Reviews
Quite tense when pasting.
[How is it used?
Since the Tank and Seat are in close contact, the longer the ride, the more fine abrasions will appear on the Tank.
I bought this product to prevent that. 2 sizes, LargeSmall, 3 sheets in total, can be shaped with scissors.
How was your experience with it?
It is quite thin in thickness but seems to be resistant to abrasions. After making a paper pattern to make a similar shape to the contact surface, it can be cut along the pattern to make a shape that corresponds to the contact surface. However, while it is easy to cut, this Seat does not seem to be able to protect against sharp objects. Durability is hard to say at this point.
How did it compare to other products?
This is my first time using this type of product.
[Points to note]
I bought the one with luster and carefully applied it to a glossy tank, but it has a few air bubbles, and as noted in the notes, there are wrinkles where there are curved surfaces. It seems that you don't need to worry about it if the shape is simple.
View detail
Is good
I put it on to prevent scratches and scuffs caused by the attachment of Net and luggage, and also to prevent scratches on the fuel tank and Seat interference area.
[Color] It is clear, so it is not noticeable and will not detract from your motorcycle's design. It provides good protection.
View detail
I use it every year.
I use a magnet type tank bag for long touring, but the tank bag moves a little when it touches my body during getting in/out of the car and driving.
Is it good for the painted surface to leave it on? I think it is not good for the painted surface, so I use it every year around October at the end of long touring. The period of use is about 7 months for a large car.
I put it up in the garage at 15℃ or higher with the heater on, so that the seat is soft and the tank is not cold.
The large size is 90×60, so it is not so difficult to apply.
? The peel can be removed without much difficulty by lifting the corner.
After use, the tank is in good condition, with no wound on the tank and no adverse effects such as discoloration on the paint.
The product comes in one 180×120 and two 12 The product contains one 180×120 and two 12×90, which is very useful because we use four 90×6×90 in the Tank Bag. The product is very useful because it can be used for exactly two seasons since four 90×6×0 sheets are used in the Tank Bag.
Easy to use and good product for preventing scrubbing Wound.
View detail
I'm keeping the face of the exclusive.
It is used for the car body Left Side which tends to be damaged by jeans in the place where Seat bag and Tail cowl rub and push walking.
It is a relatively thick Seat with high transparency.
It's soft, so it tracks reasonably well and stretches a bit if you pull on it.
The adhesive strength is relatively strong, so it won't come off by itself, and if you want to remove it, you can do so without leaving any adhesive residue.
It will protect against frictional scratches such as scuffs on the seat back and tail cowl.
On the other hand, Scratch system scratches such as scratching with hard objects may not be able to protect the product because this product will tear.
I recommend 3M's Die KnockSeat for those areas.
(For better or worse over there, Material:Carbon Style, though)
By the way, it is convenient to have Masking tape to mold and apply this product to Beauty.
? Put masking tape on the part of the car body that you want to protect.
Write the type on the masking tape
? masking tape to the surface of this product.
? Cut to size
The moulding is completed with
This product can be reapplied a little at a time, so you can take a shot at it.
If you are unsure, use water paste.
Since Seat is colorless and transparent, be careful of fingerprint adhesion and air bites on the adhesive surface.
In general, Seat is easy to use as a Protector.
It is not so expensive, so you can try to put it on the part you are worried about once.
View detail
Very good product
Always stocked with scratch protection.Recommendation. View detail
It is highly protective.
It is effective in preventing scratches and scratches on the interfering parts of the Fuel Tank and Seat due to the installation of the Rear Cowl Net. [Color] It's clear so it doesn't stand out and doesn't detract from the design of the motorcycle. View detail
Thin, durable and unobtrusive
When I anchored the Seat, my inner thighs started to hit the side cover
Because it is a limited color of the last model, I did not want to put Wound on it I bought this product in a pack of three, between LeftRight+Tank and Seat
I installed it with the heat gun while stretching it a little bit, so I'm very happy with it without any wrinkles I was able to install it in the finished product
Who would think of a niche product like this? It was convenient and satisfying
View detail
To wrinkle
I was wrinkled again ~.
I purchased it a few times, I pasted it, but it will not go well.
That's too bad..
It is attached with a loose curved surface so as to pull somewhat,
I will become a little wrinkle by all means.
I hope Dryer can be used, but it can not be helped because it is incompatible.
I bought it cheaply at the time of Sale, so I regard it as good.
View detail
In my case it is an essential item.
Footpeg Inside Shoes hit the part we used before. There is a part which peels off a little because of the rubbing of Shoes, there is a dirt entering there, Black sometimes gets clogged, we are replacing once a year. Although there is no problem in terms of performance, I think that the price is a bit high. View detail
To prevent scratches
Purchase this item for scratch prevention
Since there is Luster, it will not cloud only when stretched
Be careful as fingerprints are attached to the adhesive surface
View detail
To prevent scratching of Cowl
In case of one piece, purchase here for the use of multiple places, In my car, there is no Loading Hook in Rear so Tension can be applied from around T foot footpeg : I've fixed my baggage at Belt of Rubber, but I will use this because it will inevitably interfere with Rear Fender.
Because it is Clear, it is inconspicuous Quantity : 1 Set of 2pcs. You can use Cut freely as Large Ki is enough.
View detail
Instead of Tank Pad
SR 400 FI interferes with OEM Tank and Seat and rubs it, so purchase for scratch prevention.
This type has a transparent feeling and the color of the base is clearly visible, and furthermore it is thick and it seems that durability can be expected.
View detail
Protector sheet
Handlebar section, purchased to protect scratches around Main key.
Seat has a thickness, I think that it can cope with even a little rubbing. Moreover, Seat's follow-up property is good with respect to the shape to be attached, and it is very easy to process.
Because it is transparent, it is also an advantage that it is inconspicuous even if stuck, so it was very satisfying to purchase.
View detail
This time 4th time
【What made you decide the purchase?】 From the price and past experience.
【How was it actually used?】 After all the bent place is absolutely hard - Bubbles enter.
【Was it difficult to install? (Hard parts case)】 Any item
【Please tell me the point of installation and hang (in the case of Hard parts)】 Any item
[Is there anything I was disappointed about?] Glossiness etc.. There is no problem. I do not know well which one can cut cleanly when cutting with Scissors and Cutter.
【Hope for Manufacturer - Please let me know if there are any improvement points; I hope there is a little more thickness. It is still better if the surface is easy to paste.
【Have you compared items?】 DAYTONA : High protection seal.
[Others]
View detail
Structure is solid more than the price. Those who run the Circuit need to try.
Structure is solid more than the price.
Those who run the
Circuit need to try.
View detail
Since peeling of crack prevention and a Sticker can also be prevented, it is considerably found useful.
Since peeling of crack prevention and a Sticker can also be prevented, it is considerably found useful. View detail
Since this product is a Seal with gloss, it is fit for protecting a glossy Cowl from an abrasion. If it sticks on an extreme curved surface, air bubbles will enter, but the attachment itself is easy. Since one large sheet and two small sheets are contai
Since this product is a Seal with gloss, it is fit for protecting a glossy Cowl from an abrasion. If it sticks on an extreme curved surface, air bubbles will enter, but the attachment itself is easy. Since one large sheet and two small sheets are contained, if the one as it is where the smaller one is larger is used according to the form of a part to stick, cutting, it will think that it is good. View detail
Since the belt for attachment of a seat bag buffered in a seat cowl, the sheet here was used. When it stuck lengthening this sheet so that air could not be entered, and lengthening, the fingerprint remained in the adhesion side and was not able to sti
Since the belt for attachment of a seat bag buffered in a seat cowl, the sheet here was used.
When it stuck lengthening this sheet so that air could not be entered, and lengthening, the fingerprint remained in the adhesion side and was not able to stick finely.
Then, when resticking in the same way as an ordinary seal, it was able to stick finely, without being conspicuous.
Most paste after removing a sheet did not remain.
View detail