Please login to check coupons
Quantity
100% Original
7 Days Warranty
Free Cashback
Net Price
Applicable Models
See all
Φ22.2, grip outer diameter: Φ33, for 12V cars only
Product Detail
Specification
[Compatibility]・Handle Diameter: Φ22.2
・Grip outer diameter: Φ33
・Compatible grip length: 115 / 120 / 130mm
・Exclusive for 12V vehicles
[Components] Heat-shrinkable tube for grip protection
Description
[Product Features]
・The integrated switch allows for smart operation.The 5-step temperature control is indicated by a 5-color LED lamp.
・The grip length can be adjusted to 115 / 120 / 130mm with 3 sizes of extended sleeves.
・The removable bar end cap is compatible with both bar end type and non-through type.
・Grip design for reliable maneuverability and thermal conductivity.
・The smallest diameter Φ33 provides a comfortable grip even if it is replaced with a regular grip.
・The nichrome wire is wound around the entire circumference of the hand to warm the entire palm.
・5 levels of temperature control and power consumption.*The temperature was measured at 25 degrees Celsius, no wind, and voltage 13.5V.The temperature may be lower than the measured value due to heat radiation to the handlebar, bar end, gloves, and cooling by stream.
・With a voltage suppression function, it is safe even at low voltage.
・When the voltage becomes less than 11.5V, the heating is automatically stopped, and when the voltage recovers, the heating is automatically restarted.
・Heat shrink grip protection tube" included!During the season when the grip heater is not used, this item is useful to prevent wear of the expensive grip heater.Simply cut to fit the grip length, attach to the grip, and heat shrink with a heat gun.
・The integrated switch allows for smart operation.The 5-step temperature control is indicated by a 5-color LED lamp.
・The grip length can be adjusted to 115 / 120 / 130mm with 3 sizes of extended sleeves.
・The removable bar end cap is compatible with both bar end type and non-through type.
・Grip design for reliable maneuverability and thermal conductivity.
・The smallest diameter Φ33 provides a comfortable grip even if it is replaced with a regular grip.
・The nichrome wire is wound around the entire circumference of the hand to warm the entire palm.
・5 levels of temperature control and power consumption.*The temperature was measured at 25 degrees Celsius, no wind, and voltage 13.5V.The temperature may be lower than the measured value due to heat radiation to the handlebar, bar end, gloves, and cooling by stream.
・With a voltage suppression function, it is safe even at low voltage.
・When the voltage becomes less than 11.5V, the heating is automatically stopped, and when the voltage recovers, the heating is automatically restarted.
・Heat shrink grip protection tube" included!During the season when the grip heater is not used, this item is useful to prevent wear of the expensive grip heater.Simply cut to fit the grip length, attach to the grip, and heat shrink with a heat gun.
Caution
*Not for use with vehicles with small handlebars (Φless than 22.2), inch bars (Φ25.4), or vehicles with low battery capacity or power generation.(A voltage of 12.5V is required for start-up)*When installing the supplied extension sleeve, apply adhesive to the inside of the extension sleeve where it meets the grip, and crimp it firmly.Please note that extreme load on the extending sleeve may lead to the falling off of the extending sleeve or the breakage of the grip end and the extending sleeve.
*Please understand in advance that you may feel lower temperature due to the heat radiation to the handlebars, bar ends and gloves, and cooling by the driving wind.
*Use a heat gun to install the heat shrink tubing for grip protection provided.Also, when the grip heater is heated, the protective tube may soften and loosen due to the heat, so it is recommended to install it when the heater is not in use.
*If the tube becomes loose after installation, heat shrink it again with a heat gun to make it tighter to the grip.If it still does not adhere, please remove the product as it may be the end of its life.
*The total length of the protective tube has a tolerance of plus or minus 3mm due to its characteristics.The edge of the product may be slightly slanted, but this is not a defect.
*The inner diameter of the right grip is Φ25.4.If the throttle sleeve of the vehicle to be installed has ribs, cut them to a height not lower than the inner diameter of the grip before installation.If the outer diameter of the throttle sleeve is smaller than the inner diameter of the grip and the throttle sleeve is loose, use the supplied aluminum seal to adjust the gap between the throttle sleeve and the grip.
*This product may not be used for SUZUKI vehicles with low battery capacity and power generation, or HONDA vehicles with batteries less than 7S.
*Yamaha vehicles with 4B5 or higher batteries can be used.
Applicable Models
Φ22.2, grip outer diameter: Φ33, for 12V cars only
