Reviews
Headlight ON/OFF functionality good.
I want to keep LightOff as much as possible during the daytime to protect the Light case Wiring from heat. View detail
Fits: Others , SUZUKI GSX400, YAMAHA XJR400, HONDA CB400SF
It purchases in order to attach to XR250. After all, in order to reduce the burden of a battery, it attached. In perfect coupler on, anyone can do connection simply. If there is no space just for a moment although a switch is attached to handl
It purchases in order to attach to XR250.
After all, in order to reduce the burden of a battery, it attached.
In perfect coupler on, anyone can do connection simply.
If there is no space just for a moment although a switch is attached to handle left-hand side, it is tight.
It has been confused just for a moment.
It is from whether it becomes a measure against water proof by placing the exit of wiring upside down, and a thought to have attached the switch to the up-and-down contrary.
(since a place with quite a many water is run in case of off) Probably, it will be safer to wind by a vinyl tape, since the connection section of the headlight coupler is not waterproofed.
In addition, although it will dedicate to the flesh side of a headlight cowl, it is tight if there is no space also here.
It is likely to disconnect, while turning a wheel repeatedly, if it stores forcibly.
If the hit also takes care and is attached, I will think that it is satisfactory.
Although an honest effect cannot be felt clearly, I think that it is good for a battery absolutely.
I think that they are goods as which easy wearing may be sufficient.
View detail
Fits: Others , SUZUKI GSX400, YAMAHA XJR400, HONDA CB400SF
since a switch will become very hard if a set screw is fastened too much -- business -- they are cautions. The rest is satisfied.
since a switch will become very hard if a set screw is fastened too much -- business -- they are cautions.
The rest is satisfied.
View detail
Fits: Others , SUZUKI GSX400, YAMAHA XJR400, HONDA CB400SF
The design of attachment is also good at an easy.
The design of attachment is also good at an easy. View detail
Switch
This is installed along with the relocation of switches.
Light can be turned on and off. The BlinkerPush can now be used to reset, and the operability is good.
It may depend on the handlebar, but there seemed to be interference with the tank when the handlebar was turned down to its full length, and some fine adjustment was necessary.
It would be nice if it were a little less protruding and a little more compact.
View detail
Best
The second time I ordered, my friend saw that the headlight could be turned off and asked me how I did it. I said that I replaced this kitao headlight ON/OFF switch kit. The first one is beautiful in appearance and practical in function, because the honda ape 50 original There is no headlight that can be turned off in the factory. Although the price is a little expensive, the practicality is very high for me. View detail
D I diverted to Tracker.
The D Tracker doesn't have a Headlight On/Off Switch and Passing switch, so I diverted this switch kit to install it.
important item
[Was there anything that disappointed you?
There was nothing in particular
Do you have any wishes or improvements you would like to make for the Manufacturer?
Couldn't it be a little cheaper?
[Do you have any products to compare it to?
KN Planning's Universal Switch Kit Type 5 (Item #:SWITCH-06) I didn't buy this product because I couldn't switch the HI/LOW of the Headlight although the price is cheap.
Frequently Asked Items
What made you decide to buy?
Because there is not only Headlight On/Off Switch but also a switch for position light, which is made by reliable KITACO.
How was your experience with it?
It is convenient because the Headlight can be turned off while stopping the car. There is a switch for position light, so I added the position light.
Was the installation difficult?
The recombination of Wiring is a little troublesome, but it is not a problem if you do it steadily.
【Please tell me the installation point and hang】
You can add Tabs to individual wirings with masking tape and write HI and LOW to organize them and not get confused.
[Was the Instruction Manual easy to understand?
As expected of KITACO, the instruction manual is attached.
[Included Parts:were they on?
ShortWiring with Connector for Socket and Wiring Branch for bulbs is Quantity:2pc. Set. it was not used in the diversion to the D Tracker.
View detail
Fits: Others , SUZUKI GSX400, YAMAHA XJR400, HONDA CB400SF
Bring it on to save Battery!
Headlight, because FI Vehicles without a KICK is the life of Battery I put this product on because the switch is a necessity I have been using it to take over 3 motorcycles that I am currently installing, so this is a great deal for this price I can't say enough about the durability Installation depends on the motorcycle, but the NAKED system without the cowl I think it's relatively easy to do with Motorcycle But if you are used to Motorcycles covered by Cowl or Cover like Scooter, you should be used to it Otherwise, it may be hard for you Of course, you have to turn the Headlight on while driving so you can turn it on and off It is very useful to have the Switch I think any basic motorcycle can be used with a Valve car View detail
Fits: Others , SUZUKI GSX400, YAMAHA XJR400, HONDA CB400SF
Usefull and Simple
my motorbike is AHO (automatic head light on) so in traffic lights my battery drain so much times so i use this KITACO Headlight ON/OFF Switch Kit its very simple to install just remove headlight and plugt through the old head light harness and get switch to ur easy spot on handle bar and fit it. also quility of this product very high wires are strong and fat perfectly match to H4 builb , i suggest it to eduro rider or cassualy daily rider View detail
High Switch is good, is not it?
GORILLA 2V All LEDs are dropping voltage. 6VSpec. But installed without problems. Blinker, Hazard, LightOff, Passing No problem. It is to shed Earth firmly. LED Light is SYGN HOUSE 12W. View detail
Nice switch
It's very nice and solid switch but hard to install because there is not instruction in English. Finally done. 4* instead of 5* View detail
Fits: HONDA GORILLA, HONDA GORILLA, HONDA MONKEY
I diverted it to CRM 50 - - - It was a bit difficult. - - -
Switch was also annihilated at the time of restore of immovable CRM 50, so initially it is cheap about 2,000 yen for a certain dense forest site (Wiring diagram is obviously not obvious) I was wearing it while searching with Tester. However, it is not Push cancellation in that price range naturally It is very Push cancellation not using it is very stressful - - -
Since accuracy was also not good, I dared to introduce this product of domestic Push cancellation.
GORILLA and MONKEY can be attached according to the Instruction Manual street, but if it is diverted it will not work well unless Wiring is grasping somewhere.
After all it was finally attached by trial and error while comparing Wiring diagram of MONKEY and Wiring diagram of CRM 50 (^∇^;)
The operation feeling is different from the one of 2000 yen which is after all, even if it operates as Snap it is pleasant.
The price is also nice, and the performance of Body itself is good, is not it?
Just as it is diverted, Wiring diagram is still wanted, so I want to see the neighborhood like Meter of ACEWELL "Wiring where color goes wherever" I think that you can use it for a wider User if you write it.
View detail
I like the appearance the most.
Various Manufacturers are issuing,
It is rounded and I like it the most..
It is a dish that can be recommended with good operability.
Wiring was surprisingly large, and it was Large strange that there was quite a lot going into Headlight case.
Headlight ON / Since OFF is also attached,
Engine If you do not want to be charged at startup use Off, it may be nice to turn on when Engine is engaged.
View detail
Fits: Others , SUZUKI GSX400, YAMAHA XJR400, HONDA CB400SF
Easy installation
Mounting on TDM 850. As Headlight disappears at startup and maintenance, we expect Battery to last a long time. Wiring from Switch is facing upward, but I think that it is still better if we can change how to put it out. View detail
Fits: Others , SUZUKI GSX400, YAMAHA XJR400, HONDA CB400SF
Easy to install and Wiring
Although I installed other company's Hid Kit and Light switch EVO, I always contacted Manufacturer because it will be left open, but I do not understand the cause, so I will check shipping fee if I send it with you. I was told that. Since it does not understand even if you check out the shipping cost and seeing it, I bought it because I think that it is definitely possible to turn on and off Light if I make Plus a little on my shipping cost price.
Light on and off can be switched, so it will work properly. Since there is no Waterproof characteristic, since it applied the contact Grease to the contact, will it last long?
View detail
Fits: Others , SUZUKI GSX400, YAMAHA XJR400, HONDA CB400SF
The Headlight ON/OFF Switch was attached and carried out to 250TR.It is for Battery derating at the time of engine start.attachment was very easy, the Coupler was made to relay, and the switch body was only attached with the Handle.The exterior and th
The Headlight ON/OFF Switch was attached and carried out to 250TR.It is for Battery derating at the time of engine start.
attachment was very easy, the Coupler was made to relay, and the switch body was only attached with the Handle.The exterior and the character of the
Switch are classic and match 250TR exactly.Since the
Tail lamp is not interlocked with, I think soon that he would like to LED-ize a Tail lamp.
View detail
which can carry out the HI/LOW change of the Headlight of the second-half MONKEY of 6V -- in order to make it like, this set Switch was purchased.Although the Push cancellation and the Passing switch are also attached and it was not dissatisfied
which can carry out the HI/LOW change of the Headlight of the second-half MONKEY of 6V -- in order to make it like, this set Switch was purchased.Although the
Push cancellation and the Passing switch are also attached and it was not dissatisfied in the
function surface, as the second-half MONKEY of 6V had
necessity, dissatisfaction remained a little. [ which processes the Sub harness of a phon when attaching ]The mounting width of a main part is about 50 mm by (I consider that it is better to check with Manufacturer etc. when purchasing) reference.
View detail
He wants a Push cancellation to APEs and it is exchange. It is easy in case of a push type too. It is worrisome to become that it is likely to hit with a Tank at the angle.
He wants a Push cancellation to APEs and it is exchange.
It is easy in case of a push type too.
It is worrisome to become that it is likely to hit with a Tank at the
angle.
View detail
A very nice switch. However I had to contact Kitaco to get instructions in English as this is not a straight forward clip and go installation.
A very nice switch. However I had to contact Kitaco to get instructions in English as this is not a straight forward clip and go installation. View detail
Since it clamped for the handle, it was easy-to-use and attachment was also easy. although the kit itself also thinks too large somewhat kana -- the part -- since it is easy-to-use, it is considered as means.
Since it clamped for the handle, it was easy-to-use and attachment was also easy.
although the kit itself also thinks too large somewhat kana -- the part -- since it is easy-to-use, it is considered as means.
View detail