Reviews
I am generally satisfied, but I would like to have a larger size.
I like the affordable price and the Grip feel and have purchased several times now.
The size is one size, so depending on the vehicle, one piece may not be enough.
View detail
For preventing scratches on top case, etc.
[How is it used?
Tank Pad, but I use it to prevent scratches on the Top case.
I have been using this product for some time now, sticking it to Pannier and other products for scratch prevention purposes, and I can keep it on for years.
I like it very much and it does not peel off.
Also, the Quantity of Large Thread:It is 1pc. and may be used with Cut.
Was the one you received as per Image?
It is flexible and stretches slightly as shown in the Image. It is very easy to stick, does not wrinkle, and does not peel off.
How was your experience with it?
It is soft and easy to use, even if it is slightly scratched, it does not tear easily.
[Points to note]
Cutting with a cutter is a bit confusing because of the growth.
Once practiced, the Level is fine.
How did it compare to other products?
Cost-wise it is quite cheap, but I am sure of the quality and performance. I have been using it for a long time.
Other items that would be helpful
I think that the installation can be put on Beauty with just a certain amount of location, sticking it on, and fine-tuning while stretching it.
Immediately after the application - for a few days - it would be a good idea to press down on any floating areas.
View detail
Pretty good!
With or without it, the ease of folding will of course depend on how easy it is to ride the tank It's a good idea to put this on because it changes the form too, when you're running Circuit! I'm going to wear a leather suit, and it's going to get a little tattered, but for the price, it's good! View detail
I can run without worrying about it
Material in Knee grip:I bought it because the plastic frosted tank cover became slippery
It's a bit squishy with a certain thickness and elasticity
Because of its thickness, it doesn't have that tightly held feeling, but the hold is solid It's done and it's good enough
View detail
Pitt !!
I do not like that Garbage collects in the part where Seat hits Tank, Tank does not want to drink White like it, I purchased this item in various ways.
Adhesion is strong, so it stretches, so it sticks to me as thoughtful !!. After that, it is easier to cut and the rest seems to be usable (I want to fill the gap). Cut to about half in the image.
View detail
Tank Pad
When it is leather Pants, there is Gap etc. at hang off, Position does not fit, so we were thinking about Pad purchase, but we found this high product with high Cost performance and purchased.
Because it is not by car model, processing such as cutting is necessary, but it is easy to cut with scissors, so processing is very easy. Also, than the thickness I thought (3 mm Meter) There is firm adhesion, the surface is also processed like SnakeSkin, so feel comfortable and Gapetc. No, I can firmly hold it.
However, since Material is Sponge, I think that it will be scraped when the number of contacts increases, so I think that it is necessary to change it at that time, but the price is much cheaper compared to other products, so even if the frequency of replacement increases I think there is no problem.
Because it is a very highly cospa product, it is recommended for those who are considering purchasing Tank Pad.
View detail
Since it was the first Tank-pad purchase, although it wavered, it was made the product made from a reputable Magical racing whether it would be made pure.Is the handle of the sheet outer skin of FAZER8 (2013) also resembled?Since it was not the elegan
Since it was the first Tank-pad purchase, although it wavered, it was made the product made from a reputable Magical racing whether it would be made pure.Is the handle of the sheet outer skin of
FAZER8 (2013) also resembled?Since it was not the elegance only for
, it was not able to attach, without suiting Tank form, but it was processed drastically.The procedure is easy.Pasteboard is cut into the form of the
Tank pad.The
paper pattern is set by a Tank, and an excessive portion is turned up.
(3) An excessive portion is cut.Become symmetrical at this time.
(4) It is checked again whether according to a Tank, it is satisfactory.The paper pattern like the point is set and it cuts into the pasteboard of the double-stick tape of the
Tank pad by a Cutter.Or [ that it is better to cut more shallowly by not cutting at once several times at this time ].A break is shallowly put in in the center of the pasteboard of
double-stick tape.He plans to turn off only the pasteboard to the last.Position doubling is carried out to the
Tank, and one side of pasteboard which put in the break like the point is stuck so that it may not shift removing little by little.In that case, it is good to work carefully so that a joint may not overlap or a crevice may not open.Although front riding was not carried out usually [ ], it is the favor which stuck the Tank pad and the weight shift became possible drastically.
View detail
It is touch like an about 3-mm Sponge, and is hard to slide on the surface. Although stuck, since a Wound does not enter even if it leans on a Tank, I think that it is good. Since the portion which carries out a Knee grip is not started at all
It is touch like an about 3-mm Sponge, and is hard to slide on the surface.
Although stuck, since a Wound does not enter even if it leans on a Tank, I think that it is good.
Since the portion which carries out a Knee grip is not started at all, it is kana [ want / the object for them ].
Since two sheets and one size were attached,
Sticker smallness was good.
Although it does not understand where
size is used ...
View detail