- หน้าแรก
- ความเห็นต่อสินค้า
- อะไหล่แต่ง
- เบรค
- การ์ดปั้มบน
- ติดตั้งบน Z400 แม่ปั... (SNIPER: Master cylinder guard)
【SNIPER】Master cylinder guard Review
ใช้กับรุ่นรถ: KAWASAKI NINJA250, KAWASAKI NINJA400, KAWASAKI Z250, KAWASAKI Z400
Mounted on Z400Front brakes master
[How is it used?
Model used:Z400
Driving in Touring Main.
About 2 weeks after installation.
Was the one you received as per Image?
The red coloring of the Anodized is also good, and I felt it would be good to increase the number of red Anodized areas on the body.
Was the installation difficult?
To install, remove the Fluid Tank Cap Mounting Bolt and install this product without removing the Fluid Tank Cap, using the long stainless steel bolt provided.
The work itself is simple, but since the bolt on the Fluid Tank Cap has a +Screw, it must be removed using a good precision driver.
Note that +Screw should be loosened with a pushing force of 6 and a turning force of 4, rather than with full force in turning, to avoid licking the screw head.
How was your experience with it?
Although it has only been installed for a short time, the coloration of the Anodized is satisfactory and has improved the appearance.
Since this product is a Guard, there seems to be no doubt that it will protect the MASTER well in terms of shape, although it is for insurance purposes in the event of a fall.
Although it can improve the appearance, Z400 can recommenendation to those who compete in Gymkhana competitions with Normal master.
High SIDE may not work, but SlipDown would provide protection.
The holding of Anodized will be verified in the future.
The edge processing was a little lax in some areas, and it was a little unfortunate that the anodized material was a little peeled off in these areas.
[Included Parts:were they on?
Stainless bolt
[Was there anything that disappointed you?
Edge treatment
Point and hang of installation
Loosening of Fluid Tank Cap+Screw
Pushing force 6, Turning force 4
Installation of the included Stainless bolt
To avoid seizure and other troubles whenever possible, it is recommended to use Anti-seeds, CopperThread, Molybdenum grease, and Molybdenum anti-seizure agent for tightening.
Note that a Hexagonal Wrench should be used for installation.
ติดตั้งบน Z400 แม่ปั๊มเบรคหน้า
[ใช้ยังไง?
รุ่นที่ใช้:Z400
การขับรถในทัวริ่งเมน
หลังการติดตั้งประมาณ 2 สัปดาห์
เป็นคนที่คุณได้รับตามภาพหรือไม่?
สีแดงของอะโนไดซ์ก็ใช้ได้ดีเช่นกัน และฉันรู้สึกว่าคงจะดีที่จะเพิ่มจำนวนบริเวณที่เป็นสีแดงบนร่างกาย
การติดตั้งทำได้ยากหรือไม่?
ในการติดตั้ง ให้ถอดสลักเกลียวยึดฝาปิดถังน้ำมันออก และติดตั้งผลิตภัณฑ์นี้โดยไม่ต้องถอดฝาครอบถังน้ำมันออก โดยใช้สลักเกลียวสแตนเลสแบบยาวที่ให้มา
การทำงานนั้นเรียบง่าย แต่เนื่องจากสลักเกลียวบนฝาปิดถังน้ำมันมี +สกรู จึงต้องถอดออกโดยใช้ไดรเวอร์ที่มีความแม่นยำดี
โปรดทราบว่า +สกรูควรคลายด้วยแรงผลัก 6 และแรงหมุน 4 แทนที่จะใช้แรงเต็มที่ในการเลี้ยว เพื่อหลีกเลี่ยงไม่ให้เกิดการเลียหัวสกรู
ประสบการณ์ของคุณกับมันเป็นอย่างไร?
แม้ว่าจะได้รับการติดตั้งเพียงช่วงเวลาสั้นๆ แต่สีของ Anodized ก็น่าพอใจและปรับปรุงรูปลักษณ์ให้ดีขึ้น
เนื่องจากผลิตภัณฑ์นี้เป็น Guard จึงไม่ต้องสงสัยเลยว่าจะปกป้อง MASTER ได้ดีในแง่ของรูปทรง แม้ว่าจะใช้เพื่อการประกันในกรณีที่หกล้มก็ตาม
แม้ว่าจะสามารถปรับปรุงรูปลักษณ์ได้ แต่ Z400 สามารถแนะนำผู้ที่เข้าแข่งขันในการแข่งขัน Gymkhana กับ Normal master
High SIDE อาจไม่ทำงาน แต่ SlipDown จะให้การป้องกัน
การถือครอง Anodized จะได้รับการยืนยันในอนาคต
การประมวลผลขอบมีความหย่อนคล้อยเล็กน้อยในบางพื้นที่ และโชคไม่ดีเล็กน้อยที่วัสดุชุบผิวลอกออกเล็กน้อยในบริเวณเหล่านี้
[รวมอะไหล่: พวกเขาเปิด?
สลักเกลียวสแตนเลส
[มีอะไรที่ทำให้คุณผิดหวังไหม?
การรักษาขอบ
จุดและแฮงค์ของการติดตั้ง
การคลายฝาถังน้ำมัน+สกรู
แรงผลัก 6 แรงหมุน 4
การติดตั้งน๊อตสแตนเลสที่ให้มา
เพื่อหลีกเลี่ยงอาการชักและปัญหาอื่นๆ ทุกครั้งที่ทำได้ ขอแนะนำให้ใช้ Anti-seeds, CopperThread, Molybdenum Grease และ Molybdenum anti-seizure agent เพื่อให้กระชับ
โปรดทราบว่าควรใช้ประแจหกเหลี่ยมในการติดตั้ง