PAGE TOP

【P&A International】Extender Fender

Product images are for illustrative purposes only and may differ from the actual product.
Price: ฿3,250
Webike Points: 33

Applicable Models:

MT-09 17-21

MT-09 13-16

MT-09 SP 18-

See More

Best Selling Products

Product detail

[Caution]

*The photo of the product is only for an image. Please use it as a reference. There are cases that the actual product might be different from the product on the photo such as installation model, color and etc.
*The actual product might be different in color, shape compared to the product on the photo due to product improvement and specification changes.
*In addition, the other product might be reflected to the photo for the convenience of the photo shooting but this product will be deliver based on the title of the item.
*Please note that all instruction manual are written in English and other foreign languages.

[Description]

It protects the vehicle body and driver from splash of water or mud by extending the length of OEM front fender.
Since it is designed by model, it matches with the vehicle design without feeling a sense of incongruity.
You can easily install it by using the attached with a strong adhesive sheet.
It will not come off during normal use. However, we recommend the attached screws to secure it firmly in place..
It exerts its effect without disturbing the original design of the vehicle.
It is very effective in preventing splashes and mud splashes when driving in the rain or on rough roads..

Applicable Models

    • MT-09 17-21
    • MT-09 13-16
    • MT-09 SP 18-
    • MT-09 Tracer 15-17
    • Tracer 900GT 18-

Reviews

  • 3.8

    39 Reviews

  • 5

    Perfect

    3

    4

    Very Good

    25

    3

    OK

    11

    2

    Poor

    0

    1

    Very Poor

    0
  • Write a review

    It installed in VFR 800F.
    Remove Front Fender from the vehicle and remove the supplied Double-sided Tape and install the product.
    After that, 4 holes are opened at 4 places and the attached Pin is inserted and completed.
    (Fixing with Double-sided Tape alone is uneasy)
    However, because the width is slightly smaller than Front Fender, I feel that I pulled it with fixed Pin..
    Although it does not understand to the appearance, ....
    I think that it seems high if I think of them, but the person who was there is more muddy the condition changes.

    (What made you decide the purchase?)
    I joined a certain Events the other day and got pouring rain on the way home, raining from the top of the Engine to the inside of Cowl, struggling to clean up and clean up. Also, as muddy sticks, I will spoil the preciously polished Exhaust pipe, so I bought it with reference to the other reviewers.
    (How was it actually used?)
    I still can not say because I am not running, but 15 centimeters has been longer than OEMFender, so my expectation is Large.
    【Was it difficult to install? (Hard parts case)】
    Ultra Strong Double-Sided Tape for installing the exterior parts of the car was abundant because there were only a few Double-sided Tape which was originally attached, so I tried installing it in detail.
    【Please tell me the point of installation and hang (in the case of Hard parts)】
    The Ultra Strong Double-Sided Tape I wrote earlier was too strong, trying to position it, even if I tried to peel off, I could not peel off well and it was slightly misaligned. Let's say good because you do not have to worry about peeling while running.
    In Instruction Manual, it is better to remove Fender and not to say that it is not written. Screw attached to Front fork, Quantity : Pair (for Left and Right) It is easy because it only removes a total of 4. It is necessary to pay attention not to add Wound only when pulling out and putting it.
    [Is there anything I was disappointed about?]
    I wanted you to attach a double-sided tape a little more. It happened because it happened to have a Double-sided Tape, but it was a place I had to go to buy.
    【Hope for Manufacturer ? Please let me know if there are any improvement points]
    Increasing Double-sided Tape, it's still a price. Because there was a point, there are a lot of people who have flown into purchasing, so I expect in the future.
    【Have you compared items?】
    I can not find it in particular..

    "Front Fender" of "Additional Fender extending the rear end" So, you can reduce the damage from stone etc by winding up to Radiator Parts. That's it. That's it, "mono" As simple as "Plastic" As a Material of "ABS resin" Is it a neighborhood? It is finished in satin finish, just made it in the shape of Fender "Board". It's only 5400 yen for Kore ....
    Installation is basically preliminarily attached "Double-sided Tape". Just this Double-sided Tape, 8 mm wide and 10 cm in length, but only in 3 places, whatever you think "not enough" I feel it.. Tentatively "3rd car exterior wearing Strong Double-sided Tape" Add. Perhaps in anticipation of it, "Pin" Also comes with 4. However, "Pin" To install with "Fender" When "Extender Fender" It is necessary to install a hole in a hole in the Fender, so we will remove the Fender from the car body.
    Moreover, "Extender Fender" As such accuracy is not so high, Extender's "Miso" When "Fender" Because it does not fit together, fit together at the Large body, paste. From there "Snap pin" Attach the hole of Snap pin to 4. 5 mm at Hand drilletc. You can easily open the hole with, but as it is too much towards the end, the strength will be low, so we will drill a hole around 4 ends around 10 mm from the end. However, at this moment the miso with Fender does not match well, so "Extender Fender" It is possible to clear and to fix it "Pin" Because there is a case where the length is not enough and the kitchen will not end, "Sedimentary head" In principle, 5. I need to dig a little with 5 mm Drill. After that Plastic hammeretc. If you push in Pin and fix it with chitin, chitin, "Front Fender" Attached to the car body again. As time will be completed in 30 minutes.
    It does not mean that honesty is visible and the driving performance improves, just "Front tire" Water splashed up from the Guard than usual.
    Is it necessary? "No need" is not it.

    As the mud to the Radiator is bad at the time of running on a wet road, if you extend the Front fender you think that it will be a little better..
    "Texture"
    It's just black material, not so good. It is also a place that I can not see much from the outside, and since Front fender itself is black color, I do not care much about it.
    "Mounting"
    1. Front fender desorption (Because it is easy to work)
    Brake hose clamp about Fender part is disturbing, hard to detach.
    2. Since the installation accuracy interferes a little with the Rivet part of Brake hose clamp inside the Fender, I cut away the extender to be attached with Cutter about 2 mm. Then Just fit.
    3. Standard Double-sided Tape is too cheap for installation, so we added a commercially available Strong Double-sided Tape. Mounting with Fender Degrease the Extender with PearlCleaner, warm it with Dryer and paste it.
    4. It seemed that there was no problem with Double-sided Tape alone, but fixed in the attached Pin. (Drill with 2 mm Drill)
    Although the product is an impression that it is a little expensive from Material and texture, I am generally satisfied.

    Right and Left 's Curve is indeed
    Not the same, One Side was a short product. Probably not enough to change the Gold type budget
    Microfabricated workshop (It is not a factory or a company) Is it made of.
    It seems not a problem of finishing after molding.
    So it is impossible to ask for quality improvement.
    If you make the same thing individually, if you have time, materials and techniques you can make it in \ 500
    Let's stop it.. \ 5000 I bought it because it is safe and I can complain.
    There is nothing problem with the installation state. Be familiar with the fans beautifully.
    It is a feeling that the mud bounced by Engine by about 60%.
    I installed it securely in three locations with Double-sided Tape and Screw stopper.

    I felt uneasy with the attached Double-sided Tape so I added about 2 columns and installed it.
    I think that the jump of the puddle has been alleviated.
    Color : Because it is Unpainted and a simple shape it may be nice if it is a bit cheaper.

39 reviews View all

Most Viewed Products

【SP Takegawa】Down Fender Bracket
Down Fender Bracket SP Takegawa APE50
【UFO】Front Fender
Front Fender UFO CRM250R
【POLISPORT】Front Fender
Front Fender POLISPORT KX250F
【YAMAHA】Front Fender Trim Rail
Front Fender Trim Rail YAMAHA DRAGSTAR 400 Classic (XVS400, V-Star400)
【SP Takegawa】Front Fender
Front Fender SP Takegawa GORILLA
【P&A International】Extender Fender
Extender Fender P&A International Z250 (2013-)
【SAITANIYA】Front Fender
Front Fender SAITANIYA NSR50
【P&A International】Extend Fender
Extend Fender P&A International Z900RS
【STING R&D】Front Fender
Front Fender STING R&D ZZR1100 (ZX-11)
【KN Planning】Aluminum Front Fender Bolt
Aluminum Front Fender Bolt KN Planning CYGNUS X 125 (NCX125)
【P&A International】Extender Fender
Extender Fender P&A International V-STROM 650 (DL650)
【P&A International】Extender Fender
Extender Fender P&A International BANDIT650 (GSF650)
【SSK】Front Fender
Front Fender SSK Ninja1000 (Z1000SX)
【UFO】Front Fender
Front Fender UFO CRF250R
【TANAKA TRADING】Fender Mount Grommet
Fender Mount Grommet TANAKA TRADING GORILLA
【POLISPORT】Front Fender
Front Fender POLISPORT KX85
【Moto Salgo】Front Mudguard
Front Mudguard Moto Salgo CT125 Hunter Cub
【SSK】Front Fender
Front Fender SSK Monkey 125
【SP Takegawa】ABS Front Fender Garnish
ABS Front Fender Garnish SP Takegawa SUPER CUB 50 (C50)