หน้าแรก

【KITACO】Super Oil Pump Kit

    • ความพึงพอใจ:

      It is not installed yet

      • ผู้แสดงความคิดเห็น: Japan User(translated)
      • เผยแพร่เมื่อ: 2015-10-27 01:11:04
      Gasket is included as well, just replace it.
      I also thought about wearing at the same time as Bore up, but I thought I was going to wear it with another Timing.

      I tried turning by hand, but I go to Smooth.
      Precision looks good as well.

      I expect that it will be effective when installed.

      ตอบกลับ

      ลงทะเบียนเพื่อแสดงความคิดเห็น [ลงทะเบียนแบบสมบูรณ์]

      ความคิดเห็นอื่น ๆ

      [Webike Monitor] In connection with the

      88cc Bore up, that of Mr. KITACO was decided on in search of the strengthening Oil pump. for a light-oriented reason, as compared with
      other company's, Orifice expansion is also small -- carrying out -- quantity -- just for a moment -- it is less -- it is -- as -- although -- to a Normal head, I think that it is a cinch now.

      It exchanged from the NORMAL Pump simultaneously with formation of an 85-cc Bore up, and strengthening Clutch introduction. Since the futility of the three 2 times time-and-effort time and effort of work [ a direction ] or an Oil introduced simultaneously with them since it is necessary to remove the
      Clutch or to remove a Cylinder for Orifice processing was excluded, I thought that it was good. Since
      Orifice processing only expands a little existing hole, it attaches a Drill to a Pin vise and can expand it easily only by making it rotate by hand. Therefore, it is not necessary to remove a Stud bolt. It expanded to 1.4 mm this time. If generation of heat by a Bore up is considered as the
      Manufacturer also recommends, I will think whether it is safer to carry out strengthening of an Oil pump.

      Bore up, Clutch We replaced the Oil pump after the exchange.
      Replace itself by removing + Screw 3, replace Gasket, just align the cutouts of the shaft.

      Orifice 1. PinDrill is useful for extending to 5 mm.
      If you do not leave Stud bolt you will not get ordinary Drill.
      Case is Aluminum, so I was able to scrape crisply with a thumbwheel.

      Gasket is included as well, just replace it.
      I also thought about wearing at the same time as Bore up, but I thought I was going to wear it with another Timing.

      I tried turning by hand, but I go to Smooth.
      Precision looks good as well.

      I expect that it will be effective when installed.

      Bore up, Clutch We replaced the Oil pump after the exchange.
      Replace itself by removing + Screw 3, replace Gasket, just align the cutouts of the shaft.

      Orifice 1. PinDrill is useful for extending to 5 mm.
      If you do not leave Stud bolt you will not get ordinary Drill.
      Case is Aluminum, so I was able to scrape crisply with a thumbwheel.

      It exchanged from the NORMAL Pump simultaneously with formation of an 85-cc Bore up, and strengthening Clutch introduction. Since the futility of the three 2 times time-and-effort time and effort of work [ a direction ] or an Oil introduced simultaneously with them since it is necessary to remove the
      Clutch or to remove a Cylinder for Orifice processing was excluded, I thought that it was good. Since
      Orifice processing only expands a little existing hole, it attaches a Drill to a Pin vise and can expand it easily only by making it rotate by hand. Therefore, it is not necessary to remove a Stud bolt. It expanded to 1.4 mm this time. If generation of heat by a Bore up is considered as the
      Manufacturer also recommends, I will think whether it is safer to carry out strengthening of an Oil pump.

      [Webike Monitor] In connection with the

      88cc Bore up, that of Mr. KITACO was decided on in search of the strengthening Oil pump. for a light-oriented reason, as compared with
      other company's, Orifice expansion is also small -- carrying out -- quantity -- just for a moment -- it is less -- it is -- as -- although -- to a Normal head, I think that it is a cinch now.