำหรับการตัดโซ่!
[ใช้ยังไง?
ปัจจุบันใช้สำหรับตัดโซ่
ประสบการณ์ของคุณกับมันเป็นอย่างไร?
แม้ว่าฉันจะมองหา Offset ที่ใช้สำหรับการตัดแบบ Chain ได้ แต่ฉันซื้อมันด้วยความรู้สึกว่าประสิทธิภาพดีและราคาค่อนข้างถูกเพราะฉันไม่เข้าใจวัสดุสิ้นเปลืองประเภทนี้จนกระทั่งฉันใช้มัน
ฉันใช้มันสำหรับการตัดโซ่ แต่มันบดได้ดี ฉันใช้เวลาประมาณ 5 นาทีในการบดส่วนหนึ่งด้วยขนาดใหญ่
การสึกหรอเป็นเรื่องปกติ ไม่ทรุดโทรมมาก และจะใช้งานได้ในอนาคตอันใกล้
เปรียบเทียบกับผลิตภัณฑ์อื่น ๆ ได้อย่างไร?
เป็นผู้ผลิตในประเทศและราคาค่อนข้างถูก
[จุดที่ควรทราบ]
เพื่อความปลอดภัย ขอแนะนำให้รันการทดสอบเป็นเวลาประมาณ 60 วินาทีก่อนใช้งานเพื่อให้แน่ใจว่าไม่มีสิ่งผิดปกติเกิดขึ้น
หากคุณรักษามุมสัมผัสที่ 15-30° ไว้ คุณจะไม่เด้งกลับ
รายการอื่นๆ ที่จะเป็นประโยชน์
มีชิ้นส่วนที่รวมอยู่หรือไม่:/ รายการที่ควรซื้อร่วมกัน/ความคิดเห็นและคำขอไปยังผู้ผลิต