Please login to check coupons
Quantity
100% Original
7 Days Warranty
Free Cashback
Net Price
Applicable Models
See all
CB900 F (SC09)
CB900 F (SC01)
CB750 F (RC04)
Show more
Product Detail
Specification
Material: SteelSurface finish: plating treatment
Instruction manual included
Description
This collar enables to install the swingarm for Suzuki GSX750S Katana 1100S Katana on CB750F/900F.
KATANA swingarm is designed to be used with the asymmetrical CB-F swingarm.
To solve this problem, the width of the left and right collar is changed to offset the Katana swingarm.
Both the wheel center and chain line are correctly positioned to allow bolt-on installation to the stock CB-F wheels and brakes.
The material is steel for strength.
The surface is plated to prevent rusting.
If you change to Katana swingarm, wheel, wheel collar, caliper support and torque rod of CB750F / CB900F can be used.
Pivot shaft is for CB-F and axle shaft is for both CB-F and Katana.
The cap of the swingarm pivot, the collar inside the pivot and the chain adjuster must be used for Katana.
Comes with an instruction manual.
[About the bushing width of the swingarm suspension support part]
The bushing of the suspension support should be replaced with the stock bushing for CB-F. Or, if you use the bushing for Katana, cut it down to 19mm width.(*See image 4)
*The stock bushing part number for CB-F is 40548-268-000 [for CB750FZ] and 52451-357-000 [for CB750FA-FC], both of them can be used.
(The width of the outer circumference of the bush is for CB750FZ (18mm) and for CB750FA-FC (16mm), but the width (19mm), inner diameter (10mm) and outer diameter (22mm) of the center of the bush are the same for both bushes)
KATANA swingarm is designed to be used with the asymmetrical CB-F swingarm.
To solve this problem, the width of the left and right collar is changed to offset the Katana swingarm.
Both the wheel center and chain line are correctly positioned to allow bolt-on installation to the stock CB-F wheels and brakes.
The material is steel for strength.
The surface is plated to prevent rusting.
If you change to Katana swingarm, wheel, wheel collar, caliper support and torque rod of CB750F / CB900F can be used.
Pivot shaft is for CB-F and axle shaft is for both CB-F and Katana.
The cap of the swingarm pivot, the collar inside the pivot and the chain adjuster must be used for Katana.
Comes with an instruction manual.
[About the bushing width of the swingarm suspension support part]
The bushing of the suspension support should be replaced with the stock bushing for CB-F. Or, if you use the bushing for Katana, cut it down to 19mm width.(*See image 4)
*The stock bushing part number for CB-F is 40548-268-000 [for CB750FZ] and 52451-357-000 [for CB750FA-FC], both of them can be used.
(The width of the outer circumference of the bush is for CB750FZ (18mm) and for CB750FA-FC (16mm), but the width (19mm), inner diameter (10mm) and outer diameter (22mm) of the center of the bush are the same for both bushes)
Note
* The image is only for reference. The image shown may differ from the actual product.
Caution
*Not suitable for CB750FZ with 14mm pivot shaft diameter.*CB1100F wheels and caliper supports cannot be installed on KATANA swingarm.(Because the dimensions are different from CB750F / 900F)
*Bushing width of the swingarm is 19mm for CB-F and 22mm for KATANA, so if you want to use CB-F rear suspension, you need to replace the bushing with CB-F stock bushing or cut down the bushing for KATANA to 19mm width.
*Since the swingarm length of the Katana is longer than that of the CB-F, it is necessary to change the chain.
The number of links depends on the T of the front and rear sprockets, so be sure to determine the number of links by matching the actual sprockets.(In case of Japanese specification CB750FA / FB / FC with stock sprocket T number, 108 links are required if you change to KATANA swingarm as opposed to stock chain link number 106)
Applicable Models
CB900 F (SC09)
CB900 F (SC01)
CB750 F (RC04)
Show more
